Ramteq BVE Series User manual

READ THIS MANUAL
This manual contains important information for the use and safe operation of
your RAMTEQ®machine. FAILURE TO READ THIS MANUAL AND
FOLLOW ITS INSTRUCTIONS PRIOR TO OPERATING OR ATTEMPTING
ANY SERVICE OR MAINTENANCE PROCEDURE COULD RESULT IN
SERIOUS INJURY OR DEATH TO YOU OR OTHER PERSONS; ALSO
DAMAGE TO THE MACHINE OR TO OTHER PROPERTY.
Operator’sManual
BVE SERIES
Electric Motor / Diesel fired
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 2
Section 1 operator’SManual
Unpacking....................................................................2
Safety inStrUctionS and WarningS.............................3
operating inStrUctionS...............................................4
Maintenance inStrUctionS...........................................5
Section 2 partS and Service Manual
partS diagraM.............................................................7
HoSe, Wand, & gUn.....................................................8
pUMpS...........................................................................8
BUrner aSSeMBly..........................................................9
control Box aSSeMBly.................................................9
plUMBing diagraMS....................................................10
Wiring diagraMS........................................................12
troUBleSHooting........................................................13
 W arranty ..............................................................14
Table of Contents
NOTICE
Information in this operator’s manual is subject to change without notice.
RAMTEQ SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN. This operator’s manual
contains information protected by copyright. No part of this operator’s manual may be photocopied or reproduced in any form without
prior written consent from RAMTEQ
®
.
© RAMTEQ
®
, 2005
All rights reserved. Printed in USA.
INCLUDED PARTS
• Pallet
• Packing Material
Outer Box
• BVE Series Machine
• Operator’s Manual
• Wand / Trigger Gun
• Nozzles 0º15º25º40º
• Hose 3/8” X 50’
• QC Hose Fittings
INSPECTION
Carefully unpack your new RAMTEQ equipment by removing the banding
and cardboard box from pallet. Remove the pressure washer from the
pallet and check for any physical damages that may have occurred during
shipment. Check for all parts specified and shown below.
Unpacking Instructions

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 3
DO NOT operate this machine in areas where open flames are not permitted. DO NOT store or
use combustible materials on or near this machine. Use this equipment only in well ventilated
areas. Failure to follow this warning may cause carbon monoxide build up, fire or explosion, and
possible injury or death.
DO NOT operate this machine while under the influence of alcohol, drugs or while fatigued.
DO NOT direct discharge stream at yourself or others. Risk of injection or injury may occur.
Never put your hand or fingers over the spray tip. Do not try to stop or deflect leaks with your
hand or body. Always face nozzle and wand to the ground when testing.
DO NOT operate this machine WITHOUT wearing protective Eye Wear. Gloves, Hard Hat, Mask,
Ear Plugs & Steel Toe Work Boots are also recommended, DO NOT wear loose clothing. Keep
your body and clothing clear of the engine and discharge stream when the machine is running.
DO NOT tie back or block trigger gun in OPEN position. Never leave the pressure washer
unattended once you have started it. If you leave, shut down machine completely.
DO NOT overreach or stand on an unstable support while operating this machine. Maintain
good footing and balance.
DO NOT permit this machine to run while unattended or for extended periods of time with
trigger gun closed. Damage to pump may occur.
DO NOT operate this machine in an unsafe manner or around unsupervised children. Keep all
other personnel clear while operating this machine. This product should only be operated by
trained personnel.
DO NOT alter original factory settings prior to operating this machine. Risk of injury to yourself or
other persons may occur.
DO NOT remove hoses, guns, nozzles or any components while this machine is still hot or while
it is running.
DO NOT attempt to service this machine before reading the service manual.
DO NOT use water with a temperature over 140 degrees Fahrenheit
DO NOT use any electrical outlet that is not properly grounded or does not comply with all
federal, state, and local laws and/or electrical codes
DO NOT put diesel fuel in to a gasoline tank or gasoline into a diesel tank. Observe correct
markings on fuel tanks before filling.
DO NOT operate this machine without knowing how to stop and bleed water pressures. Know all
controls before using this machine.
DO NOT spray caustic, acids or abrasive fluids through this machine.
DO NOT permit water to freeze inside this machine. Pump and plumbing damage may occur.
Use only recommended RAMTEQ parts when servicing this machine.
RAMTEQ will not be held liable for any unauthorized modifications made to this
machine. Any such action will void the warranty.
Safety Guidelines
reaD tHIs FIrst! FAILURE TO READ AND OBSERVE ALL
WARNING STATEMENTS COULD RESULT IN SEVERE BODILY
INJURY OR DEATH, POSSIBLE INJURY TO OTHER PERSONS,
DAMAGE TO MACHINE OR OTHER PROPERTY.
�
WARNING

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 4
LOCATION GUIDELINES
Locate the machine on a solid and level surface so that engine and pump crankcase oil lubricate components properly.
Avoid areas where water can build up in the working area. Possible injury can occur caused by the surface becoming
slippery from water build up.
Locate the machine in a well-ventilated area and away from flammable materials or fumes. Be sure ventilation warnings
are observed. Keep pressure washer at least 18” away from flamable materials.
Locate the machine so the operator has easy access to the pressure washer and its controls. Locate the machine so that
it is protected from external damage.
To prevent damage and excessive hose wear, locate the pressure washer so that the hose does not cross traffic areas
STARTING THE MACHINE
Following the steps below will insure successful operation:
Read this manual completely before attempting to start the machine.
Check that the Motor/Burner switches are in the "OFF" position
Check the diesel tank and fill with a good grade of diesel fuel #1, #2 or kerosene.
Check the pump oil level and fill with SAE 30w non-detergent oil if needed.
Connect water hose to pump (or float tank if equipped). Turn on water source.
Connect the power cord to a properly grounded power source.
Attach high pressure hose to base of spray gun.
Install water nozzle at the end of wand, making sure it is clear of any obstructions.
Turn pump switch to “ON”
Pull trigger on gun until a steady stream of water comes out the nozzle. This purges any air in the system.
Check for leaks in the system and cycle trigger gun to insure bypass is adjusted correctly. Repair any leaks and correct
unloader adjustment if needed. Turn off machine before attempting any repairs.
Turn burner switch to "ON". Check gor buner ignition.
Adjust thermostat to desired temperature appropriate to the task. Maximum temperature setting may not be needed.
Insert detergent siphoning tube into a DOT approved container and open the metering valve for detergent application.
WASHING TECHNIQUES
Washing from bottom up increases dwell time of soap and lessens vertical streaks.
Turn soap metering valve “OFF” to purge system of soap
Rinsing with cold water from top down will retard detergent reaction which will enhance
the rinsing performance.
Wash at 30 to 60 degree angles to prevent splashback.
STOPPING THE MACHINE
Turn burner switch to “OFF”. Allow water to discharge for a few minutes while cooling down.
Turn pump switch to "OFF".
Disconnect water source.
Pull gun trigger to release water pressure from system.
Disconnect wand & gun assembly.
Wind up pressure hose on hose reel.
Operating Instructions

