rangeiot OrangeIOT RZ User manual

OrangeIOT RZ
Installation Guide
PLEASE KEEP THIS GUIDE
This guide contains important information about your lock.
www.i-orangeiot.com
Customer Service: [email protected]
PLEASE KEEP THIS GUIDE
This guide contains important information about your lock.
OrangeIOT RZ
Installation Guide
www.i-orangeiot.com
Customer Service: sup[email protected]

backset
60 or 70 mm
35 mm to 50 mm
A
A B C
D
B C D
1"
25 mm
1Prepare the door and check dimensions
Measure to confirm that the hole in the door
is 2-1/8" (54 mm)
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm)
Measure to confirm that the the hole in
the door edge is 1" (25 mm)
Measure to confirm that the door is 1-3/8"
to 2" (35 mm or 50 mm)thick
2Install the latch and strike
Latch Exterior Assembly
Battery Cover
Strike
A
E
K
B
F
G
BCD
Parts List
Drive-In Collar
Latch and
Strike Screws
Mounting Plate
Interior Assembly
Screws
Interior
Assembly
Mounting Plate
Screws
L
Backup Key
A
Is the door edge chiseled?
Is the backset 2-3/8”(60mm)?
Hold the latch in front of the door hole, with
the latch face flush against the door edge
YES
YES
NO
NO
Install latch in door with
supplied screws.
No adjustment is
required. Proceed
to next step.
Yes, it is 2-3/8” (60mm). No, it is 2-3/4” (70mm)
Rotate and pull the
latch as shown
to extend latch.
Use a screwdirver to test if deadbolt works smoothy.
chiseled not
chiseled
Make sure hole in door frame is drilled a
minimum of 1” (25 mm) deep.
H
I
I
HC
or
or
1 / 6
Use a flathead screwdriver to remove
Rectangular face from latch and install
drive-in collar.
Install strike on the door frame
2-3/8" or 2-3/4"
1-3/8" to 2"
54 mm
2-1/8"
φ2-3/4”
(70mm)
φ2-3/8”
(60mm)
1
φ2-3/4”
(70mm)
2
1
2
3
4
Actual Size
J
Install latch in door with wood
block and hammer.
Installation Guide
Latch/Strike
Screws(I)
Latch/Strike
Screws(H)
Mounting Plate
Screws
Strike
Interior Assembly
Screws
Mounting
Plate
Battery
Cover
Interior
Assembly
Exterior
Assembly
Backup Key
Latch

3Install exterior assembly
ASend the cable through the bottom
horizontal slot in the mounting plate.
C
Secure the mounting plate with the supplied screws.
D
IMPORTANT: Before installation, make sure the latch
is fully retracted (in the unlocked position) .
Route the cable below the latch
B
2 / 6
4Install interior assembly
Connect the cable and ensure tight cable connection.
A
Secure the interior assembly
with the supplied screws.
D
Rotate the turnpiece in vertical position and the torque
blade in horizontal position, make sure the latch is
still fully retracted (in the unlocked position).
BTest operation using backup key and thumbpiece
for smooth rotation.If turnpiece doesn’t rotate,
repeat step 4B, making sure the turnpiece in vertical
position, and touque blade in horizontal position.
C
5Detect left/ right hand door installation
While the door is OPEN and UNLOCK, load 3 AA batteries
into the interior assembly. For best results, use new,
non-rechargeable Alkaline batteries only.
Press and hold the Reset button on the interior assembly
using a pen or a paper clip.
Reset the lock to teach the lock the orientation of the door.
ALoad the last battery and keep holding the reset button
for 3 seconds, until you hear the sound of “beep”. The
latch bolt will extend to learn the orientation of the door.
BRe-install battery cover. C
J
K
IMPORTANT:This step is required and crucial for the lock to operate properly.
Actual Size
Actual Size
Keep Parallel to door edge.
Horizontal

