Rain Bird ESP-RZ User manual

English
Rain+Birdt
ESP-RZ Controller
Installation Guide and Operations Manual
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
AM
MD
YYYY

II
Contents
Introduction
Welcome to Rain Bird ...................................... 1
Controller Features ......................................... 1
Controls and Indicators................................... 1
Key Functions..................................................................... 1
Normal Operation
Auto ................................................................. 2
Off .................................................................... 2
Basic Programming
Date/Time ........................................................ 2
Zone Schedule ................................................. 3
Select Zone .........................................................................3
Set Watering Run Times ................................................3
Set Watering Start Times............................................... 3
Set Watering Start Days.................................................4
Custom Days ..................................................................4
Odd Days .........................................................................4
Even Days......................................................................... 4
Cyclic Days.......................................................................4
Additional Features
Manual Watering ............................................. 5
Water ALL Zones:.............................................................. 5
Water ONE Zone:..............................................................6
Seasonal Adjust............................................... 6
Installation
Indoor Model................................................... 7
Mount Controller..............................................................7
Connect Power..................................................................7
Wiring Connections......................................... 8
Connect Zone Valves...................................................... 8
Connect Master Valve ....................................................8
Connect Pump Start Relay...........................................9
Connect Rain Sensor ......................................................9
Options and Special Features
Install Batteries ............................................. 10
Reset Button .................................................. 10
Rain Sensor Bypass ....................................... 10
Set Bypass for All Zones............................................. 10
Troubleshooting
Error Detection.............................................. 11
Watering Issues ............................................. 11
Electrical Issues ............................................. 11
Programming Chart............................. 12
Rain+Birdt
ESP-RZ Controller
Installation Guide and Operations Manual

ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
AM
MD
YYYY
1
Introduction
Welcome to Rain Bird
Thank you for choosing the ESP-RZ Controller from
Rain Bird.
For more than seven decades, Rain Bird has led the irrigation
industry by providing the highest quality products and
services available for state of the art water management.
ESP-RZ Controller
Your new Rain Bird controller is designed to provide
many years of advanced irrigation control.
In this manual are step by step instructions for how to
install and operate your ESP-RZ Controller.
Display Screen
Displays programming
information and active
irrigation status.
Next/Back Keys
Select programming
options.
Off
Cancel all active watering
immediately and disable
automatic irrigation.
Seasonal Adjust
Increase or decrease
watering duration (Run
Times) for all Zones.
Manual Watering
Start watering
immediately for all Zones
or for any single Zone.
Zone Schedule
Create customized
irrigation schedules to
run automatically at
specic times, durations
and intervals.
Auto
Watering occurs automatically
according to programmed irrigation
schedules.
Controller Features
The ESP-RZ controller has a variety of advanced water
management features, including:
 Zone based programming allows independent
irrigation scheduling for dierent areas (Zones), based
on the specic water requirements for each area.
 Programs can be set to water on selected days of
the week, odd or even calendar days, or at custom
intervals, allowing enhanced exibility and control of
irrigation schedules.
 Multiple Watering Start Times allow you to run the
same program multiple times on the same day.
 Seasonal Adjust allows quick adjustment of watering
duration based on weather or other conditions.
 Manual Water feature to allow immediate watering of
all Zones or else one Zone at a time.
Controls and Indicators
The easy to program user interface allows quick and
efficient setup of customized irrigation schedules.
Key Functions
Date/Time
Set the current calendar
Date and Time of day.
 NOTE: Press and
HOLD + or –to
accelerate setting
adjustments.
+or –Keys
Adust program settings.

