Radiocrafts RC2400 User manual

Radiocrafts
EmbeddedWirelessSolutions RC2400/RC2400HP-ZNM-DK-USB
©2010 Radiocrafts AS RC24xxDK-USB Demonstration Kit Quick Start (rev. 1.3) Page 1 of 4
RC2400/RC2400HP-ZNM-DK-USB Demonstration Kit
Quick Start
Intro
The Demonstration Kit from Radiocrafts is designed to make it easy for the user to evaluate
the module, develop an application and build prototypes very quickly.
There are two paths the final module solution:
1. Use the demo boards/module with preloaded ZNM functionality
2. Write, compile and download your own FW to the module
Included in the kit
-3 Demo Boards including ZNM FW
-3 Antennas
-3 USB cables
-1 CC-debugger (programmer/debugger)
How to get started
Please follow this guideline to ensure that the USB driver is properly installed on your
computer before you connect the demo board to the PC.
1. Download the latest version of
RCTools-ZNM from
www.radiocrafts.com
2. Install the RCTools-ZNM as
described in the RCTools Installation
Guide. The USB Driver is
automatically installed together with
RCTools-ZM.
3. Connect the demo boards to the
PC after installing the RCTools PC
software. Connect the antenna or
connect to your test equipment.
4. You are now ready to use the Demo
Board. Radiocrafts offer a powerful
RCTools PC suite, but any terminal
program using COM ports can also
be used. Visit www.radiocrafts.com
to download relevant documents.

Radiocrafts
EmbeddedWirelessSolutions RC2400/RC2400HP-ZNM-DK-USB
©2010 Radiocrafts AS RC24xxDK-USB Demonstration Kit Quick Start (rev. 1.3) Page 2 of 4
Getting started with ZNM
Included in the RCTools (ZNM-CCT) there are two command files for easy setup and
communication between two boards. See ZNM-CCT User Manual for details on using ZNM-
CCT. This document also includes a step-by-step guide for setting up a simple network.

Radiocrafts
EmbeddedWirelessSolutions RC2400/RC2400HP-ZNM-DK-USB
©2010 Radiocrafts AS RC24xxDK-USB Demonstration Kit Quick Start (rev. 1.3) Page 3 of 4
Getting started creating your own FW
1. Download and install latest Z-stack for CC2530 from www.ti.com\z-stack
2. Download and install 30 days evaluation version of IAR EW8051 from
http://www.iar.com/website1/1.0.1.0/244/1/
3. Start IAR and open appropriate project included in Z-stack download
4. Compile for RC24xx and download/debug with CC-debugger
Figure 4 http:\\www.ti.com\z-stack
Figure 2 Your
ZigBee application
Figure 1 RC24xxDK-USB
Figure 3 www.iar.com

Radiocrafts
EmbeddedWirelessSolutions RC2400/RC2400HP-ZNM-DK-USB
©2010 Radiocrafts AS RC24xxDK-USB Demonstration Kit Quick Start (rev. 1.3) Page 4 of 4
Figure 5 Connecting CC-debugger to RC24xxDB
Related Documents on www.radiocrafts.com
-Module Data Sheet / User Manual (Module RF and embedded firmware description)
-RCxxxxDK-USB User Manual (Description of your Demo Board hardware)
-RCTools installation guide (Install/uninstall description)
-RCTools User Manuals (Description of the RCTools PC applications for your module)
Please visit the product page for the selected module to download all relevant documents.
More information
-Z-stack documentation included in Z-stack download
-IAR EW8051 documentation (www.iar.com)
Contact Information
Radiocrafts AS
Sandakerveien 64
NO-0484 OSLO
NORWAY
www.radiocrafts.com
[email protected]
[email protected]
[email protected]
Tel: [phone]
Fax: [phone]