Rain Bird ESP-SMTe User manual

Rain+Birdt
ESP-SMTe Controller User Manual
AUTO MODE
Monday 02 May 2016
05:00 PM
Next
Irrigation
Estimate 05 May
Now with both
Simple Smart Programming
and
Advanced ET Watering Features
Introduction
Welcome to Rain Bird
Thank you for choosing the ESP-SMTe Smart Modular Con-
trol System from Rain Bird. The ESP-SMTe is an indoor or
outdoor weather-based irrigation controller. Two ESP-SMTe
models are available that can be expanded up to 22 sta-
tions by adding optional station modules:
• 4 Station Indoor Controller (ESP4SMTei)
• 4 Station Outdoor Controller (ESP4SMTe)
The Intelligent Use of Water®
We believe it is our responsibility to develop products that
use water eciently.
ESP-SMTe Controller Features
The ESP-SMTe has two programming mode options that
make watering adjustments based on inputs from the
weather sensor.
Simple Smart Mode
In Simple Smart mode, the ESP-SMTe acts like a tradi-
tional time-based controller. Watering is scheduled on
specic days, with xed start times and run times. Auto-
matic adjustments are made to run times based on current
weather conditions.
Advanced ET Mode
In Advanced ET mode, the ESP-SMTe uses state of the
art technology to determine water needs for each zone
to ensure optimal landscape health with minimal water
usage. Advanced mode will change the irrigation schedule
daily based on water needs.
Time-Based Controller Water Use
Water
Savings
Winter Spring Summer Fall
ESP-SMTe Controller Water Use

ESP-SMTe Controller
2
Technical Support
Questions?
For help setting up and operating
the Rain Bird ESP-SMTe Controller,
scan the QR code to visit
www.rainbird.com/espsmte
Additional user documentation is
available under the Manuals & Literature tab, including:
• User Manual (this document)
• Contractor’s Manual (full operations manual)
• Interactive Site Prole Chart
• Foreign Language Support
To learn more about Rain Bird irrigation systems and our-
Rain Bird Academy training programs, visit:
www.rainbirdservices.com/training
To see instructional videos for the ESP-STMe, visit
www.youtube.com/
Or call Rain Bird toll free Technical Support at
1-800-724-6247 (USA and Canada only)
Introduction
Welcome to Rain Bird................................................... 1
The Intelligent Use of Water® .........................................1
ESP-SMTe Controller Features .................................... 1
Simple Smart Mode ...........................................................1
Advanced ET Mode............................................................1
Technical Support......................................................... 2
Installation
Mount Controller .......................................................... 3
Wiring Connections...................................................... 3
Connect Valves ....................................................................3
Connect Master Valve (optional)...................................3
Connect Pump Start Relay (optional)..........................4
Connect Power ....................................................................4
Station Expansion Modules........................................ 5
Install Modules ....................................................................5
Station Numbering ............................................................6
Module Conguration ......................................................6
Connect Weather Sensor Wire to Controller............ 6
Complete Controller Installation............................... 6
Weather Sensor Installation ....................................... 7
Choose Location ................................................................7
Sensor Mounting Options ...............................................7
Mount Weather Sensor.....................................................8
Connect Weather Sensor Wire .......................................8
Normal Operation
Controls and Indicators ............................................... 9
Weather Sensor Features ............................................ 9
Operating Modes........................................................10
AUTO RUN .......................................................................... 10
OFF........................................................................................ 10
Simple Smart Programming
Set Date and Time....................................................... 11
Congure Controller .................................................. 11
Set Site Info........................................................................ 11
Set Schedule...................................................................... 12
Review Settings................................................................ 13
Input Zone Information............................................. 14
Set Zone Run Times ........................................................ 14
Set Grow-In Schedule..................................................... 14
Special Features .......................................................... 15
Event Days O................................................................... 15
Short Circuit Test.............................................................. 15
Advanced Controller Setup.......................................... 15
Select Programming Mode.......................................... 16
Advanced Zone Setup ................................................... 16
Save Contractor Defaults .............................................. 16
Set Units.............................................................................. 16
Fine-Tune Watering .................................................... 17
System Review ............................................................ 17
Controller Settings .......................................................... 17
Zone Settings.................................................................... 17
Weather Data .................................................................... 18
Weather Log ...................................................................... 18
Event Log............................................................................ 18
System Restore............................................................ 19
Contractor Defaults......................................................... 19
Factory Defaults ............................................................... 19
Manual Watering.........................................................20
Water Individual Zone.................................................... 20
Water All Zones ................................................................ 20
Water Selected Zones .................................................... 20
Advanced ET Programming
Weather Based Irrigation Overview........................21
Factors That Aect Irrigation.................................... 21
Weather............................................................................... 21
Soil Type.............................................................................. 21
Irrigation Scheduling ................................................. 21
Evapotranspiration (ET)................................................. 22
Plant Available Water (PAW)......................................... 22
Management Allowed Depletion (MAD) ................ 22
Congure Controller .................................................. 22
Step 1. Enter Site Location........................................... 22
Step 2. Set Allowed Watering Days .......................... 23
Step 3. Block One Day a Week.................................... 23
Step 4. Set Allowed Watering Windows.................. 24
Step 5. Review.................................................................. 24
Input Zone Information............................................. 25
Zone Setup Wizard.......................................................... 25
Copy Zone to Zone ..................................................... 30
Options
Reset Button ................................................................ 30
Remote Accessories.................................................... 30
Troubleshooting
Watering or Electrical Issues.....................................31
Alarms and Notes .......................................................33
ESP-SMTe Controller User Manual English