2
Normal Operation
AUTO Auto
Watering occurs automatically according to
programmed irrigation schedules.
Press the AUTO key to resume normal operation
whenever programming is completed and to
monitor active watering.
 NOTE: Unless the OFF key is pressed, the
controller will revert to AUTO mode by default
after 10 minutes, if no programming activity
(key presses) occurs during that time.
In Auto Mode:
The display shows the current time, date and day of
the week:
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
MD
YYYY
PM
During Watering:
The display shows a blinking sprinkler symbol,
the active Zone number and watering Run Time
remaining for that Zone.
Z
O
N
E
MIN
BACK OFF ON NEXT
Zone
Run
Time
Press +or –to adjust watering Run Time
remaining for the active Zone as desired.
Press NEXT to immediately cancel watering for
the active Zone and advance to the next Zone in
the irrigation queue.
OFF Off
Cancel all active watering immediately and
disable automatic irrigation.
Press the OFF key to immediately cancel all
active watering.
BACK OFF ON NEXT
Programmed irrigation schedules remain stored in
memory even when the controller is turned o or if
power is lost.
 NOTE: Press the AUTO key to resume normal
operation. Automatic irrigation will NOT occur if
the controller remains in OFF mode.
Basic Programming
DATE/TIME
Date/Time
Set the current calendar Date and Time of day.
Press the DATE/TIME key.
Press +or –to set the month (M); then press
NEXT to select and set the day (D), then year
(YYYY).
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
MD
YYYY
AM
BACK OFF ON NEXT
DATE

3
Press +or –to set the hour (ensuring that AM/
PM setting is correct); then press NEXT to select
and set the minutes.
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
MD
YYYY
AM
BACK OFF ON NEXT
TIME
 NOTE: Two AAA batteries can be installed to
retain date and time in the event of a power
outage. See“Install Batteries”for details.
SCHEDULE Zone Schedule
Create customized irrigation schedules to run
automatically at specific times, durations and
intervals.
Press the ZONE SCHEDULE key.
1 Select Zone
Zones are designated areas (for example,
“Rose Garden”) that you define as locations for
watering. See “Programming Chart” for details.
Press +or –to select the desired Zone Number;
then press NEXT.
Z
O
N
E
1
2
MIN
BACK OFF ON NEXT
Zone
2 Set Watering Run Times
Watering Run Times are durations (for example,
20 minutes) set for watering.
 NOTE: Run Times can be set between 1 to 199
minutes.
Press +or –to set the desired Run Time (MIN);
then press NEXT.
Z
O
N
E
MIN
1
2
BACK OFF ON NEXT
RUN
TIME
3 Set Watering Start Times
Watering Start Times are times of day at which
watering is set to begin.
 NOTE: A total of up to four Start Times (1-4) are
available for each Zone.
Press +or –to set the 1st Start Time (ensuring
that AM/PM setting is correct); then press NEXT.
 NOTE: Start Time adjustments are set in 10
minute increments.
Z
O
N
E
1
2
MIN
BACK OFF ON NEXT
START
TIME
 REPEAT as desired to set additional Start Times
for that Zone.
 NOTE: Pressing NEXT when -:- (OFF) is
blinking on the display will advance to Step 4.

4
4 Set Watering Start Days
Watering Start Days are the calendar days or
intervals (for example, Monday, Wednesday and
Friday) on which watering is allowed.
Press +or –to select one of four available
Watering Start Day options:
a. Custom Days - To schedule watering to occur
on selected days of the week, go to 4a.
b. Odd Days - To schedule watering to occur on all
odd calendar days (1,3,5...29 etc.), go to 4b.
c. Even Days - To schedule watering to occur on
all even calendar days (2,4,6...30 etc.), go to 4c.
d. Cyclic Days - To schedule watering to occur at
intervals (every 2 days, or 3 days, etc.), go to 4d.
4a Custom Days
Press +or –to select then press NEXT
Z
O
N
E
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
AM
1
2
MIN
BACK OFF ON NEXT
Press ON (to enable) or OFF (to disable) the
blinking Selection Day. Cursor will then advance
to the next Selection Day.
Z
O
N
E
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
AM
1
2
MIN
BACK OFF ON NEXT
SELECTION
DAY
 Press ON or OFF to set each subsequent day of
the week as desired.
4b Odd Days
Press +or –to select
135
29
,,...
then press
NEXT
Z
O
N
E
AM
1
2
MIN
135 29,,...
BACK OFF ON NEXT
4c Even Days
Press +or –to select
246 30,,...
then press
NEXT
Z
O
N
E
246 30,,...
AM
1
2
MIN
BACK OFF ON NEXT
4d Cyclic Days
Press +or –to select then press NEXT
Z
O
N
E
EVERY
DAYS,STARTINGAM
1
2
MIN
MD
YYYY
BACK OFF ON NEXT

