Radiosistemi rr8 User manual

Warnings
Tools
Assembly Guides
SAFETY:
- This Model is not a toy, and is not intended for users under the age of 15. Please use with caution.
- Sharp and potentially dangerous tools are require for assembly. If you are not comfortable handling tools, seek help.
- During operation, certain components may become very hot. Please use caution to avoid potential fires or burns.
- Nitro Engines produce toxic fumes during operation. Only use outside or in a well ventilated area.
- Adult supervision is required for all minors.
RC models should only be used in appropriate environments. Do not use around traffic, people, animals or
any other situations which may cause bodily harm or property damage.
Do not use this model around open flames, ignition sources, rivers, lakes or other sources of water. Do not use this
model during inclement weather (no matter how minor it appears) or around power lines and other utility equipment.
Do not use this model if there are any signs of damage to the transmitter, receiver or battery pack. Discontinue use if
you experience any radio inteference.
WARNING:
RADIOSISTEMI and its affiliates will not be held liable for damages to persons or property as a direct or indirect result
of the improper use of this model or its support equipment. End User assumes ALL risks.
ACCESSORIES::
Required to complete this kit: Engine, Muffler, Transmitter w/ Reciever, (2) Servos, Battery, Starter Box, Glow
Ignitor, Fuel, Fuel Bottle, Polycarbonate Paint, Silicone Diff & Shock Oil.
Hex Tip Drivers
1.5, 2.0, 2.5, 3.0mm
Screwdrivers
Flat Blade
Nut Drivers
5.5, 8.0mm
Pliers
Cutters
Caliper
Wrench
Camber Link
4-Way Drivers Hobby
Knife
Lexan
Scissors
CA Glue
Thread Lock
Silicone Oil
Reamer
We would like to thank you for choosing Radiosistemi products. If you have any assembly or technical questions and
concerns we are available to help. Please email any comments to [email protected] or contact your local distributor.
LOCTITE M3x8 3.5x13 M4x12
M3x4
X2 L
L
R R
X2 02
Apply
Grease
Fill With
Oil
Apply
Thread Lock
Cap
Screw
Button
Screw
Countersunk
Screw
Set
Screw
Washer
Shim
Two
Sided
Quantity Assembly
Step
Note
Attention
0000
It is recommended to use only genuine Radiosistemi accessories and parts for best results.

Differential Assembly
Front & Rear
Shock Absorber Assembly
Front & Rear
X8
Anteriore
Front
x1
Posteriore
Rear
Oil: 7.000 CPS
O-Ring 6x18 Washer
0133008
M3x4
TPSCE3X10ZN
0133009C
0133008C
0133008H
ROND4X10X03
0133008F
ROND6X18X02
0133067
0133008D
STEI3X4
M3x10
TPSCE3X10ZN
X4
X8
Oil Level
x1
Front Oil 500 CPS
Rear Oil 400 CPS
Anteriore
Front
x2
Posteriore
Rear
x2
O-Ring
O-Ring
Bushing
Bushing
0133047A
0133047M
0133091F
0133047H
0133047D
0133047B
0133047L
0133047F
Rear
Rear Front
0133047S 0133091S
ROND7X25X03
0133091A
MA 2,5
X4
0133047N
Front Rear
0133048H 0133049M
0133047U
0133047C
0133047G
0133047P
X4
X2
STEI3X4
M3x4
M3x10
Oil: 2.000 CPS
X4
X2
8x10 Shim
0133047G
0.1MM
0.2MM
0133008G 0133008B
ROND8X10X01
DADO25X38ZB
Front
8X14X4
01
BAG 01
01
BAG 01
ROND6X18X02
ROND4X10X03
ROND8X10X01
GLUE

Differential Bulkhead
Front
CV Axles
Front Rear
0133053A
0133053P
X2
TCCE3X14ZN
0133016
0133020
0133012
0133053R
0133053K
0133053C
0133054A
0133053P
LOCTITE
X1
01
X2
0.5
TCCE3X14ZN
0133013
TCCE3X10ZN
0133020
0.5
STEI4X4
0133016
0133009P
TCCE3X10ZN
0133097
M4x4
X1
M4x4
STEI4X4
X2
X6
TCCE3X14ZN
X2
0133012
M3x14
TCCE3X14ZN
8X16X5
8X16X5
Per prevenire l’ingresso di polvere nella cellula
differenziale, applicare lungo il bordo del grasso.
To prevent fine dust from entering the gearbox,
apply a thin bead of grease along the edge
of the case.
Note: Due to manufacturing tolerances,
you must test fit the bevel and pinion
gears before final assembly. This will
require trial and error, as this can not be
calculated. The gears should not be
shimmed too tight as to create a
resistance or notchy feeling. The gears
must spin smoothly, but also must not
be too loose.
Note: Align the hole in the cover with the
threaded hole on the CV joint. This
allows the cover to remain in place.
M3x14
M3x14
02
BAG 02
02
BAG 02
X2
M3x14
X2
M3x10
X2
M3x10