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 5
MAINTENANCE PRECAUTIONS
 Do not permit acidic, caustic or abrasive fluids to be pumped through system.
Periodically clean detergent inlet screen. This will ensure proper flow of water to the pump.
High mineral content in water may adversely affect your machine and may require the use of a water softener
to ensure proper operation.
NEVER run the pump dry under any circumtances. Doing so will cause exteme damage to the pump.
HEAT EXCHANGER COIL MAINTENANCE
  Hard water conditions may eventually cause clogging in the heat exchanger coil if left unattended.
Scale deposits will compromise the heating efficiency and produce an unsafe condition over time.
It may be necessary to descale coil.
 Scale buildup from certain detergents may eventually clog up the heat exchanger coil causing an
unsafe condition. Use only recommended detergents for better cleaning efficiency.
 Black carbon deposits that collect on the outside wall of the heat exchanger coil may be a result of
using a poor grade of fuel or improper burner operation. Heating fuel should be void of water and
sediments to eliminate the possibility of sooting and compromising the efficiency of the coil.
FAILURE TO MAINTAIN HEAT EXCHANGER COIL MAY
RESULT IN A STEAM EXPLOSION WHICH MAY CAUSE
SERIOUS INJURY OR DEATH.
�
WARNING
Maintenance Instructions
MOVING, STORAGE
 Place machine in covered area when not in use to protect from elements.Protect machine from
freezing in cold temperatures by storing in a heated location.
WINTERIZING
 Non-float Tank Machines: To protect the machine from freezing temperatures while
storing or transporting, connect short length of garden hose (approximately 3 ft.) to
water inlet connection on machine. Remove the pressure nozzle from the wand and
insert the short garden hose end into a container of antifreeze. Place the wand into the
antifreeze container and start engine running machine until antifreeze appears from the
end of the wand. Turn engine “OFF” and replace pressure nozzle. Coil up hose and
move machine to storage area.
 Float Tank Machines: Pour antifreeze into float tank and remove water nozzle from end
of wand and carefully insert into opening of float tank. Start machine and run until
antifreeze water mixture has circulated throughout the machine returning back to the
float tank.
PUMP MAINTENANCE
 Fill crankcase to dot on oil gauge window per specifications with the specific oil created by the pump
manufacturer (i.e. General Pump Oil). Ensure the right oil for specific pump as it may vary.
 Change oil after 40 Hour Break-in Period.
 Change oil every Three Months or at 500 Hour Intervals thereafter.

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 6
ELECTRODE SETTINGS
Inspection of all wires, spring
contacts and electrodes should
be done periodically.
OIL BURNER AIR BAND ADJUSTMENT
RAMTEQ
®
sets oil burners at sea level. Air bands may need adjustment at higher elevations to offer
enhanced performance of the burner and extended life of the machine.
Adjustment of burner is done with pump motor and thermostat
set to maximum. Loosen locking screw on air band, then close
band until black smoke vents up exhaust vent. Take careful note
of air band position when black smoke is first noticed. Slowly
open air band until white smoke vents, then turn air band halfway
back to where black smoke was first noted. Tighten air band
locking screw. When properly set, the unit should NOT have either
"black" smoke or "white" smoke during operation.
IF BLACK OR WHITE SMOKE VENTS FROM EXHAUST
PORT UPON STARTING EQUIPMENT, DISCONTINUE USE
AND ADJUST AIR BANDS BEFORE RESTARTING.
�
WARNING
Maintenance Instructions
 All RAMTEQ machines have the unloader
correctly set at the the factory. Setting an
unloader is a difficult job without the proper
equipment and training. Should the need arise
to change the unloader settings, please contact
your local distributor.
UNLOADER ADJUSTMENT
CHANGING THE UNLOADER SETTINGS WITHOUT THE PROPER
EQUIPMENT AND TRAINING MAY RESULT IN NON-WARRANTY
DAMAGE TO THE PUMP.
�
WARNING
Sutner
Unloader