ESP-SMTe Controller
3
Installation
Mount Controller
A
Drive a mounting screw into the wall, leaving an 1/8
inch gap between the screw head and the wall surface
(use the supplied wall anchors if necessary), as shown.
B
Locate the keyhole slot on back of the controller unit
and hang it securely on the mounting screw.
1/8 IN.
AB
C
Open the front panel, and drive three additional
screws through the open holes inside the controller
and into the wall, as shown.
1234
VT =VALVE TEST
VT MV COM
24 VAC
GND
SENS
VT MV COM567 11 12 13 17 18 19
1234 8910141516202122
CONNECT
120 VAC
C
Wiring Connections
Connect Valves
A
Route all eld wires through the opening at the
bottom or back of the unit. Attach conduit if desired,
as shown.
WARNING: Do not route the valve wires through the
same opening as the power wiring.
B
Connect one wire from each valve to the terminal on
the base module or Station Module that corresponds
to the desired station number (1-22).
C
Connect a eld common wire (C) to the common
terminal (C) on the base module. Then connect the
remaining wire from each valve to the eld common
wire, as shown.
D
To perform aValveTest, connect the common wire to the
“COM”terminal and the power wire to the “VT” terminal.
This will immediately turn the valve “ON”.
Connect Master Valve (optional)
E
Connect a wire from the master valve (M) to the
master valve terminal (MV) on the base module. Then
connect the remaining wire from the master valve to
the eld common wire, as shown.
A
E
MASTER
VALVE
C
MV
1
2
C
BE C

ESP-SMTe Controller
4
Connect Pump Start Relay (optional)
The ESP-SMTe can control a pump start relay, to turn the
pump on and o as needed.
A
Connect a wire from the pump start relay (PSR) to the
master valve terminal (M) on the base module. Then
connect another wire from the pump start relay to the
eld common wire, as shown.
B
To avoid the possibility of damage to the pump,
connect a short jumper wire from any unused
terminal(s) to the nearest terminal in use, as shown.
NOTE: The ESP-SMTe controller DOES NOT provide
power for a pump. The relay must be wired according
to manufacturer instructions.
Only the following Rain Bird pump start relay models are
compatible with the ESP-SMTe:
Description Note Model No.
Universal Pump Relay 110 volt only PSR110IC
Universal Pump Relay 220 volt only PSR220IC
Dual Pole Pump Relay 110/120 volt PSR110220
NOTE: Connec-
tion to pump
and external
power not
shown. Refer to
pump instal-
lation instruc-
tions.
A
PUMP START
RELAY
B
C
PSR
1
2
Connect Power
WARNING: DO NOT plug in the transformer or con-
nect external power until you have completed and
checked all wiring connections.
WARNING: Electric shock can cause severe injury or
death. Make sure power supply is turned OFF before
connecting power wires.
Indoor Model
A
Route the transformer power cord through the
conduit opening at the bottom left of the unit. Knot
the cable/cord inside the controller cabinet to prevent
it from being pulled out.
WARNING: Do not route the power cord through the
eld wire opening at the bottom right of the unit.
B
Connect the two power wires on the cord to the two
24VAC terminal connections on the controller.
C
Connect the ground wire on the cord to the GND
terminal.
D
Plug the transformer into an electrical outlet.
1234
VT =VALVE TEST
VT MV COM
24 VAC
GND
SENS
VT MV COM567 11 12 13 17 18 19
1234 8910141516202122
TO EXTERNAL
POWER SUPPLY
D
A
B