5
Press +or –key to set the desired Day Cycle;
then press NEXT.
Z
O
N
E
BACK OFF ON NEXT
EVERY
AM
1
2
MIN
MD
YYYY
DAYS,STARTING
DAY
CYCLE
Press +or –to set desired Start Date;
then press NEXT.
Z
O
N
E
EVERY
AM
1
2
MIN
DAYS,STARTING
MD
YYYY
BACK OFF ON NEXT
START
DATE
 NOTE: The Start Date can only be set to occur
within the current day cycle. The display will
always update to show the next scheduled
irrigation day.
THEN
 REPEAT steps 1-4 for additional Zones as
desired.
Additional Features
MANUAL Manual Watering
Start watering immediately for ALL Zones or for
any ONE Zone.
Water ALL Zones:
Press the MANUAL WATERING key.
ALL Zones appears as the default selection;
press NEXT to continue.
Z
O
N
E
MIN
BACK OFF ON NEXT
ALL
ZONES
Press +or –to set the desired Run Time; then
press NEXT to begin watering.
Z
O
N
E
BACK OFF ON NEXT
MIN
RUN
TIME
During Manual Watering:
Press +or –to adjust watering Run Time
remaining for the active Zone as desired.
Press NEXT to immediately cancel watering for
the active Zone and advance to the next Zone in
the irrigation queue.

6
Water ONE Zone:
Press the MANUAL WATERING key.
Press +or –to select any ONE Zone; then press
NEXT.
Z
O
N
E
MIN
BACK OFF ON NEXT
ZONE
Press +or –to set the desired Run Time; then
press NEXT to begin watering.
Z
O
N
E
BACK OFF ON NEXT
MIN
RUN
TIME
During Manual Watering:
Press +or –to adjust watering Run Time
remaining for the active Zone as desired.
SEASONAL
ADJUST
Seasonal Adjust
Increase or decrease watering duration (Run
Times) for all Zones.
Press the SEASONAL ADJUST key.
Press +or –to increase or decrease the
SEASONAL ADJUST percentage setting.
 NOTE: The SEASONAL ADJUST value can be
adjusted from -90% to +100%. For example,
a +50% adjustment means a Run Time of 10
minutes will become 15 minutes.
BACK OFF ON NEXT
SETTING
 NOTE: SEASONAL ADJUST applies to ALL
programmed irrigation schedules.

7
Installation
Indoor Model
Mount Controller
Choose a suitable mounting location on an
indoor wall within 6 feet (1.8 meters) of a
grounded electrical outet. Allow clearance for
conduit connections below the unit
3 IN.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
6 FEET
MAX.
 NOTE: DO NOT use an outlet that is controlled
by a secondary ON/OFF light switch or GFI
outlet.
Grasp the two handles on either side of the
wiring bay cover and pull it towards you to
remove it.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
Drive a mounting screw into the wall. Leave an
1/8 inch gap between the screw head and the
wall surface.
 NOTE: If necesssary, use the provided anchors
to assure that screws can be tightened securely.
Locate the keyhole slot on back of the controller
unit and hang the unit securely on the mounting
screw.
1/8 IN.
KEYHOLE
Drive a second mounting screw through the
open hole inside the wiring bay and into the
wall. Verify that the unit is fastened securely to
the wall.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
Connect Power
Route the transformer power cord through the
conduit opening at the bottom of the unit.
Connect the two end wires on the power cord
to the two 24VAC terminal connections on the
controller.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
Plug the transformer into the electrical outlet.
 WARNING: DO NOT plug in the transformer
until you have completed and checked all wiring
connections.

