R2hobbies.com 3Ch EP 2M Thermo Glider VGA User manual

3Ch RC EP 2M
VGA Glider
rcpl3901001
P1 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
R2hobbies.com
Presents
3ChEP
2MThermoGlider
VGA
InstructionManual
You should read this Manual carefully before you play.
It contains important information for using the model.

3Ch RC EP 2M
VGA Glider
rcpl3901001
P2 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
Introduction
Thank you forchoosing R2hobbies 3Ch EP 2M Thermo Glider VGA,if you arethe first time to use this typeof Products, please
read thisstatement carefully and strictly in accordancewith therequirements ofoperation.
Youcouldrefer to themanual if youencounter any problemsduring theoperation. Pleasewell keep the manualafter use
becauseyoumighthaveto useit againnext time.
Onceagain, thanks forbuying our products.
About VGA Thermo Glider
As oneof R2hobbiesWingTeammember, VGA coveredwith A++ Oracover ontop of Balsa WoodMainWing. 100%Hand
MadeFRPFuselagegives Light but StrongFuselage.If you’relooking for abeginning budget RCGlider, you’vegot intothe
rightplace!
Specification
Length 995mm
Wingspan 2000mm
Motor 1000rpm/vD2836Brushless Motor
Radio Gear 3Chor above
Servo 3
Net Weight 1650g
Part List
# Item Qty Remarks
1. Fuselage 1 /
2. MiddleMainWing 1Pair /
3. SideMainWing 1Pair /
4. TailWingRudder 1 /
5. TailWingElevator 1Pair /
6. CabinCover 1 /
7. MainWingPoleL204mm 2 /
8. PushRodL585mm 1 /
9. PushRodL640mm 1 /
10. D43mmSpinner 1 /

3Ch RC EP 2M
VGA Glider
rcpl3901001
P3 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
Instruction
▶
Tail Wing
Installing Rudder
1)Insert Hinge into Pre-cut Kerf
2)Insert toMainTail Wing Pre-cut Kerf
Done

3Ch RC EP 2M
VGA Glider
rcpl3901001
P4 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
Install to Fuselage
Get readyforthe L585mm(Rudder) &L640mm(Elevator) Push Rod
*Tips Put theL640mm Push Rod First, thisstepis abit difficult which will taketimeto it.
1)Putthe L640mm Push Rod Inside 2)Lead thePush Rodout from the Side hole(Choose as yourhabits)
Done
3)Put the L585mm Push RodIntoFuselage 4) Pullit from theFuselage TailHole 5) Put on theClevises
6)Clip the Fiberglass Horn onTail Wing 7)Insert Control Horn into Pre-cut Hole & Clip it
Screwdrivercangivealittlehelpto
pushthe PushRodEndfrom the
Side Hole

3Ch RC EP 2M
VGA Glider
rcpl3901001
P5 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
Installing Elevator
Get readyfor theElevators
1)LoosenElevator MountingScrew 2)Insert CarbonFiber Rod
3)GroupingMainTailWing& Elevator 4)Fasten thescrews
Done
Remember
fullylossentheElevator
Mounting Screw or you can’t insert
theCarbonFiber Rod

3Ch RC EP 2M
VGA Glider
rcpl3901001
P6 -T6
Join our FREE Membership and accept 10%off Offer! R2hobbies.com
▶
Main Wing
Grouping
1)ApplytheEpoxy5 MinuteTypeAdhesiveGlueandstick theMiddleMainWing&SideMainWingwithMainWingPole
Mounting onto Fuselage
Screw L35mm Black PlasticScrew withBalsa Wood Screw Cover ontp Fuselage
Before Flight
Pleasecheckif all theoperation works wellBEFORE everyflight.
Makesure that all the devices are ingoodcondition. Run it before youfly.
Ready to FLY now!
We hope you’ll enjoy R2hobbies.com Product!
EnsurethePoleis insertedfirmly
intothe Main Wing or they can’
tbe
grouped