ESP-SMTe Controller
5
Outdoor Model
Power Wiring Connections
Black supply wire (hot) to the black transformer wire
White supply wire (neutral) to the white transformer wire
Green supply wire (ground) to the green transformer wire
A
Locate the transformer wiring compartment in
the lower left corner of the controller unit. Use a
screwdriver to remove the cover and expose the
transformer connection wires.
B
Route the three external power source wires through
the conduit opening at the bottom of the unit and
into the wiring compartment.
C
Using the provided wire nuts, connect the external
power source wires (two power and one ground) to
the transformer connection wires inside the wiring
compartment.
WARNING: Ground wire must be connected to
provide electrical surge protection. Permanently
mounted conduit shall be used for connecting main
voltage to the controller.
D
Verify that all wiring connections are secure, then
replace the wiring compartment cover and secure it
with the screw.
1234
VT =VALVE TEST
VT MV COM
24 VAC
GND
SENS
VT MV COM567 11 12 13 17 18 19
1234 8910141516202122
A
C
B
Station Expansion Modules
Optional Station Modules are installed in the empty slots to
the right of the base module to increase the station capac-
ity up to 22 stations.
NOTE: For ideal station sequencing, it is recom-
mended that a 6-Station module always be installed
in Bay 2. For more details see the Station Numbering
section.
VT MV COM
 
3-STATION
(ESPSM3) 6-STATION
(ESPSM6)
Expansion Modules
(sold separately)
Base Module
(included)
Install Modules
A
Verify the securing lever on the module is in the
unlocked position (slide to the left).
B
Place the module under the desired slot between the
plastic rails.
C
Push the module up into the slot until secure.
D
Slide the securing lever to the locked position (slide
to the right).
 REPEAT for additional modules.
NOTE: Modules can be installed or removed with OR
without AC power connected. They are considered
“hot-swappable”.
BC
D

ESP-SMTe Controller
6
Station Numbering
Fixed Station Numbering Description
The controller is congured with Fixed Station Numbering.
Each bay is set up to accept a 6 station module and reserve
the station number for future use if a 6 station module is
NOT installed in Bays 2, 3 or 4.
Station numbers are pre-assigned as follows:
VT MV COM 

VT MV COM567 11 12 13 17 18 19
1234 8910141516202122
Bay 1 Bay 2 Bay 3 Bay 4
Example Of Recommended Installation For 19 Stations
Module Conguration
Example of installation with station numbering gaps:
• A total of 19 stations are installed.
• The Base Module is installed in Bay 1 and uses Stations
1 through 4.
• A 6-Station Expansion Module is installed in Bays 2 and
3 using Stations 5 through 16.
• A 3-Station module is installed in Bay 4 and uses sta-
tions numbered 17 through 19.
Because a 3-Station module is installed in Bay 4, only the
rst three station numbers assigned to that bay will be used
and the unused numbers will be “reserved” for future use.
During programming, the controller will skip any unused
station numbers, creating a gap in station numbering.
For the previous example, the rst screen of the Zone Setup
Wizard is displayed. The “No Module” message indicates
there is no module associated with Zone 14.
NOTE: Station numbering gaps will not prevent the
controller from operating properly. It only aects
station numbering. During programming when
connected to AC power, the controller will skip any
unused stations where a module is not installed.
Connect Weather Sensor Wire to
Controller
A
Begin by running 18-2 AWG, UV rated wire from sensor
to controller (200 ft. max.)
NOTE: 25 feet of 18-2 AWG, UV rated wire is provided.
B
Strip wire insulation approx 3/8” and insert leads into
connector located on back of front panel (polarity not
important).
B
C
C
Route the two wires through the provided channel
and out through one of the knockouts, located in the
bottom of the controller cabinet.
Complete Controller Installation
A
Reinstall and reconnect the front panel.
B
Apply power to the controller and test the system.
NOTE: The electrical connections can be checked
even if water is not available. If water is available and
you would like to test some or all of your stations, use
the Test All Stations feature of the controller.Weather
Sensor Installation

