Radial Engineering JDX Direct-Drive User manual

Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam BC V3C 5M5
Tel: [phone] • Fax: [phone] • Email: [email protected]
User Guide
DIRECT-DRIVE

ATTENTION
The JDX Direct-Drive™ must be powered with an isolated power
supply (either a separate power supply or a multi-out power sup-
ply with each output being isolated.)
If an un-isolated power supply is used to power the Direct-Drive
in conjunction with another device that is also using the same un-
isolated power supply the Direct-Drive will shut down as a safety
feature to prevent damage to the unit. Switching to an isolated
supply will correct the problem.
Should the unit shut down, simply un-plug it from the un-isolated
power supply and plug it into an isolated one as described above
and the unit will power up.

JDX Direct-Drive™Amp Simulator and Direct Box
Overview.......................................................................................... 1
Features .......................................................................................... 2
Making Connections........................................................................ 3
Tone Voicing .................................................................................... 4
Rear Panel Connections...............................................................5-6
Block Diagram ................................................................................. 7
Specications .................................................................................. 8
Warranty ......................................................................... Back Cover
Thank you for choosing the Radial™ JDX Direct-Drive™. We believe this to be one of the most effective and convincing
tools for guitarists that play on the stage or in the studio, and want to do so without the use of a guitar amp.
The Direct-Drive was designed to be intuitive and easy to use. But as with all products, taking a few minutes to read the
manual will ensure a better understanding and increase your enjoyment.
If after you have done your homework, you nd yourself asking about something that may not be covered, please visit
the FAQ page on the web site. This is where we post questions from users and important updates. If after that you still do
not nd the answer you are looking for, feel free to send us a note at [email protected] and we will do our very best to
respond in short order.
Now get ready to blast away as if standing in front of a wall of amps… without any amp at all!

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
1
OVERVIEW
The JDX Direct-Drive™ is a unique device that emulates the sound of a guitar amplier while doubling up as a direct box.
In other words, with the Direct-Drive on a pedalboard, you can do a gig without carrying an amp to the club or record
silently using all your favorite pedals. The design begins with a ¼” guitar input and passive thru-put to feed a stage amp
plus a dedicated tuner output. The signal then passes through a series of lters to create Radial’s signature JDX™ tone.
This is modelled after the sound of a Shure SM57™ in front of a Marshall™ 4x12 cabinet. This is augmented with two
amp settings that add the character of a Marshall JCM™ head or Fender Twin™ combo to the mix. These can be further
tailored using a presence switch to add extra sparkle. The amp tone signal exits the Direct-Drive via either a ¼” guitar
level output or via a balanced XLR to feed the PA. The Direct-Drive may be powered using a dedicated standard 9V power
brick or an isolated power supply.
COMBO
‘Fender Twin’
STACK
‘Marshall JCM’
JDX 4x12
‘Cabinet with SM57’

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
2
FEATURES
1. INPUT: ¼” input for the guitar or bass.
2. OUT: ¼” ‘amp tone’ output used to feed a processor or second
amp.
3. XLR OUTPUT: Balanced mic level output used to feed the PA
system or recorder.
4. THRU: Used to feed the on-stage amplier.
5. TUNER: Hi-Z always-on output used to connect an electronic
tuner.
6. 9VDC: Standard Boss-style power supply connection.
7. POLARITY: Toggles pin-2 and pin-3 on the XLR out to phase-
align your amp with the stage monitors.
8. GROUND: Lifts pin-1 on the balanced XLR output to help
reduce hum and buzz caused by ground loops.
9. AMPLIFIER: Selects between COMBO, STACK and JDX for
distinctive amp tones.
10. PRESENCE: 2-position switch with bypass and on for extra
sparkle on the STACK & COMBO settings.
11. POWER: LED lets you know the Direct-Drive is ready and on.
1 2 3
4 5 6
79
810
11

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
3
MAKING CONNECTIONS
Before making connections, it is good practice to turn your PA or
recording system down as this will prevent connection and power-up
transients from damaging more sensitive components such as tweeters.
Plug a 9V power supply into the Direct-Drive. You can use any standard
Boss-style PSU directly into the Direct-Drive or an isolated power supply
to power; the power supply is not included. Once plugged in, the LED
will illuminate to let you know power is being received. A cable clamp is
available should you wish to lock in the power connection. Simply loosen
the screw, pass the power adaptor cable through the hole and re-tighten.
Set the four top-mounted switches to the off or bottom ‘start’ position.
To test, connect your guitar directly to the Direct-Drive input and the
XLR output to your PA or recording system. Begin playing as you slowly
increase the level on your audio system. Try the VOICING switch by
changing the amplier tones.
WARNING: If using a multi-pedal power supply, you must
ensure the DC outputs are isolated. If not properly isolated,
the power supply can damage the JDX Direct-Drive. Please
consult the power supply manufacturer to ensure the outputs
are isolated before connecting.

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
4
TONE VOICING
1. Bottom: JDX
This emulates the sound of a 4x12 cabinet with a mic. It tends to have a
fair bit of mid-range and works very well to cut through the mix.
2. Middle: STACK
This will bring out a ton of bottom end to produce a big fat tone. Try
adding a bit of top-end using the bright switch. This works like a
presence switch on an amp.
3. Top: COMBO
This creates a brighter more open tone. It sounds great on cleaner
signals using a delay and chorus. If you want more upper shimmer, try
using the bright switch.
You are now ready to add your guitar pedals. For fun, plug your guitar into
your overdrive, chorus and delay. Now go back and retest the amp settings
using distortion and effects. This is where the Direct-Drive truly comes to life!

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
85
REAR PANEL ¼” CONNECTIONS
There are four ¼” connectors on the rear panel along with the balanced XLR out:
1. INPUT
Used to connect your guitar or signal chain from effect pedals.
2. THRU
Bypasses all amp simulation and sends an untouched signal to your stage amp.
3. TUNER
Used to connect a tuner – keeping it out of the signal path.
4. OUT
Used to send the wet amp tone to recorder or second amplier.
1
2 3
4

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
6
REAR PANEL BALANCED OUTPUT
This active output is used to feed a PA or recording system. This follows
the AES standard with pin-1 ground, pin-2 (+) and pin-3 (-). It is a mic level
output and thus should be connected to a standard mic input on a mixer
or studio preamp. The XLR out has two top panel functions:
Polarity Reverse
This toggles pins-2 and 3 at the XLR output and is primarily used as a
creative tool to phase correct the direct output so that it better aligns with
a microphone in front of an amp. This of course assumes you are using
the ‘thru’ out to feed a stage amp and will be combining the two channels.
It can also be used if interfacing your Direct-Drive with an older vintage
preamp that may not follow the AES standard.
Ground lift
This disconnects pin-1 on the XLR to help reduce hum and buzz caused
by ground loops. Hum often nds its way into audio systems due to voltage
discrepancies within the power system. Lifting the ground disconnects
the audio ground in between the Direct-Drive and the PA or recording
system which can often alleviate noise. If you hear buzz, try pushing the
switch upwards.

Radial Engineering Ltd. JDX™ Direct-Drive™ User Guide
7
BLOCK DIAGRAM*
* Subject to change without notice.