Front Suspension
0133092E
X8
X2
X2
X4
TCCE3X8ZN
TPSCE3X10ZN
OPTIONAL
M3x8
M5x5
X2
M3x10
X4
X2
L
L
R R
L
L
R R
L
L
R R
L
L
R R
L
L
R R
0133092C
0133092
0133045R
0133044
TCCE3X8ZN
M3x8
X4
0133092A
0133090
0133092D
L
L
R R
STEI4X10
0133022
0133016
STEI5X5
0133035B
0133035P
M5x5
X2
LOCTITE
LOCTITE
STEI3X3
M3x3
X2
0133028T
0133028Z
0133028U
STEI3X10
M3x4
X2
TCCE3X16ZN
M3x16
X2
M3x10
TPSCE3X10ZN
STEI5X5
TCCE3X16ZN
M3x16
X2
M4x10
STEI4X10
LOCTITE
M4x10
L
L
R R
0133045A
X2
X2
0133092B
LOCTITE
0133045
TPSCE3X10ZN
M3x10
X4
0133034
0133028U
X2
0133089
8X16X5
15X21X4
0133031F
OPT.
OPT.
X2
M3x10
STEI3X10
X2
0133035
BAG 03BAG 03
0303
STEI3X3
M3x3
X2

Front End Assembly
65 mm
31 mm.
X4
TCCE2X8ZN
M2x8
X2
L L
R R
TCCE3X30ZN
TPSCE3X8ZN
0133020
0133005
M2x8
X4
LOCTITE
03
02
0133017
0133020
0133030A
0133030D
0.5
0.5
X2
X2
0133020
0133020
0.5
0.5
X2
TCCE3X30ZN
0133030 0133028P
TCCE2X8ZN
Barra.
0133089A
0133089B
0133089C
0133089D
Note: Different Sway Bar Tuning Options
0133072
0133073
0133080
X8
X2 TPSCE4X12ZN
M3x8
M4x12
M4x12
0133079A
0133079C
0133079P
0133079M
0133079G
0133079B
0133019
0133084
0133082
TBCE3X20ZN
0133081
0133079P
0133081A
M3x20
X2
M3x10
X2
M3x20
TBCE3X20ZN
X2
M3x10
X2
TPSCE3X10ZN
05
05
2,3 mm
2.5 mm
2.7 mm
3.0 mm
Note: When installing different diameter
bars you must allow room for bar to
move. Select the appropriate retainer
and adjust screws as needed.
0133082
0133089B
M3x30
M3x30
6X10X3
TPSCE3X10ZN
DADO3X05ZN
M3
X8
TPSCE3X8ZN
M3x8
TPSCE4X12ZN
BAG 04BAG 04
0404
X2
D. 2,5
47 mm
Note: Sway bars
should move freely
throughout entire range
of motion.
0133030D
0133030A
Steering & Ackerman

X2
TCCE3X10ZN
LOCTITE
04
STEI3X10
0133079Z
TPSCE4X10ZN
M4x10
X4
0133027
0133020 0
X2
LOCTITE
X4
TPSCE4X10ZN
M4x10
X2 TPSCE3X10ZN
M3x10
TPSCE3X10ZN
3x10
TBCE3X20ZN
X2
M3x10
X1 STEI3X10
M3x10
X1
0133079U
04
0133079U
0133026
0133043
TBCE3X12ZN X1
DADO3X05ZN
M3x20
0 mm.
X2
M3x8
M3x8
M3x10
X2
M3x10
X2
TCCE3X10ZN
M3x12
TPSCE3X8ZN
TBCE3X12ZN
M3x12
X2
M3
X2
TBCE3X20ZN
X2
M3x20
BAG 05BAG 05
0505
M3x16
TBCE3X16ZN
DADO3X05ZN
M3
TPSCE3X8ZN
Steering Assembly
servo centering point