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 7
Ref.# Part # Description Qty.
1 190-00002-01 Fuel Tank, 9 gallon green 1
2 140-00001-01 Cap, Fuel Gauge, Diesel, Black 1
3a 200-00009-01 Motor, 5hp 208/230/1 Baldor L1410T 1
3b 200-00005-01 Motor, 5hp 208/230/3 Baldor M3218T 1
3c 200-00012-01 Motor, 6hp 208/230/1 Baldor 1
3d 200-00010-01 Motor, 7.5hp 208/230/1 Baldor L1510T 1
3e 200-00006-01 Motor, 7.5hp 208/230/3 Baldor M3311T 1
3f 200-00007-01 Motor, 10hp 230/460/3 Baldor M3313T 1
4 180-00008-01 Chassis, BV Series 1
170-00002-01 Wheel, Caster Swivel, 6” 2
170-00004-01 Wheel, Caster Swivel, 8” 2
180-00052-01 Bracket, four wheel configuration 2
5 170-00003-01 Wheel, pneumatic split rim 2
6 516-00001-01 Bushing, wheel collar, 5/8” 2/4
7 175-00001-02 Axle, two and four wheel configuration 1/2
567-00016-01 Washer, Wheel Plastic 2/4
8a 250-00004-01 Burner, Assembly 208/230/1 1
8b 250-00001-01 Burner, Assembly 460/3 1
9 180-00007-01 Plate, Burner 1
10 055-00029-01 Float Tank Assembly 1
11 180-00009-01 Handle 1
180-00038-01 Wand, Box 1
567-00015-01 Grommet, Rubber Wand Holder, 2” 1
12 180-00020-01 Shell, SS Removable, 18” X 23”H 1
191-00006-01 Insulation, Blanket 1” x 24”w, 4# 1
13 180-00072-01 Cap, Coil Large 1
14 191-00004-01 Insulation, Cap, 18” x 10” 1
15 155-00003-01 Coil, Large, Diesel Fired 1
16 180-00021-01 Shell, SS Stationary, 18” X 23”H 1
17 180-00063-01 Belt Guard, Enclosure 1
18 180-00062-01 Belt Guard 1
19a 220-00004-01 Pump, General T1011-R (BVE 500,600) 1
19b 220-00009-01 Pump, General TS2021-R (BVE 750,1000) 1
180-00051-01 Bracket, Pump Belt Tension Stationary 1
20 180-00006-01 Plate, Power 1
567-00001-01 Grommet, Nozzle Holder 4
584-00003-11 Pulley, 2BK50H (BVE 500,600) 1
584-00002-09 Pulley, 2BK80H (BVE 500,600) 1
586-00004-04 Belt, BX36 (BVE 500,600) 2
516-00002-03 Bushing, SP, Split Taper, H 1-1/8” (BVE 500,600) 1
516-00002-01 Bushing, SP, Split Taper, H-24mm (BVE 500,600,750,1000) 1
584-00002-08 Pulley, 2BK45H (BVE 750) 1
584-00002-09 Pulley, 2BK80H (BVE 750) 1
586-00004-04 Belt, BX36 (BVE 750) 2
516-00002-04 Bushing, SP Split Taper, H 1-3/8” (BVE 500,750,1000) 1
584-00002-04 Pulley, 2BK57H (BVE 1000) 1
584-00002-06 Pulley, 2BK70H (BVE 1000) 1
586-00004-04 Belt, BX36 (BVE 1000) 2
9
10
11
12
13
14
16
17
18
1
2
3
4
5
67
8
20
19
15
BVE Parts Diagram Exploded
view on
page 9.

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 8
Ref.# Part # Description Qty.
1a 270-00028-01 Nozzle, Water #5.5 0º (BVE 500,600) 1
1b 270-00028-02 Nozzle, Water #5.5 15º(BVE 500,600) 1
1c 270-00028-03 Nozzle, Water #5.5 25º(BVE 500,600) 1
1d 270-00028-04 Nozzle, Water #5.5 40º(BVE 500,600) 1
1e 270-00025-01 Nozzle, Water #4.0 0º (BVE 750) 1
1f 270-00025-02 Nozzle, Water #4.0 15º(BVE 750) 1
1g 270-00025-03 Nozzle, Water #4.0 25º(BVE 750) 1
1h 270-00025-04 Nozzle, Water #4.0 40º(BVE 750) 1
1i 270-00028-01 Nozzle, Water #5.5 0º (BVE 1000) 1
1j 270-00028-02 Nozzle, Water #5.5 15º(BVE 1000) 1
1k 270-00028-03 Nozzle, Water #5.5 25º(BVE 1000) 1
1m 270-00028-04 Nozzle, Water #5.5 40º(BVE 1000) 1
2 265-00001-01 36” Wand, Insulated 1
3 275-00001-01 ST1500 Trigger Gun 1
4 552-00004-03 3/8” Quick Connect, Female Plug 1
5 284-00001-01 Hose 3/8” X 50” R-1 Swivel Ends 1
BVE Belt Drive Pump
Hose, Wand & Gun
General Pump T1011-R, T2011-R, TS2021-R Triplex Plunger Pump
1
3
4
5
2
Ref.# Part # Description Qty.
1 220-00004-01 T1011 Triplex Plunger Pump Complete (BVE 500,600) 1
1a 220-00009-01 TS2021 Triplex Plunger Pump Complete (BVE 1000) 1
2 221-00001-06 Manifold, Brass Head T1011 (BVE 500,600) 1
2a 221-00001-02 Manifold, nickle plated Head TS2021 (BVE 750, 1000) 1
Pump Repair Kits
Part # Description Qty.
221-00002-01 Check Valve Assembly Kit #1 (All BVE Series) 6
221-00018-01 Oil Seal Kit #2 (All BVE Series) 3
221-00019-01 Oil Ring and Valve Cap Kit # 4 (T1011) 6
221-00026-01 Oil Ring and Valve Cap Kit #5 (T2011) 6
221-00010-01 Head Packing Complete Kit #28 (All BVE Series) 1

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 9
Ref.# Part # Description Qty.
1 180-00027-01 Control Box Panel 1
2 180-00150-01 Control Box 1
3 305-00006-01 Label,Control Box Small 1
4 571-00002-01 Hour Meter 1
5 450-00001-01 Pump/Burner Switch On/Off 2
6 573-00001-01 Thermostat Assembly 1
7 505-00001-01 1/4 -20 Bolt 2
8 508-00002-02 Tinnerman 2
6
7
8
1
1a
2
345
BVE Burner Assembly
BVE Control Box Assemblies
9
8
1
2
4
3
7
6
Ref.# Part # Description Qty
1 251-00001-01 Fuel Pump w/ Solenoid 115v 1
2 256-00001-02 Main Burner Gasket 1
3 245-00012-16 Nozzle 1
4 258-00002-02 Electrode Pair 1 pr
5 252-00001-03 Transformer 115v 1
5a 252-00001-02 Transformer 208/230v 1
6 253-00001-02 Coupling 1
7 253-00002-02 Fan Wheel 6.25”x4.0” 1
8 254-00001-03 Motor 115v/60/1 1
8a 254-00001-02 Motor 208/230v/60/1 1
9 577-00003-01 Filter, Fuel Inline Racor 1
578-00001-01 Element, Fuel Filter, Racor 1
280-00003-01 Hose, Inlet/Outlet Fuel Line (not shown) 2
556-00001-01 Clamp, Hose (not shown) 2
Burner Assembly Complete
250-00007-01 EH-V-115 (BVE 500, 750, 1000)
250-00004-01 EH-V-230 (BVE 500, 600, 750, 1000)
5