ESP-SMTe Controller
7
Weather Sensor Installation
Choose Location
• Select a convenient outdoor location in close proxim-
ity (wire-run distance is 200 feet maximum) to the ESP-
SMTe controller. Place in an unobstructed area away
from reective heat so that the unit can provide accu-
rate on-site temperature and rainfall measurements.
• Mount the unit at least 6 feet above the ground sur-
face to accurately measure ambient temperature. Sug-
gested installation locations include the eave of a resi-
dence roof, a wooden fence post, etc.
• The sensor mounting bracket is designed to mount
on any vertical surface. Easy adjustment of the mount-
ing arm ensures the installed sensor is level. UV rated
#16AWG or #18AWG wire is recommended for the com-
munication wires if more than 25 feet is required.
Sensor Mounting Options
Do’s
• Mount the weather sensor at least six feet
above grade.
• Ensure that sensor is free from obstructions
to allow for collection and accurate mea-
surement of rainfall.
• Sensor does not require direct sun to work
correctly provided any shade or other
obstruction does not block rainfall.
Don’t’s
• Do NOT install sensor in a location where
spray from a sprinkler will collect in the sen-
sor.
• Do NOT install the sensor where rainfall will
be reduced or blocked from entering the
sensor funnel
• Do NOT install the sensor where it will be
impractical to service – the rain sensor may
require cleaning depending on the amount
of leaves, dust, etc that may collect in the
debris screen, funnel, or tipping bucket rain
sensor.
MOUNTED ON
ROOF EAVE
MOUNTED
ON FENCE
MOUNTED
ON POST
CONTROLLER
SENSOR WIRE
(MAX 200 FT.)

ESP-SMTe Controller
8
Mount Weather Sensor
Begin by running the communication wire to the location
where the sensor will be mounted.
A
Place the mounting bracket base assembly against
a mounting surface that permits the top of the
mounting bracket to be adjusted to vertical. Drive a
screw into the upper left hole of the base (do not
tighten completely).
B
Drive a second screw into the middle area of the
adjustment slot, located on the lower right corner of
the mounting base.
C
Level the mounting base and hold it in place, then
tighten the screw in the adjustment slot.
D
Tighten the upper left screw, then drive the two
remaining screws into the mounting base, securing it
to the mounting surface.
A
B
D
D
C
Connect Weather Sensor Wire
A
Loosenthecaptured-screwofthewiring compartment
cover to expose the sensor housing and green wiring
connector within.
B
Strip the two wire leads 1/4” and insert into the
connectors (polarity is not important).
C
If AC power is available, the green LED will blink. Once
communication is established between the sensor
and controller, the LED will light solid.
D
Re-attach the wiring compartment cover and route
the wire through the two openings. Then re-tighten
the captured screw to secure the cover.
D
BC
A
E
Feed the communication wire(s) through the three
holes in the mounting arm, providing“strain-relief”for
the wires. Leave enough extra wire at the top end so
the sensor pod can easily be installed and removed.
F
Mount the sensor housing assembly to the top of
the mounting arm. Align the mounting hole on the
bracket with the arm and tighten using the provided
thumb-screw
G
Adjust each of the mounting arms to assure that the
top of the sensor is secured and level.
H
Press the sensor debris cover onto the top of the
sensor.
G
H
F
E

ESP-SMTe Controller
9
Normal Operation
Controls and Indicators Key operational features of the ESP-SMTe Controller:
Initial Controller & Zone
Set-Up Dial Positions
Alarm Light: Illuminates
when conditions prevent
watering
Large Back Lit Dot-
Matrix Display
Programming Buttons:
Press and Hold to accelerate
settings
English/Spanish Button:
For easy switching of display
language
Remotely Program-
mable: Using 9V battery
(installed inside front panel)
Programming Dial
ESP-SMTe Controller Front Panel
AUTO RUN: Watering
occurs automatically
AUTO MODE
Monday 02 May 2016
05:00 PM
Next
Irrigation
Estimate
05 May
OFF: Cancels all irrigation
Manual Watering: Start
watering selected zones
immediately
System Restore: Restore
contractor and factory
default settings
System Review: Review
controller settings and
logs
Fine-Tune Watering:
Adjust run times by zone
Special Features: Block
irrigation on days of spe-
cial events
Removable Debris Screen:
Easily remove and clean when
clogged
Solar Shield With Temperature
Sensor: Measures temperature
and sends to controller
Mounting Base: Install on eave,
roof, side of house or post
Adjustable Mounting Bracket
Sensor
Housing
Removable Tipping
Rain Bucket: Measures
rainfall amounts and
sends to controller
Weather Sensor Features
NOTE: When installing the weather sensor,
keep away from radiating heat, etc.