Front Chassis Brace
Center Differential
Centrale
Central
Oil: 5.000 CPS
Oil Level
x1
TPSCE3X8ZN
M3x8
LOCTITE
X3
TPSCE3X8ZN
M3x8
M3x12
M3x12
X1
X1
TPSCE3X8ZN
M3x8
X2
Note: You can run the brace in flex mode
with the screw turned out, or you can lock
the brace by turning the screw in.
X4
0133064
M3x4
TPSCE3X10ZN
0133071C
ROND4X10X03
0133008C
0133008H
0133008F
ROND6X18X02
0133067
0133008D
STEI3X4
X1
M3x10
TPSCE3X10ZN
X2
X4
X1
M3x4
M3x10
0133003C
LOCTITE
LOCTITE
05
0133003M
TBCE3X12ZN
0133003B
ANE23
0133003
0133003D
0133003A
X1
TBCE3X12ZN
X4
X1
ROND8X10X01
O-Ring
6x18 Shim
8x10 Shim
8X14X4
0.1MM
0.2MM
46T
0133008G
STEI3X4
BAG 06BAG 06
0606
0133008B
ROND6X18X02
ROND8X10X01
ROND4X10X03
GLUE

6,0 mm.
M3x4
X2
LOCTITE
06
GLUE
X4
Note: The front disc brake cover is molded
into the body and requires trimming to
remove the part.
Ream Holes
As Shown
9-10 mm.
X4
TBCE3X16ZN
M3x16
X4
TPSCE3X8ZN
M3x8
X4
TPSCE3X10ZN
M3x10
X2
STEI3X4
M3x4
STEI3X3
M3x3
X2
0133057
0133064F
TBCE3X16ZN
M3x16
X4
0133059
0133059
TPSCE3X8ZN
M3x8
X4
0133062
TPSCE3X10ZN
M3x10
X4
0133050
0133006
0133076A
0133028U
0133077
0133076
0133076
M3x3
X2
LOCTITE
0133074
0133059A
0133028U
5X8X2.5
3X6X2.5
BAG 07BAG 07
0707
Pay careful attention to the direction
and length of the brake arms. The
throttle linkage or carburetor should
not touch the brake arms.
Brake Assembly

Center Assembly
Differential Bulkhead
Rear
TCCE3X14ZN
TBCE3X12ZN
0133012
TPSCE4X10ZN
M4x10
X4
X4
TPSCE4X10ZN
M4x10
06
07
X2
TBCE3X12ZN
M3x12
X2
0133020
0.5
0133020
0.5
TCCE3X30ZN
X2
X2
0133015
01
0133043A
0133025
M3x12
X2
03
STEI4X4
M4x4
X1
0133016
0133012
0133009P
LOCTITE
TCCE3X14ZN
X2
Per prevenire l’ingresso di polvere nella cellula
differenziale, applicare lungo il bordo del grasso.
To prevent fine dust from entering the gearbox,
apply a thin bead of grease along the edge of the case.
Note: Due to manufacturing tolerances, you must test fit the bevel and
pinion gears before final assembly. This will require trial and error, as this
can not be calculated. The gears should not be shimmed too tight as to
create a resistance or notchy feeling. The gears must spin smoothly, but
also must not be too loose.
X4
TCCE3X14ZN
M3x14
X2
TCCE3X30ZN
M3x30
8X16X5
M3x30
M3x14
X2
TCCE3X10ZN
X1
M4x4
STEI4X4
M3x10
M3x14
X2
TCCE3X10ZN
M3x10
08
BAG 08
08
BAG 08

Rear Suspension
30,0 mm.
0133045R
0133020 0
0133024A
X2
M4x10
STEI4X10
L
L
R R
0133045
0133044
0133024B
0133010
0133011
0133032
0133016
0133022
STEI4X10
X2
M4x10
L
L
R R
L
L
R R
0133020 0.5
M3 n.2
0133035
STEI5X5
0133035P
0133035B
X2
M5x5
X2 X2
X2
L
L
R R
X2
L
L
R R
X2
0133030B
0133032D
0133030C
DADOF3X05ZN
M3 n.2
DADOF3X05ZN
X4
DADOF3X05ZN
X2
X2
X2
0133020 0.5
8X16X5
15X21X4
M3
0133045A
X2
M5x5
STEI5X5
L
L
R R
X2
09
BAG 09
09
BAG 09
X2
0133020 0