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 10
(SOCKET HEAD)
ELBOW, BRASS
#8 FLARE X 1/4 NPTM
ELBOW, PLATED STEEL
3/8 NPTM X 3/8 NPTM
#4 JIC FEMALE X 1/4 BARB
HOSE END, SWIVEL
#4 FLARE X 3/8 NPTM
ELBOW, BRASS
3/8 BARB X 3/8 NPTM
CONNECTOR, BRASS
LOW PRESSURE HOSE
3/8 I.D. X 13"
#8 JIC FEMALE X 3/8 BARB
HOSE END, SWIVEL
3/8 NPT STREET
TEE, BRASS
3/8 NPTF X 1/2 NPTF
ELBOW, PLATED STEEL
(SOCKET HEAD)
BUSHING, BRASS
1/2 NPTM X 3/8 NPTF
SWIVEL, HOSE END
#8 JIC SWIVEL X 1/2 BARB
3/8 NPT BRANCH
TEE, BRASS
ELBOW, BRASS
#8 FLARE X 3/8 NPTM
PUMP 1/2 NPT PLUG
NIPPLE, GALVANIZED STEEL
TO COIL INLET
1/2 NPT X 2.5"
ELBOW, PLATED STEEL
3/8 NPT, STREET (2 PL.)
3/8 I.D. X 14"
COUPLER, FRAME MOUNTED
ELBOW, BRASS
1/2 NPT X 1/2 BARB
LOW PRESSURE HOSE
SECTION AA
FLOW SWITCH
1/4 NPT PLUG (2 PL.)
ELBOW, BRASS
3/8 NPTM X 3/8 BARB
ELBOW, BRASS (2 PL.)
1/4 NPTM X 1/4 BARB
3/4 SWIVEL X 3/8 NPTM
GARDEN HOSE CONNECTOR
3/8 NPTF X 3/8 NPTF
GIANT #22532A
POP-OFF VALVE
(PRESET 2600 PSI)
3/8 NPTM SWIVEL X 3/8 HOSE (2 PL.)
3/8 NPT STREET
TEE, PLATED STEEL
1/4 I.D. X 37", BLACK
LOW PRESSURE HOSE
ELBOW, POLYPROPYLENE
3/8 BARB X 3/8 BARB
HOSE END, HIGH PRESSURE
3/8 NPTF X 3/8 NPTF
COUPLER, PLATED STEEL
1/4 NPT PLUG
1/4" I.D. TUBE X 50"
1/4 NPT PLUG
SUTTNER ST-261
UNLOADER
DETERGENT LINE
METER VALVE
3/8 BARB X 3/8 BARB X 3/8 BARB
TEE, POLYPROPYLENE
CLAMP BAND
Ø0.4 - 0.9
3/8 NPT PLUG
CLAMP (2 PL.)
FLOAT VALVE (2 PL.)
RAMTEQ
Ø1/4 -5/8 (7 PL.)
CLAMP BAND
BULKHEAD FITTING
1/2 NPTF I.D.
1/2 I.D. X 50"
LOW PRESSURE HOSE
(REAR VIEW)
FLOAT TANK
BV500-17
HIGH PRESSURE HOSE
TEE, PLATED STEEL
3/8 NPT STREET
3/8 I.D. X 18"
BV500-18
BV500-16
BV500-12
BV500-11
BV500-10
BV500-05
BV500-06
BV500-04MODELS:
THERMOSTAT
MANIFOLD
FROM COIL OUTLET
1/2 NPT X 2.5"
NIPPLE, GALVANIZED STEEL
JE ADAMS 7420 (2500 PSI)
RELIEF VALVE
3/8 NPTM X 3/8 MALE
QUICK CONNECT COUPLER
BUSHING, PLATED STEEL
3/8 NPT X 1/4 NPT
LOW PRESSURE HOSE
1/2 NPT X 1/2 BARB
3/8 I.D. X 14"
3/8 NPTF X 3/8 NPTF
COUPLER, FRAME MOUNTED
ELBOW, BRASS (2 PL.)
#4 JIC FEMALE X 1/4 BARB
HOSE END, SWIVEL
TEE, BRASS
3/8 NPT STREET
3/8 BARB X 3/8 NPTM
CONNECTOR, BRASS
#4 FLARE X 3/8 NPTM
ELBOW, BRASS
LOW PRESSURE HOSE
3/8 I.D. X 13"
#8 FLARE X 1/4 NPTM
PRESSURE SWITCH
CONNECTOR, BRASS
#8 JIC FEMALE X 3/8 BARB
HOSE END, SWIVEL
SECTION AA
ELBOW, BRASS
3/8 NPTM X 3/8 BARB
1/4 NPTM X 1/4 BARB
GARDEN HOSE CONNECTOR
3/4 SWIVEL X 3/8 NPTM
ELBOW, PLATED STEEL (SOCKET HEAD)
1/2 NPT PLUG
(SOCKET HEAD)
1/2 NPTM X 3/8 NPTF
BUSHING, BRASS
3/8 NPT BRANCH
#8 JIC SWIVEL X 1/2 BARB
SWIVEL, HOSE END
#8 FLARE X 3/8 NPTM
TEE, BRASS
3/8 NPTM X 3/8 NPTM
ELBOW, BRASS
A
PUMP
TO COIL INLET
NIPPLE, GALVANIZED STEEL
3/8 NPTF X 1/2 NPTF
ELBOW, PLATED STEEL
1/2 NPT X 2.5"
QUICK CONNECT COUPLER
3/8 NPTM X 3/8 MALE
RELIEF VALVE
JE ADAMS 7420 (2500 PSI)
NIPPLE, GALVANIZED STEEL
THERMOSTAT
MANIFOLD
3/8 NPT PLUG
ELBOW, BRASS
3/8 BARB X 3/8 BARB
ELBOW, POLYPROPYLENE
LOW PRESSURE HOSE
1/4 I.D. X 37", BLACK
1/4" I.D. TUBE X 50"
3/8 NPT PLUG
1/4 NPT PLUG
SUTTNER ST-280
UNLOADER
A
METER VALVE
TEE, POLYPROPYLENE
3/8 BARB X 3/8 BARB X 3/8 BARB
Ø0.4 - 0.9
CLAMP BAND
DETERGENT LINE
3/8 NPTM SWIVEL X 3/8 HOSE (2 PL.)
3/8 NPT, STREET
ELBOW, PLATED STEEL
TEE, PLATED STEEL
3/8 NPT STREET
HOSE END, HIGH PRESSURE
HIGH PRESSURE HOSE
3/8 I.D. X 18"
CLAMP (2 PL.)
FLOAT VALVE (2 PL.)
CLAMP BAND
Ø1/4 -5/8 (7 PL.)
1/2 NPTF I.D.
BULKHEAD FITTING
RAMTEQ
FLOAT TANK
(REAR VIEW)
1/2 I.D. X 50"
LOW PRESSURE HOSE
BV500-14
FROM COIL OUTLET
BV500-15
1/2 NPT X 2.5"
MODELS: BV500-01
BV500-03
BV500-02
BV500-08
BV500-09
BV500-07
BV500-13
BVE 500, 600 Base Plumbing
BVE 500, 600 Upgrade Plumbing