ESP-SMTe Controller
10
Operating Modes
When the ESP-SMTe Controller is powered on for the rst
time, the option to select a programming mode is dis-
played.
This screen is also available under the Advanced Control-
ler Setup dial position (see page 15) or after a Factory
Default reset.
AUTO RUN
AUTO RUN is the normal operating mode for the controller.
Irrigation starts automatically when required, and the next
estimated watering date is displayed.
Turn the dial to AUTO RUN.
In AUTO Mode:
• The display shows the current day of the week, date,
time, and the next estimated watering day.
NOTE: On a scheduled watering day, “Next Irrigation
Estimate will change to“Adjusted: 0%”and display any
automatic adjustments to irrigation.
During Watering:
• The display shows the current day, current active zone,
and the Time Remaining for that Zone.
OFF
Cancel all active watering immediately and stop
automatic irrigation.
Turn the dial to OFF.
• Press –or +to adjust the LCD contrast if desired.
Controller Conguration and Zone Information settings
remain stored in memory while the controller is OFF or if
there is a loss of power. Date and time are also maintained
for up to 10 years by an internal battery. A 9V battery is not
required to maintain settings or date and time.
NOTE: Automatic irrigation will NOT occur if the con-
troller remains in OFF mode.

ESP-SMTe Controller
11
Simple Smart Programming
This section provides instructions to setup and operate the
ESP-SMTe.
To program in Simple Smart mode, select Simple Smart on
the Select Programming Mode screen. This screen is avail-
able under the Advanced Controller Setup dial position
(see page 15) or after a Factory Default reset.
Set Date and Time
Set the current calendar Date and Time of day.
Turn the dial to Set Date & Time.
A
Set the current month, day and year.
B
Set the current time.
Congure Controller
Enter site location info and basic irrigation schedules.
In Simple Smart mode, congure the controller by entering
the site zip code for your site, selecting the days to water,
and entering the start times that watering will begin.
NOTE: For Advanced ET mode, see page 21.
Turn the dial to Congure Controller.
Set Site Info
Enter the zip code for your site and the Rain Shuto
parameters for rain sensor shuto.
A
Select Set Site Info.
B
Select Set Zip Code.
C
Enter the zip code for your site.

ESP-SMTe Controller
12
D
Select Set Rain Shuto.
E
Enter the number of Days to delay watering when a
set amount of rain is detected; then press NEXT.
F
Set the amount of rain that will start the delay; then
press NEXT.
G
Press BACK to return to the Congure Controller
menu.
Set Schedule
For each Program (A and B), select the Days to Water and
the Start Times that irrigation will begin.
A
Select Set Schedule.
B
Press UP or DOWN until PROGRAM is blinking; then
press PGM SELECT to choose Aor B.
C
Select Set Days to Water.
D
Select a watering day option.
NOTE: After selecting a watering day option, the
screen will automatically advance to Step 5, Block
One Day a Week.
Water Every Day:
No restrictions on days to water.
Days of the Week:
Set a custom weekly schedule.
• Press OFF or ALLOW to water on the selected day; then
press NEXT.
Even Days:
Water only on even calendar days.
Odd Days:
Water only on odd calendar days (except 31st).

ESP-SMTe Controller
13
Cyclical
Water on a cycle of every 2 to 14 days.
A
Press –or + to set the irrigation cycle and the date to
begin the cycle; then press NEXT.
B
Select a desired day of the week (or none) to Block
Watering.
C
Select Set Start Times.
D
Set the rst Start Time; then press NEXT START to enter
additional times (up to 6 total), or, press DONE to nish.
 REPEAT Steps 2 - 7 for Program B if necessary.
Review Settings
A
Select Review Settings.
.
B
Review the Site Info settings, then press MORE.
C
Review the Watering Day options and programmed
Start Times for Program A, then press MORE.
D
Review Watering Day options and programmed Start
Times for Program B, then press MORE.