8
 NOTE: This appliance is not intended for use
by persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
 WARNING: If the supply cord of an outdoor
controller is damaged, it must be replaced by
a special cord or assembly available from the
manufacturer or its service agent.
If the supply cord of an indoor controller
is damaged, it must be replaced by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
Wiring Connections
Connect the valve wires for each Zone and for
(optional) Master Valve, Pump Start Relay or Rain
Sensor.
 NOTE: If installing an outdoor model, route
all eld wires through conduit or through the
knock-out on back of the unit.
Connect Zone Valves
Connect the power wire from each Zone valve
to the corresponding Zone number on the
controller terminal block.
Connect the common wire from each valve to
the COMMON (C) terminal.
ZONE 1
VALVE
POWER
COMMON
ZONE 2
VALVE
ETC.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
Connect Master Valve
Connect an optional Master Valve to the ESP-RZ
controller.
Connect the power wire from the master valve
to the master (M) terminal on the controller
terminal block.
Connect the common wire from the master
valve to the COMMON (C) terminal.
COMMON
MASTER
VALVE
POWER
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET

9
Connect Rain Sensor
Connect an optional rain sensor to the ESP-RZ
controller.
On the terminal board, remove the jumper wire
from the SENS terminals.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
Connect both Rain Sensor wires to the SENS
terminals.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
Connect Pump Start Relay
Connect an optional Pump Start Relay to the ESP-
RZ controller.
Pumps are used in some places to draw water from a
well or other source. If you are activating a pump from
the controller, you must install a pump start relay.
A pump start relay connects to the controller in the
same way as a Master Valve, but connects dierently
at the water source.
 NOTE: the ESP-RZ controller DOES NOT provide
main power for a pump.
Connect the Relay Input wire from the pump
start relay to the master (M) terminal on the
controller terminal block.
PUMP
START
RELAY
COMMON
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS12345678CM
RESET
FIELD
COMMON
RELAY
INPUT
Connect the common wire from the pump start
relay to the COMMON (C) terminal.
 NOTE: To avoid possible pump damage when
using a pump start relay, connect a short jumper
wire from any unused Zone terminal(s) to the
nearest Zone terminal in use.
For example, if a 4 Zone controller model is in
use with only two Zones connected, route the
terminals for Zones 3 and 4 to the nearest active
terminal (in this example, Zone 2)

10
Options and Special
Features
Install Batteries
The ESP-RZ can keep Date and Time if batteries
are installed for backup.
 NOTE: Your programming is stored in Non-
Volatile memory and will remain in the controller
even if batteries are not installed.
Insert two AAA batteries into the battery slot
above the terminal block, as shown below.
REMOTE
24VAC SENS12345678CM
ACCESSORY
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
Reset Button
If the controller is not working properly, you can
try pressing RESET.
 NOTE: All previously programmed watering
schedules will remain stored in memory, but the
current Date/Time will need to be set again.
Insert a small tool such as a paper clip, into the
access hole and press until the controller is reset.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
REMOTE
24VAC
ACCESSORY
SENS 12345678CM
RESET
Rain Sensor Bypass
The controller can be set manually to either OBEY
or IGNORE a Rain Sensor.
 NOTE: Rain Sensor Bypass settings cannot be
changed while the controller is irrigating.
Set Bypass for All Zones
Press the AUTO key.
Press and release both BACK and NEXT keys
at the same time to toggle between OBEY and
IGNORE.
ESP-RZ
Z
O
N
E
OFF
AUTO
T
2
W
3
TH
4
F
5
S
6
SU
7
M
1
DATE/TIME
SCHEDULE
MANUAL
SEASONAL
ADJUST
BACK OFF ON NEXT
The NO RAIN SENSOR symbol will show on the
display when IGNORE is selected.