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 11
FLOAT TANK
(REAR VIEW)
CLAMP (2 PL.)
HOSE END, HIGH PRESSURE
COUPLER, PLATED STEEL
3/8 NPTM SWIVEL X 3/8 HOSE (2 PL.)
ELBOW , PLATED STEEL
RAMTEQ
ELBOW, BRASS
3/8 I.D. X 13"
3/8 BARB X 3/8 NPTM
CONNECTOR, BRASS
ELBOW, BRASS
#4 FLARE X 3/8 NPTM
#8 JIC FEMALE X 3/8 BARB
HOSE END, SWIVEL
LOW PRESSURE HOSE
#8 FLARE X 3/8 NPTM
SWIVEL, HOSE END
#8 JIC SWIVEL X 1/2 BARB
3/8 NPT BRANCH
HOSE END, SWIVEL
#4 JIC FEMALE X 1/4 BARB
TEE, BRASS
3/8 NPT STREET
TEE, BRASS
#8 FLARE X 1/4 NPTM
3/8 NPTM X 3/8 NPTM
ELBOW, PLATED STEEL
ELBOW, BRASS
A
1/2 NPTM X 3/8 NPTF
BUSHING, BRASS
PUMP
557-00001-01
3/4 SWIVEL X 3/8 NPTM
3/8 NPTM X 3/8 BARB
530-00003-04
ELBOW, BRASS
GARDEN HOSE CONNECTOR
FLOW SWITCH
1/4 NPT PLUG (2 PL.)
METER VALVE
579-00006-01
528-00006-01
UNLOADER
3/8 NPT, STREET (2 PL.)
ELBOW, PLATED STEEL
SUTTNER, ST-261S
SECTION AA
530-00002-02
ELBOW, BRASS (2 PL.)
1/4 NPTM X 1/4 BARB
3/8 NPTF X 3/8 NPTF
3/8 NPT STREET
1/4 NPT PLUG
A
DETERGENT LINE
1/4" I.D. TUBE X 50"
285-00002-01
1/4 NPT PLUG
518-00002-01
557-00001-01
1/2 NPTF I.D.
Ø1/4 -5/8 (7 PL.)
CLAMP BAND
TEE, POLYPROPYLENE
3/8 BARB X 3/8 BARB X 3/8 BARB
BULKHEAD FITTING
531-00002-01
1/2 NPT X 1/2 BARB
280-00002-02
3/8 I.D. X 14"
LOW PRESSURE HOSE
557-00001-02
CLAMP BAND
Ø0.4 - 0.9
3/8 NPTF X 3/8 NPTF
COUPLER, FRAME MOUNTED
ELBOW, BRASS
ELBOW, POLYPROPYLENE
539-00002-01
280-00002-01
1/4 I.D. X 37", BLACK
LOW PRESSURE HOSE
531-00002-01
3/8 BARB X 3/8 BARB
FLOAT VALVE (2 PL.)
569-00002-01
(SOCKET HEAD)
ELBOW, PLATED STEEL
3/8 NPTF X 1/2 NPTF
1/2 NPT X 2.5"
NIPPLE, GALVANIZED STEEL
1/2 NPT PLUG
(SOCKET HEAD)
TO COIL INLET
(PRESET 3600 PSI)
GIANT #22533A
POP-OFF VALVE
3/8 NPT PLUG
TEE, PLATED STEEL
3/8 NPT STREET
3/8 I.D. X 24"
HIGH PRESSURE HOSE
THERMOSTAT
3/8 NPTM X 3/8 MALE
528-00006-01
ELBOW, PLATED STEEL
3/8 NPT, STREET
5833 PSI
RUPTURE DISK
QUICK CONNECT COUPLER
NIPPLE, GALVANIZED STEEL
1/2 I.D. X 51"
LOW PRESSURE HOSE
MANIFOLD
1/2 NPT X 2.5"
BV1000s
FROM COIL OUTLET
BV750-05
BV750-06
BV750-10
BV750-12
BV750-11
BV750-17
BV750-18
BV750-16
MODELS: BV750-04
BV750-01
BV750-03
BV750-02
BV750-07
BV750-08
BV750-09
BV750-13
MODELS:
BV750-15
FROM COIL OUTLET
BV750-14
1/2 NPT X 2.5"
MANIFOLD
THERMOSTAT
FLOAT TANK
(REAR VIEW)
LOW PRESSURE HOSE
1/2 I.D. X 50"
3/8 I.D. X 18"
HIGH PRESSURE HOSE
CLAMP (2 PL.)
HOSE END, HIGH PRESSURE
QUICK CONNECT COUPLER
3/8 NPTM X 3/8 MALE
RELIEF VALVE
NIPPLE, GALVANIZED STEEL
JE ADAMS 7468 (3500 PSI)
[phone]
Ø0.4 - 0.9
CLAMP BAND
1/2 NPTF I.D.
BULKHEAD FITTING
TEE, POLYPROPYLENE
3/8 BARB X 3/8 BARB X 3/8 BARB
CLAMP BAND
Ø1/4 -5/8 (7 PL.)
A
SUTTNER ST-280
UNLOADER
METER VALVE
1/4" I.D. TUBE X 50"
DETERGENT LINE
3/8 NPTF X 3/8 NPTF
GARDEN HOSE CONNECTOR
3/4 SWIVEL X 3/8 NPTM
SECTION AA
3/8 NPTM X 3/8 BARB
ELBOW, BRASS
1/4 NPTM X 1/4 BARB
ELBOW, BRASS (2 PL.)
CONNECTOR, BRASS
#8 FLARE X 1/4 NPTM
HOSE END, SWIVEL
#8 JIC FEMALE X 3/8 BARB
LOW PRESSURE HOSE
1/2 NPT X 1/2 BARB
ELBOW, BRASS
COUPLER, FRAME MOUNTED
3/8 I.D. X 14"
RAMTEQ
3/8 BARB X 3/8 BARB
ELBOW, POLYPROPYLENE
FLOAT VALVE (2 PL.)
LOW PRESSURE HOSE
1/4 I.D. X 37", BLACK
TO COIL INLET
(SOCKET HEAD)
1/2 NPT PLUG
(SOCKET HEAD)
3/8 NPT PLUG
NIPPLE, GALVANIZED STEEL
1/2 NPT X 2.5"
ELBOW, PLATED STEEL
3/8 NPTF X 1/2 NPTF
3/8 NPT, STREET
TEE, PLATED STEEL
3/8 NPT STREET
PUMP
ELBOW, PLATED STEEL
3/8 NPT PLUG
1/4 NPT PLUG
#8 FLARE X 3/8 NPTM
ELBOW, BRASS
A
TEE, BRASS
3/8 NPT BRANCH
#8 JIC SWIVEL X 1/2 BARB
SWIVEL, HOSE END
TEE, BRASS
3/8 NPT STREET
3/8 I.D. X 13"
PRESSURE SWITCH
LOW PRESSURE HOSE
HOSE END, SWIVEL
CONNECTOR, BRASS
3/8 BARB X 3/8 NPTM
ELBOW, BRASS
#4 FLARE X 3/8 NPTM
#4 JIC FEMALE X 1/4 BARB
3/8 NPTM X 3/8 NPTM
ELBOW, PLATED STEEL
BUSHING, PLATED STEEL
3/8 NPT X 1/4 NPT
1/2 NPTM X 3/8 NPTF
BUSHING, BRASS
3/8 NPTM SWIVEL X 3/8 HOSE (2 PL.)
BVE 750, 1000 Base Plumbing
BVE 750, 1000 Upgrade Plumbing