Rear Assembly
0133089A
0133089B
0133089C
0133089D
Note: Different Sway Bar Tuning Options
2,3 mm
2.5 mm
2.7 mm
3.0 mm
0133020
0.5
0133014
TCCE3X14ZN
0133030A
09
STEI3X3
M3x3
X2
0133028T
0133028U
STEI3X10
M3x10
X2
0133028Z
X2
M3x10
STEI3X10
X2
M3x3
STEI3X3
M3x20
X2
M3x16
X2
TCCE3X16ZN
X2
L
L
R R
08
Barra.
Note: When installing different diameter
bars you must allow room for bar to move.
Select the appropriate retainer
and adjust screws as needed.
X2
TCCE3X14ZN
TCCE3X20ZN
X2
M2x8
X4
TCCE2X8ZN
M3
DADO3X05ZN
X2
X4
TCCE2X8ZN
M2x8
X4
0133020
0.5
0133028P
X2 L
L
R R
10
BAG 10
10
BAG 10
M3x14
TCCE3X20ZN
M3x16
X2
TCCE3X16ZN
M3x14
X2
0133028C
Note: Sway bars should move
freely throughout entire range
of motion.
65mm

Wing Support
Rear Chassis Brace
TCCE3X16ZN
M3x16
X4
0133039
M3x16
X4
10
Note: By using all four holes
you can adjust the angle and
position of the rear wing.
M3x12
X1
TBCE3X12ZN
M3x12
X1
TBCE3X12ZN
0133004B
ANE23
0133003D
0133003
0133303M 0133004A
0133002
LOCTITE
0133003D
ANE23
Note: You can run the brace in flex mode
with the screw turned out, or you can lock
the brace by turning the screw in.
TPSCE3X10ZN
M3x10
X2
X2 TPSCE3X10ZN
M3x10
TCCE3X16ZN
0133039
0133039
11
BAG 11
11
BAG 11
L
R

Rear Assembly
M3x16
X2
TCCE3X16ZN
11
LOCTITE
M3x20
X2
TBCE3X20ZN
X2
TBCE3X20ZN
M3x20
11
DADOF3X05ZN
M3
X2
DADO3X05ZN
M3
X2
X2
DADO3X05ZN
TCCE3X16ZN
M3x16
X2
TPSCE4X10ZN
M4x10
X4
TPSCE3X8ZN
M3x8
X2
TPSCE3X8ZN
TPSCE4X10ZN X4
X2
M4x10
M3x8
08
M3
12
BAG 12
12
BAG 12
X2
DADOF3X05ZN
M3
R
L

Radio Tray
Depending on setup and driver
preference, the battery box can be
placed forwards (as shown) for more
steering or backwards for more
rear grip.
If a switch is to be used, cut along
the marked lines inside of the
receiver box lid. Use a rubber
shield to protect the swtich.
M3x8
X3
TBCE3X8ZN
X8
TBCE3X16ZN
M3x16
DADO3X05ZN
M3
X3
X4
TPSCE3X8ZN
M3x8
X3
TPSCE3X10ZN
M3x10
TPSCE3X8ZN
M3x8
X4
0133055
0133049
0133056
TPSCE3X10ZN
M3x10
X3
TPSCE3X12ZN
M3x12
X2
0133052
0133052
Receiver
(Not Included)
Battery
(Not Included)
Servos
(Not Included)
M3x12
X8
TBCE3X16ZN
0133052
0133052
0133058
M3x10
X3
TBCE3X10ZN
TPSCE3X10ZN
M3x10
X1
GLUE
X4
TBCE3X10ZN
M3x10
X1
TPSCE3X10ZN
M3x10
Position servo leads in cutouts to prevent wire damage.
X3
TBCE3X8ZN
M3x8
13
BAG 13
13
BAG 13
M3x10
X1
TBCE3X10ZN
TBCE3X10ZN
M3x10
X1
0133051