11
Troubleshooting
Error Detection
The ESP-RZ controller has a built-in error detection that
senses a electrical short circuit or overload condition on a
Zone’s output line.
In the event of an error condition, the following steps
take place regarding the error:
 The aected Zone number and “Err” alert message will
show on the display when the unit is in either AUTO or
MANUAL WATERING mode.
Watering Issues
Problem Possible Cause Possible Solution
Programmed schedules
and manual watering
functions do not start.
Water source not supplying water. Verify there is no disruption to the main water line
and that all other water supply lines are open and
functioning properly.
Wiring is loose or not properly
connected.
Check that eld wiring and master valve or pump start
relay wiring is securely connected at the controller and
in the eld.
Field wires are corroded or
damaged.
Check eld wiring for damage and replace if necessary.
Check wiring connections and replace with watertight
splice connectors if needed.
Connected rain sensor may be
activated.
Let the rain sensor dry out or else disconnect it from the
controller terminal block and replace it with a jumper
wire connecting the two SENS terminals.
Jumper wire connecting the two
SENS terminals on the terminal
block may be missing or damaged.
Jumper the two SENS terminals on the controller
terminal block by connecting them with a short length
of 14 to 18 gauge wire.
Electrical Issues
Problem Possible Cause Possible Solution
Display is blank. Power not reaching the controller. Verify the main AC power supply is securely plugged in
or connected and working properly.
Display is frozen and
controller will not accept
programming.
An electrical surge may have
interferred with the controller’s
electronics.
Unplug the controller for 2 minutes, then plug it back in.
If there is no permanent damage, the controller should
accept programming and resume normal operation.
 All irrigation for the aected Zone is cancelled and
watering advances to the next operable Zone in the
irrigation queue.
 NOTE: The controller will attempt to water the
aected Zone again at the next scheduled watering.
Completion of a successful watering will clear the
error condition associated with that Zone.

12
Enter the Watering Run Time for that Zone.
Enter Watering Start Times (up to four total).
Select Watering Start Days (checkbox). If Custom
Days is selected, circle the days of the week to water.
If Cyclic Days is selected, enter a number from 1-14.
Zone Zone Description Watering
Run Time Watering Start Times Watering Start Days
1________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
2________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
3________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
4________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
5________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
6________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
7________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
8________
MIN.
1 ____ : ____ AM PM
2 ____ : ____ AM PM
3 ____ : ____ AM PM
4 ____ : ____ AM PM
Custom Days
M T W T F SA SU
Odd Days Even Days
Cyclic Days every ____ days
Programming Chart
Before programming your controller, plan the watering
schedule for each Zone using the Programming Chart and
keep it for reference.
In the Zone Description column, enter a brief
description such as “front lawn” or “side yard”.

English
27JL12 P/N: 640252-01
Rain+Birdt
Rain Bird Corporation
6991 East Southpoint Road
Tucson, AZ 85756
USA
Tel: [phone]
Fax: [phone]
Rain Bird International
1000 West Sierra Madre Avenue
Azusa, CA 91702
USA
Tel: [phone]
Fax: [phone]
Rain Bird Europe SNC
900, rue Ampère, B.P. 72000
13792 Aix en Provence Cedex 3
FRANCE
Tel: [phone]
Fax: [phone]
Rain Bird France SNC
900, rue Ampère, B.P. 72000
13792 Aix en Provence Cedex 3
FRANCE
Tel: [phone]
Fax: [phone]
Rain Bird Ibérica. S.A.
Polígono Ind. Pinares Llanos
C/ Carpinteros, 12, 2ºC
28670 Villaviciosa de Odón, Madrid
ESPAÑA
Tel: [phone]
Fax: [phone]
Rain Bird Desutschland GmbH
Oberjesinger Str. 53
71083 Herrenberg-Kuppingen
DEUTSCHLAND
Tel: [phone]
Fax: [phone]
Rain Bird Sverige AB
Fleningevägen 315
254 77 Fleninge
SWEDEN
Tel: [phone]
Fax : [phone]
Rain Bird Turkey
İstiklal Mahallesi,
Alemdağ Caddesi, No.262
34760 Ümraniye İstanbul
TÜRKİYE
Tel: [phone]
Fax: [phone]
2012 Rain Bird Corporation
tRegistered trademark of Rain Bird Corporation
www.rainbird.com
www.rainbird.eu