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 12
BLK
A1
A2
WHT
BLK
L2
A1
A2
WHT
RED
WHT
96
95
M1
RED
Orange
Red
Blue
Blue
Red
PUMP SW
Wht
Wht
Blk
Blk
Wht
MODULE
BURNER
Transformer
Orange
Fuel
for Ignitor
Red
Solenoid
Wht
Burner
Mtr
Blk
BLK
F3
WHT
BLUE
Motor
Pump
WHT
WHT
T2
T1 T3
BLK
ORANGE
F1
F2
T1
BLUE
WHT
BLK
WHT
BLK
ORANGE
RED
WHT
WHT
96
95
M1
RED
OL
OL OL
M1
L1 L3
BLK
RED
H4 H2 H3 H1
X1 X2
L1
L2
ELEC BOX
LOCATED
BELOW DECK
GRN
115V
GRN
SW
1
P1
GRN
208-230V 208-230V
BURNER
FLOW
SW
ELEC BOX
LOCATED
BELOW DECK
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 NW FREEWAY PHONE: [phone]
HOUSTON, TX 77040 FAX: [phone]
wiring BVE 230v 1Ph Base
bve
b.peplinski
10/13/04 A
A10/13/04 release bbp
1 of 1
1Ph UNITS
BVE, XVE
BASE
ELECTRICAL SCHEMATIC
230 VOLT
Wiring Effective:
10/13/2004
BVE Wiring Diagrams

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 13
BVE Wiring Diagrams
A1
PART OF CABLE "A"
WHT
BLK
L2
A2
PUMP SW
Red
Red
Blue
Blue
Orange
Blk
Wht
MODULE
BURNER
WHT
Wht
HOURMETER
deR
egnarO
Blk
Solenoid
Fuel
Burner
Motor
Wht
Transformer
for Ignitor
Blk
Wht
BLK
Wht
F3
WHT
BLUE
Motor
Pump
WHT
T2
T1 T3
BLK
ORANGE
F1
F2
T1
WHT
BLK
RED
WHT
WHT
96
95
M1
RED
OL
OL OL
M1
L1 L3
BLK
RED
H4 H2 H3 H1
X1 X2
L1
L2
GRN
GRN
208-230V
SW
BURNER
115V
3
2
UNLOADER SW
GRN
SW
FLOW
TIMER
1
208-230V
P1
4
5
1
CONTROL BOX
ELEC BOX
LOCATED
BELOW DECK
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 N W F RE E WAY PH O N E: 713 . 983.60 0 0
HOUST O N , TX 7704 0 F AX : 7 13.98 3 . 6405
wiring BVE, XVE 230v 1Ph Upgrade
bve
b.peplinski
10/13/04 C
A10/13/04 release bbp
1 of 1
B4/19/05 changes/clean up bbp
C9/27/05 more clean up, add XVE bbp
1Ph UNITS
BVE, XVE
UPGRADE
ELECTRICAL SCHEMATIC
230 VOLT
Wiring Effective:
9/27/2005