Radio Tray & Linkages
Use the appropriate servo
horn to match the number of
teeth on your servos.
X6
TPSCE3X10ZN
M3x10
M3x8
X2
TBCE3X8ZN
X2
TBCE3X8ZN
M3x8
TPSCE3X10ZN
M3x10
X6
12
13
X1
X1
X1
n° 25 Futaba,
savox, ecc.
n° 23 KO Propo,
ecc.
n° 24 Hitec,
sanwa, ecc.
LOCTITE
0133036
M2,5x10
X2
TCCE25X10ZN
X2
TCCE25X10
M2,5x10
X2
LOCTITE
X3
M3x3
STEI3X3
15
0133037
0133076
14
BAG 14
14
BAG 14
THROTTLE & BRAKE LINKAGE SET 0133023
STEI3X3
M3x3
X3
M3x12
X1
TBCE3X12ZN
X1
TBCE3X12ZN
M3x12
DADO3X05ZN
M3
X1

Clutch & Engine Assembly
Engine & Fuel Tank
Note: Graphics were simplified
for clarified view of components
to be assembled.
DO NOT disassemble kit!
14
M3x14
X4
TCCE3X14ZN
ROND7X14X03
LOCTITE
X4
X4
TCCE3X14ZN
M3x14
X4
M3x8
X1
0133069
0133069D
0133068
0133087B
ROND5X12X01
ROND5X12X02
M3x8
X1
TCCE3X8ZN
Note: The number and location of shims will vary based
on type and model of engine used. Aim for 0.2-0.3mm of
end play.
The pinion might differ from that shown.
Engine (Not Included)
Note: To help
facilitate a proper
gear mesh between
the spur and pinion,
it is recommended to
use a strip of paper
and place it between
the gears before
tightening down the
engine mount
screws.
Tuned Pipe (Not Included)
LOCTITE
0133094
0133096
0133096
LOCTITE
TPSCE4X10ZN
M4x10
X1
TPEI5X12ZN
X4
TPSCE4X10ZN
M4x10
X2
0133098
TBCE3X12ZN
M3x12
X2
X2
M3x12
X4
TPEI5X12ZN
X3
TPSCE4X10ZN
M4x10
M5x12
14z
15
BAG 15
15
BAG 15
TCCE3X8ZN
0133018
ROND5X12X01
ROND5X12X02
ROND7X14X03
ROND5X12X01
TBCE3X12ZN
X1
M4x4
STEI4X4
STEI4X4
M4x4
M5x12
ROND8x12x02
5x10x4
X4
ROND5X12X02
ROND8X12X02 X4
0133093
NOTE: Attach fuel line clips before
installing fuel tank.

Final Assembly
Rear
Front
Ream
Mounting Holes
Trim with
Lexan
Scissors
Rear
01
L
L
R R
X2
TCCE3X20ZN
X2
Expanded View
TCCE3X20ZN
X2
Expanded View Front
Carburetor
Zip Ties
01
M3x14
X2
TCCE3X14ZN
0133029
0133021
0133021
M3 n.2
X2
DADO3X05ZN
0133097A
0133041A
0133041
DADO3X05ZN
TCCE3X25ZN
M3x25
X2
L
L
R R
X2
M3 n.2
X2
01
0133041
0133097A
DADO3X05ZN
TCCE3X25ZN
M3x25
X2
L
L
R R
X2
0133041A
0133060
0133060S
0133060K
Note: Use only
polycarbonate safe paint.
0133095
0133060K
X2
TCCE3X14ZN
M3x14
X6
DADO3X05ZN
M3
AIR FILTER SET:
0133060S
X4
M3x25
TCCE3X25ZN
M3 n.2
X2
L
L
R R
X2
01
X4
16
BAG 16
16
BAG 16
TCCE3X20ZN
M3x20
M3x20
M3x20