ESP-SMTe Controller
14
Input Zone Information
Enter run times for every zone and set up a watering
schedule for new plants.
NOTE: For Advanced ET mode, see page 21.
Turn the dial to Input Zone Information.
• The current programming mode is displayed. Press
MORE to continue.
Set Zone Run Times
Enter desired Run Times for each zone and program.
NOTE: Run Times should be entered based on the
hottest time of year for your location. The SMTe will
make adjustments to the Run Times in Simple Smart
mode based on local weather conditions.
A
Select the desired zone.
B
Select Program A or Program B.
C
Set the Run Time; then press NEXT.
Set Grow-In Schedule
New plants have dierent watering needs than plants that
are already established. New plants are watered every day
during a set Grow-In Schedule period, then are watered
according to regular schedules when the period ends.
A
Press +when OFF is blinking to enable the Grow-In
Schedule for the selected zone; press NEXT to return to
the Set Run Times screen.
B
Set the number of days the Grow-In period will last.
C
Set the number of Cycles per day (up to 8).
D
Set the Cycle time (duration of each Cycle).
E
Set the Start Time (time the rst Cycle begins).
F
Set the Start interval time (minutes between Cycles).

ESP-SMTe Controller
15
Special Features
Select additional features and controller setup options.
Turn the dial to Special Features.
Event Days O
Event Days O allows you to select up to four dates to
block irrigation for special occasions up to a year in
advance.
A
Select Event Days O.
B
Press +to add a new date.
C
Set the date; then press NEXT to set additional dates.
D
To delete an Event Day O, select the date using NEXT
or BACK and press and HOLD -.
Short Circuit Test
Verify the integrity of the wires between the controller and
the valves.
A
Select Short Circuit Test.
The test result for each zone is displayed; the test takes
about 30 seconds to complete.
B
Press RETEST to run the test again if desired.
NOTE: “NoMod” indicates that no module is present
for that station number.
Advanced Controller Setup
Set time delays between zones and set thresholds that
determine when the controller will suspend irrigation due
to weather conditions.
A
Select Adv. Controller Setup.
B
Set each value; then press NEXT.
• Zone to Zone Delay sets a time delay between one sta-
tion valve turning o and the next station valve turning
on.
• Suspend Watering When Rain Reaches value sus-
pends irrigation when measured rainfall reaches the
specied amount.
• Suspend Watering When Temp Below value suspends
irrigation when the temperature falls below a specic
value.

ESP-SMTe Controller
16
Select Programming Mode
After setting the Temp Below value on the Advanced Con-
troller Setup screen (and pressing NEXT), the option to
switch programming modes is displayed.
• Select the desired programming mode.
Advanced Zone Setup
Set each zone to use (or not to use) an installed master
valve, pump start relay, or the ESP-SMTe Rain Gauge.
A
Select Advanced Zone Setup.
B
Select the desired zone.
C
Select YES for Auto-Adjust to choose whether a zone’s
durations are adjusted due to weather.
D
Select YES if MV is energized when the selected zone
starts.
E
Select YES if the zone’s irrigation should be suspended
due to rain or not (e.g. plants under a covered patio).
Save Contractor Defaults
Save the current Congure Controller and Input Zone
Information settings for all zones to memory.
A
Select Save Contractor Dts.
B
Press SAVE to save zone and controller settings to
Contractor Defaults.
C
Read the Warning; then press SAVE.
D
Current Settings are saved; press CONTINUE.
Set Units
Set the Time format (AM/PM or 24-Hour) and Units format
(English or Metric) that is displayed by the controller.
A
Select Set Units.
B
Select the desired Time Format.
C
Select the desired Units Format.