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 14
P
3
4
3
Q
A1
A2
WHT
Blue
WHT
Motor
Pump
RED
Red
Red
Burner
Wht
Blk
Blue
Orange
Blk
Wht
PUMP SW
Orange
Wht
Blk
Red
Wht
for Ignitor
Transformer
Mtr
Fuel
Solenoid
BLK
WHT
ORANGE
BLUE
WHT
BLK
F3
BLUE
BLK
WHT
WHT
F2
T1
F1
T2
OL
OL
T1
96
OL
T3
M1
WHT
L1 95
WHT
BLK
M1
L3 RED
BLK
WHT
ORANGE
BLK
RED
H4 H2 H3 H1
X1 X2
L2 L1
208-230V
ELEC BOX
LOCATED
BELOW DECK
BLK
WHT
RED
BURNER
SW
115V
208-230V
P1
1
SW
FLOW
BURNER
MODULE
CONTROL BOX
ELEC BOX
LOCATED
BELOW DECK
WHT
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 NW FREEWAY PHONE: [phone]
HOUSTON, TX 77040 FAX: [phone]
wiring BVE 230v 3Ph Base
bve
b.peplinski
10/13/04 A
A10/13/04 release bbp
1 of 1
3Ph UNITS
BVE, XVE
BASE
ELECTRICAL SCHEMATIC
230 VOLT
Wiring Effective:
10/13/2004
L2
BVE Wiring Diagrams

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 15
BVE Wiring Diagrams
L2
A2
A1
Pump
Motor
RED
WHT
M1
T1
BLUE
ORANGE
F3
T2
WHT
WHT
BLK
L3
L1
M1
T3
OL
Motor
Contactor
w/ thermal
T1
OL
overload
protection
OL
WHT
BLUE
ORANGE
BLK
WHT
F2
BLK
RED
F1
BLK
WHT
WHT
95
96
RED
Blue
Red
Wht
Blk
Orange
Blk
BLK
Orange
Red
Wht
Blk
for Ignitor
Transformer
Wht
Mtr
Burner
Fuel
Solenoid
PUMP SW HOURMETER
Red
Blue
Wht
BURNER
MODULE
Wht
H4 H2 H3 H1
X1 X2
L2 L1
ELEC BOX
LOCATED
BELOW DECK
BLK RED
WHT
115V
208-230V
1
P1
208-230V
123
54
TIMER
UNLOADER SW
FLOW
SW
BURNER
SW
GRN
GRN
GRN
CONTROL BOX
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 NW FREEWAY PHONE: [phone]
HOUSTON, TX 77040 FAX: [phone]
wiring BVE 230v 3Ph Upgrade
bve
b.peplinski
10/13/04 A
A10/13/04 release bbp
1 of 1
3Ph UNITS
BVE, XVE
UPGRADE
ELECTRICAL SCHEMATIC
230 VOLT
Wiring Effective:
10/13/2004

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 16
BURNER
MODULE
PART OF CABLE "A"
L2
A1
A2
GRN
GRN
GRN
GRN
Pump
Motor
RED
Red
Wht
Blk
Wht
Blk
SW1
Wht
Wht
CONTROL PANEL
MODULE
BURNER
Blk
1
P
Wht
Blk
Fuel
Solenoid
for Ignitor
Transformer
Wht
Mtr
Burner
PUMP SW
T2
WHT
WHT
WHT
WHT
T1
F1
F3
BLK
F2
BLK
protection
overload
w/ thermal
Contactor
Motor
M1
RED
OL
OL OL
T3
M1
WHT
BLK
L1 L3
96
95
RED
WHT
T1
WHT
BLK
BLK
RED
RED
H4 H2 H3 H1
X1 X2
RED
L2
L1
RED
WHT
ELEC BOX
LOCATED
BELOW DECK
BLK
115V
THERMOSTAT
ORG
SW
FLOW
SW
BURNER
ELEC BOX
LOCATED
BELOW DECK
WHT
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 NW FREEWAY PHONE: [phone]
HOUSTON, TX 77040 FAX: [phone]
wiring BVE 460v 3Ph Base
bve
b.peplinski
10/13/04 A
A10/13/04 release bbp
1 of 1
3Ph UNITS
BVE, XVE
BASE
ELECTRICAL SCHEMATIC
460 VOLT
Wiring Effective:
10/13/2004
BVE Wiring Diagrams

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 17
BVE Wiring Diagrams
K
BURNER
MODULE
ORG
L2
A1
A2
AUX
13
14
BLUE
BLUE
BLUE
GRN
GRN
GRN
GRN
Pump
Motor
RED
Blk
Wht
SW1
Wht
Fuel
Solenoid
1
P
Blk
for Ignitor
Transformer
Wht
Mtr
Burner
Wht
Blk
HOURMETER
Wht
BURNER
MODULE
CONTROL PANEL
Red
PUMP SW
T2
WHT
WHT
WHT
WHT
T1
F1
F3
BLK
F2
BLK
protection
overload
w/ thermal
Contactor
Motor
M1
RED
OL
OL OL
T3
M1
WHT
BLK
L1 L3
96
95
WHT
T1
WHT
BLK
BLK
RED
RED
H4 H2 H3 H1
X1 X2
RED
L2
L1
ELEC BOX
LOCATED
BELOW DECK
BLK RED
WHT
115V 4
1
5
TIMER
23
UNLOADER SW
FLOW
SW
THERMOSTAT
SW
BURNER
ELEC BOX
LOCATED
BELOW DECK
WHT
RED
BLK
PROJECT:
SCALE: DO NOT SCALE
DRAWN BY:
DATE:
DRAWING NUMBER:
REV:
SHEET NO:
NAME
REVISIONS
DATE:
NO.
ECN:
14275 NW FREEWAY PHONE: [phone]
HOUSTON, TX 77040 FAX: [phone]
wiring BVE 460v 3Ph Upgrade
bve
b.peplinski
10/13/04 B
A10/13/04 release bbp
1 of 1
3Ph UNITS
BVE, XVE
UPGRADE
ELECTRICAL SCHEMATIC
460 VOLT
Wiring Effective:
2/22/2006
B2/22/06 change wiring bbp