Parts Listing
0133002
0133003
0133003A
0133003B
0133003C
0133003D
0133003M
0133004A
0133004B
0133005
0133006
0133008
0133008B
0133008C
0133008D
0133008F
0133008G
0133008H
0133009C
0133009P
0133010
0133011
0133012
0133013
0133014
0133015
0133016
0133017
0133018
0133019
0133020
0133021
0133022
0133023
0133024A
0133024B
0133025
0133026
0133027
0133028C
0133028P
0133028T
0133028U
0133028Z
0133029
0133030
0133030A
0133030B
0133030C
0133030D
Rear Brace Mount
Brace Mount (Lower)
Front Brace Upper
Front Brace Lower
Front Brace Mount (Upper)
Brace Crosspin
Brace Spring
Rear Brace Upper
Rear Lower Brace
Front Bumper
Center Diff Plate
Center Outdrive Set (2)
Differential Housing
Differential Spider Gear Set (6)
Differential Cross Shaft Set (2)
Differential Gasket Set (3)
Differential Internal Crosspin (10)
Differential O-Ring Set (10)
Differential Helical Bevel Gear (43T)
Input Pinion Gear (13T)
Rod End Set (Rear)
Turnbuckle (Rear)
Differential Bulkhead
Suspension Block (FR)
Suspension Block (RR)
Suspension Block (RF)
8x16x5 Bearing
Suspension Block (FF)
Engine Mount Set (2)
Pivot Ball (Steering) (2)
Suspension Bushing Inserts
Rear Wing (Black)
15x21x4 Bearing (10)
Thottle/Brake Linkage Set
Pivot Ball (Rear, Inner) (2)
Pivot Ball (Rear, Outer) (2)
Shock Tower (Rear)
Upper Ackerman Plate
Suspension Block (UF)
Sway Bar (Rear, 2.7mm)
Sway Bar Retainer Set
Pivot Ball (Anti-Sway, Upper) (4)
Rod End Set (Short) (4)
Pivot Ball (Anti-Sway, Lower) (4)
Body Clips (10)
Adjustment Clip Set (14)
Hinge Pin (F/R, Inner) (4)
Hinge Pin (Rear, Outer) (2)
Hinge Pin (Camber Link) (2)
Hinge Pin (Front, Upper) (2)
0133031F
0133031R
0133032
0133032D
0133034
0133035
0133035B
0133035P
0133036
0133037
0133039
0133040C
0133040W
0133041
0133041A
0133042
0133043
0133043A
0133044
0133045
0133045A
0133045R
0133047A
0133047B
0133047C
0133047D
0133047E
0133047F
0133047G
0133047H
0133047L
0133047M
0133047N
0133047P
0133047S
0133047U
0133047Z
0133048M
0133049
0133049M
0133050
0133051
0133052
0133053A
0133053C
0133053K
0133053P
0133053R
0133054A
0133055
Suspension Arm (Front, Lower) (2)
Suspension Arm (Rear) (2)
Rear Hub Carrier Set
Lower Hub Spacer Set
Suspension Arm Set (Front, Upper)
Wheel Hex (Lightened) (2)
Wheel Nut (Lightened) (2)
M3x17 Pin Set (4)
Throttle Servo Arm Set
Steering Servo Arm Set
Rear Wing Mount
RR8 Decal Set
RR8 Wing Decal Set
Shock Mount (4)
Shock Mount Bushing (4)
Shock Springs (4)
Body Post (Front)
Body Post (Rear)
Wheel Axle (2)
CV Driveshaft (Outboard) (2)
CV-Joint Pin Set (4)
CV-Joint Coupler Barrel
Shock Cap (2)
Shock Seal Bushing (Lower) (4)
Pivot Ball (Shock, Lower) (2)
Shock Seal Bushing (Middle) (4)
Spring Adjust Nut O-Ring (4)
Shock Body (Rear) (2)
Spring Adjust Nut (2)
Shock O-Ring Set (8)
Lower Shock Cap (2)
Shock Bladder Set (4)
Shock Boot Set (4)
Spring Retaining Collar (4)
Shock Shaft (Rear) (2)
Rod End Set (Shock) (4)
—
Front Spring Set (Medium) (2)
Servo Mount Set (4)
Rear Spring Set (Medium) (2)
5x8x2.5 Flanged Bearing (2)
Rubber Switch Cover
Receiver & Battery Box Set
Center CV Driveshaft (Front)
CV Joint Retaining Cover
CV Joint
CV Joint Pin Set (Center) (10)
CV Joint Coupler Barrel (Center)
Center CV Driveshaft (Rear)
Aluminum Servo Tray