ESP-SMTe Controller
17
Fine-Tune Watering
Adjust the calculated run time for each zone.
Turn the dial to Fine-Tune Watering.
A
Press BACK or NEXT to select the zone to adjust.
B
Press –or + to set the adjustment percentage for the
selected zone.
C
After making any adjustments, return the dial to
AUTO RUN.
If minor adjustments are required to calculated run times,
you can increase or decrease run times for ET zones by a
selected percentage. These adjustments will apply until
you set the value back to 0.
The Fine Tune % By Zone value can be adjusted from -60%
to +60%. For example, if a +50% adjustment is set, then a
calculated run time of 10 minutes will become 15 minutes.
NOTE: Fine-Tune Watering adjustments always apply
to all zones in Simple Mode.
NOTE: Fine Tune settings can be adjusted for Newly
Planted zones, but will not take eect until the Newly
Planted mode expires.
System Review
View system settings and weather information.
NOTE: The information under System Review is for
review purposes only. This allows the review of pro-
gramming settings without accidentally making
unwanted changes.
Turn the dial to System Review.
Controller Settings
Review Congure Controller settings.
A
Select Controller Settings.
B
Review location data and delay settings; then press
MORE.
C
Review Program A; then press MORE.
D
Review Program B then press MORE.
Zone Settings
Review Input Zone Information and Advanced Zone Setup
settings.
A
Select Zone Settings.

ESP-SMTe Controller
18
B
Review zone settings; then press MORE.
C
Review Grow-In Schedule; then press BACK.
Weather Data
Review the current temperature and rainfall over the past
24 hours based on data from the SMTe Weather Sensor.
A
Select Weather Data.
B
Review Weather Data; then press BACK.
Weather Log
Review a daily log of high and low temperatures,
calculated ET values, and rainfall over the past month.
A
Select Weather Log.
B
Review Weather Log; then press BACK.
Event Log
Review notications and error messages concerning
irrigation events by date or by zone. Check these messages
if the controller is not operating as expected.
A
Select Event Log.
B
Events and alarms can be viewed by date or by zone.
NOTE: A table in the Contractor’s Manual on the web-
site (www.rainbird.com/esp-smte) lists all the mes-
sages that can appear in the Event Logs.

ESP-SMTe Controller
19
System Restore
Restore Contractor Default settings and restore original
Factory Default settings.
Turn the dial to System Restore.
Contractor Defaults
Restore settings that were saved using the Save Contractor
Defaults feature.
NOTE: Current settings are overwritten.
A
Select Contractor Defaults.
B
Press RESTORE to restore the Contractor Defaults.
C
The following screen is displayed while the controller
recongures.
• When the restore is complete, the display returns to the
RESTORE SETTINGS menu.
Factory Defaults
Restore the original factory default settings.
NOTE: All current zone settings are erased. Any settings
saved using Save Contractor Defaults are NOT affected.
A
Select Factory Defaults.
B
Press RESTORE to restore the Factory Defaults.
C
The following warning is displayed; press RESTORE.
D
The following screen is displayed while the controller
recongures.
E
When the restore is complete, the option to switch
programming modes is displayed.
F
Select the desired programming mode and begin
programming the controller per the mode selected.
>> For Simple Smart mode, go to page 11.
>> For Advanced ET mode, go to page 21.

ESP-SMTe Controller
20
Manual Watering
Start watering immediately for selected zones or for all
zones.
NOTE: If Manual Watering is started during automatic
irrigation, the watering schedule is canceled for the
day and resumes on the next Allowed Watering Day.
Turn the dial to Manual Watering.
Water Individual Zone
A
Select Water Individual Zone from the Manual
Watering screen.
NOTE: A selected zone will be activated even if it is
not ENABLED. A zone that does not have an associ-
ated station module will display No Module.
B
Select the desired zone; then press NEXT.
C
Set the run time for the selected zone; then press
NEXT.
Water All Zones
A
Select Water All Zones from the Manual Watering screen.
NOTE: All zones will be activated even if they are not
ENABLED. Zones will not activate that do not have an
associated station module installed.
B
Set the run time for all zones; then press START.
Water Selected Zones
A
Select Water Selected Zones from the Manual
Watering screen..
NOTE: Selected zones will be activated even if they
are not ENABLED. Zones that do not have an associ-
ated station module will display n/a.
B
Select the desired zone or zones.
C
Set the run time for every desired zone; then press
NEXT until you reach the end of your available zones.
D
NEXT will change to START; then press START.
During All Manual Watering:
The Watering - Manual screen shows the current zone and
time remaining.
A
Press –or + to adjust the time remaining if desired.
B
Press ADV. ZONE to advance to the next zone if
desired.
C
To cancel watering, press CANCEL or turn the dial to
OFF for three seconds and then return the dial to the
AUTO RUN position.