OperatOr’sManual
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00002-01 11/05
page 18
Low Water Pressure Insufficient water source Check hose size/water source
Old or incorrect nozzle Replace nozzle
Plumbing or hose leak Tighten, repair or replace leak
Obstruction in spray nozzle Clean or replace nozzle
Chemical valve open Close valve or submerge hose
Unloader valve worn Replace unloader
Pump valves dirty or worn Clean or replace packing/valves
No Chemical Flow Detergent valve closed Open detergent valve
Low detergent level Fill detergent container
Chemical screen dirty Clean detergent screen
Burner Not Igniting No fuel Fill fuel tank with proper fuel
Burner switch turned off Turn burner switch on
Thermostat set too low Reset thermostat
Clogged fuel filter Replace fuel filter
Defective pressure switch Replace pressure switch
Clogged burner nozzle Replace burner nozzle
Fuel pump malfunction Replace fuel pump
Improper electrode setting Clean/reset to specifications
Excessive Burner Smoke Improper fuel being used Use Diesel #1/#2 or Kerosene
Water contamination in fuel Drain fuel and replace with new
Improper air band adjustment Readjust air band/altitude
Low fuel pressure Adjust to specifications
Air leaks in fuel lines Check for air leaks or bubbles
Soot on coils/burner assembly Clean coils/burner assembly
Misaligned electrodes Realign to specifications
Dirty burner nozzle Clean or replace burner nozzle
Pressure Relief Valve Leaks Nozzle is dirty Clean or replace nozzle
Defective relief valve Replace relief valve
Unloader adjusted incorrectly Adjust unloader valve
Restriction on discharge hose Remove nozzle and flush line
Scale restricting flow in coil Clean coil
Pump Motor Not Running Pump motor switch off Turn on pump motor switch
GFCI tripped Reset and test GFCI
No voltage to machine Check power source
Clogged water nozzle Clean water nozzle
Insufficient voltage/amperage Use proper drop cord
Pump Noisy Air in suction line Check inlet water fittings
Pump valves dirty Clean/replace pump valves
Check valve springs worn Replace check valves
Low pump oil Add SEA 30wt. non-detergent
Pump bearings are worn Replace/rebuild pump
Incoming water too hot Reduce temperature/ambient
Water In Oil High humidity environment Change oil frequently
Oil seal worn Check and replace oil seal
Plunger packing worn Check and replace packing
Water Dripping/Pump Plunger packing is worn Install new packing kit
Plunger retainer oil ring worn Replace oil ring
Cracked ceramics Replace ceramics
Oil Dripping Oil seal worn Check and replace oil seals
Cracked manifold Replace manifold
Fluctuating Pressure Unloader not adjusted Adjust to specifications
Valves worn Replace with valve kit
Dirt or blockage in valves Clean or replace valve
Pump sucking air Check water/detergent supply
Worn plunger packing Replace packing kit
Pump Head Overheating Extended period in bypass Pull trigger gun for water flow
problem cause action
Troubleshooting

RAMTEQ
RAMTEQ®14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone] 300-00001-01 1/13
WARRANTY
Limited One Year
Ramteq Incorporated ("RAMTEQ") warrants that the Product you have purchased from RAMTEQ or from an
Authorized RAMTEQ Reseller is free from defects in materials or workmanship under normal use for a period of one
(1) year from the date of purchase. This warranty extends only to you, the original Purchaser. It is not transfer-
able to anyone who subsequently purchases the Products from you. This warranty specifically excludes expendable
items, including but not limited to hoses, seals, nozzles and gunjets. RAMTEQ manufacturers warrant certain com-
ponents of the Products for periods greater than one (1) year. MOTORS, GENERATORS, PUMPS, COILS, BURNERS
AND ENGINES ARE WARRANTED BY THEIR RESPECTIVE MANUFACTURERS, AND SERVICED THROUGH THESE
MANUFACTURERS' LOCAL AUTHORIZED SERVICE CENTERS. Specific warranty details can be found on the indi-
vidual manufacturers website. RAMTEQ CANNOT PROVIDE WARRANTY ON THESE ITEMS.
During the warranty period, RAMTEQ will repair or replace defective parts, at the option of RAMTEQ.
This limited warranty does not extend to any Product not purchased from RAMTEQ or from an Authorized RAMTEQ
Reseller. This limited warranty also does not extend to any Product that has been damaged or rendered defective (a)
as a result of accident, misuse or abuse; (b) by operation outside the specifications in the intended applications; (c) by
the use of parts not sold or manufactured by RAMTEQ; (d) by the modification of the Product.
Warranty Disclaimer
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, RAMTEQ MAKES NO OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. RAMTEQ EXPRESSLY DISCLAIMS ALL AND ANY WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY HAVE BEEN IMPOSED BY LAW ARE LIMITED TO THE TERMS
OF THIS EXPRESS LIMITED WARRANTY.
Limitation of Remedy
RAMTEQ IS NOT LIABLE FOR ANY DAMAGES CAUSED BY THE PRODUCT OR FAILURE OF THE PRODUCT TO
PERFORM, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. THIS LIMITATION APPLIES WHETHER
DAMAGES ARE SOUGHT, OR A CLAIM MADE, AS A CONTRACT CLAIM, AS A TORT CLAIM, OR ANY OTHER
CLAIM.
THIS LIMITATION OF LIABILITY, HOWEVER, WILL NOT APPLY FOR PERSONAL INJURY.
U.S.A. State Laws
Some states do not allow limitation on how long an implied warranty lasts. In such states, the limitations or
exclusions of this Limited Warranty may not apply to you.
Some states do not allow the exclusion or limitation in incidental or consequential damages for consumer products. In
such states, the exclusion may not apply to you. This limited warranty gives you specific legal rights. You may also
have other rights that may vary from state to state. You are advised to consult applicable state laws for a full
determination of your rights.
How to Obtain Warranty Service
TO OBTAIN WARRANTY SERVICE YOU MUST CONTACT RAMTEQ or an AUTHORIZED RAMTEQ RESELLER.

Ramteq
Ramteq Pressure Washers 14275 NORTHWEST FREEWAY HOUSTON, TX 77040 PHONE: [phone] FAX: [phone]
Click on pictures to open manufacturers website.
Manufacturers Warranty Period
5 years
5 years
3 years
3 years
3 years
18 months
18/36 months 1 year
3 years