Parts Listing
0133056
0133057
0133058
0133059
0133059A
0133060
0133060K
0133060S
0133062
0133064
0133064F
0133067
0133068
0133069
0133069A
0133069B
0133069C
0133069D
0133069E
0133069F
0133071C
0133072
0133073
0133074
0133076
0133076A
0133077
0133079A
0133079B
0133079C
0133079G
0133079M
0133079P
0133079U
0133079Z
0133080
0133081
0133081A
0133082
0133084
0133087B
0133089
0133089B
0133090
0133091A
0133091F
0133091S
0133092
0133092A
0133092B
Servo Tray Support Set (4)
Brake Metal Backing Pad Set (4)
Antenna Tube
Center Diff Mount & Guides Set
3x6x2.5 Bearing (2)
Low Profile Air Filter Set
Air Filter & Boot
Air Filter Element Set (6)
Brake Rotor (2)
Outdrives (Center) (2)
Brake Pad Set (4)
8x14 Bearing
5x10x4 Bearing (2)
Adjustable Clutch Assembly
Flywheel
Aluminum Clutch Shoe Set (3)
Carbon Clutch Shoe Set (3)
Clutch Nut
Clutch Springs (3)
Flywheel Adjustment Cap
Lightened Spur Gear (46T)
Side Guard Set
3mm Main Chassis
Brake Cam (2)
Brake Lever Arm Set (2)
Pivot Ball (Brake) (2)
Turnbuckle (Brake)
6x10x3 Bearing (4)
Servo Saver O-Ring (10)
Servo Saver Tube
Servo Saver Spring Nut
Servo Saver Spring
Steering Ackerman Plastic Set
Rod End Set (Servo) (2)
Pivot Ball Set (Servo) (2)
Steering Post (2)
Ackerman Plate
Ackerman Retainer Nut (2)
Rod End Set (Steering) (4)
Turnbuckle (Steering) (2)
Clutchbell (14T)
Pivot Ball Stud (Lower) (2)
Sway Bar (Front, 2.5mm)
Pivot Ball Stud (Upper) (2)
Shock Piston (6 x 1.3mm) (4)
Shock Body (Front) (2)
Shock Shaft (Front) (2)
Front Steering Knuckle Set (2)
Pivot Ball (4)
Pivot Ball Retaining Nut (4)
0133092C
0133092D
0133093
0133094
0133095
0133096
0133097
0133097A
0133098
ANE23
DADO25X38ZB
DADO3X05ZN
DADOF3X05ZN
ROND4X10X03
ROND5X12X01
ROND6X18X02
ROND7X14X03
ROND7X25X03
ROND8X10X01
STEI3X10
STEI3X3
STEI3X4
STEI4X10
STEI4X4
STEI5X5
TBCE3X10ZN
TBCE3X12ZN
TBCE3X16ZN
TBCE3X18ZN
TBCE3X20ZN
TCCE2X8ZN
TCCE3X10ZN
TCCE3X12ZN
TCCE3X14ZN
TCCE3X16ZN
TCCE3X20ZN
TCCE3X25ZN
TCCE3X30ZN
TCCE3X8ZN
TPEI5X12ZN
TPSCE3X10ZN
TPSCE3X12ZN
TPSCE3X8ZN
TPSCE4X10ZN
TPSCE4X12ZN
Knuckle Steering Arm (2)
Pivot Ball Bushing Set (4)
Pipe Mount
Pipe Wire
Bittydesigns Body (RR8)
Tank Mounts
Shock Tower (Front)
Shock Retaining Washer (4)
Fuel Tank (125cc)
Circlip (10)
M2.5 Locknut (10)
M3 Locknut (10)
M3 Flanged Locknut (10)
4x10 Shim (0.3) (10)
5x12 Shim (0.1) (10)
6x18 Shim (0.2) (10)
7x14 Washer (0.3) (10)
7x2.5 Washer (0.3) (10)
8x10 Shim (0.1) (10)
M3x10 Set Screw (10)
M3x3 Set Screw (10)
M3x4 Set Screw (10)
M4x10 Set Screw (10)
M4x4 Set Screw (10)
M5x5 Set Screw (10)
M3x10 Button Screw (10)
M3x12 Button Screw (10)
M3x15 Button Screw (10)
M3x18 Button Screw (10)
M3x20 Button Screw (10)
M2x8 Cap Screw (10)
M3x10 Cap Screw (10)
M3x12 Cap Screw (10)
M3x14 Cap Screw (10)
M3x16 Cap Screw (10)
M3X20 Cap Screw (10)
M3x25 Cap Screw (10)
M3x30 Cap Screw (10)
M3x8 Cap Screw (10)
M5x12 Engine Screw (10)
M3x10 Countersunk Screw (10)
M3x12 Countersunk Screw (10)
M3x8 Countersunk Screw (10)
M4x10 Countersunk Screw (10)
M4x12 Countersunk Screw (10)