Information & Safety Warnings
Protect your User Codes and Master Code.
Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered
without your knowledge.
This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure
a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive
cleaners or polishes could damage the coating and result in tarnishing.
IMPORTANT: Do not load batteries until lock is completely installed.
123456789
A.
123456789
B.
222222222
C.
3865
D. If
Then
and
Forward number sequence
Backward number sequence
Repeat number sequence
38 1965
19 3865
Contain existing code sequence
1. Master Code(4 to 10 digits) : The default Master Code is 12345678. It is recommended that you change it to a code of
your own.
2. User Code(4 to 10 digits) : A total of 20 User Codes (and one temporary one-time User Code) may be programmed.
3. Both master and user pin codes don not support the following combination of numbers.
Item Specifications Remarks
AA alkaline battery x4
(Operation voltage: 4.6~6.0V)
Last up to one year
(10 times open/close per day)
Battery
Parts Illustrations
The default Master Code is 12345678. It is recommend that you change it to a code of your own
3 / 6
Programming Instructions
Keypad
Cylinder
Multi-Function
Button(MFB)
Battery Cover
Reset Button
Thumb Turn
Interior Assembly
Exterior Assembly

Definitions
Master Code
Required for programming and feature settings. Master
code can be used to unlock the door under vacation
mode.
Property owner/ manager should keep this information
confidential.
Auto Lock
Automatically locks the deadbolt 30 seconds after
unlocking. This feature is off by default. You can set
the Auto Lock time delay between 10 and 99 seconds.
Wrong Entry Limit
After 10 unsuccessful attempts at entering a valid PIN
code, the unit will shut down for 3 minuets.
Silent Mode
The beep sounds when pressing keypad can be muted.
But you will still hear low battery and system alerts.
Vacation Mode
This is a security feature for you when you are leaving
your home for vacation or long trip. It can be enabled in
master mode. Enabling vacation mode will restrict all
user pin codes until master pin code is entered on
keypad. If the lock is unlocked by thumb turn, the lock
will sound an alarm.
One Time User Code
This code can only be used once and is automatically
deleted when used.
4 / 6
Unlock with Fake PIN code
User can prevent pin code exposure from strangers by
entering random digits before or after pin code.
83618 137192 14710
password
Random digits
How To Use
Unlock the door
1.Unlock the door from outside
2.Unlock the door from inside
Master/ User
pin code
Rotate the thumb turn to
Unlock position.
Lock the door
1. Lock the door from outside
Auto Lock Mode
In Auto lock mode, the bolt will
extend out automatically in 30
seconds after unlocking
Manual Mode
Press any key on keypad for 2
seconds
2. Lock the door from inside
Auto Lock Mode
In Auto lock mode, the device will
be locked automatically.
Manual Mode
Rotate the thumb turn to Lock
position.

5 / 6
Quick Set Up
The default Master Code is 12345678. It is recommended that you change it to a code of your own
Notes:
When setting is unsuccessful, the indicator light will flash red.
Change
Master
PIN
Code Wait for
Green Light Flash
Succeed
Green Light Flash
Wait for
Green Light Flash
Succeed
Green Light Flash
Succeed
Green Light Flash
Wait for
Green Light Flash
Press
1
Wait for
Green Light Flash
Press
2
Wait for
Green Light Flash
Press
3
Wait for
Green Light Flash
Press
4
2
New Master PIN Code
New User PIN Code
Unwanted User PIN Code
Green Light Flash
Silent Mode Enabled
Green Light Flash
Silent Mode Disabled
New User PIN Code
New Master PIN Code
Add
User
PIN
Code
Delete
User
PIN
Code
Silent
Mode
Wait for
Long Green Lights
Master PIN Code
* *
Wait for
Long Green Lights
Master PIN Code
Wait for
Long Green Lights
Master PIN Code
Wait for
Long Green Lights
Master PIN Code
Add
One-Time
PIN
Code Succeed
Green Light Flash
Green Light Flash
Green Light Flash
Wait for
Green Light Flash
Press
5
2
Wait for
Green Light Flash
Wait for
Green Light Flash
Press
7
Auto Lock Enabled
Auto Lock Disabled
New User PIN Code New User PIN Code
Auto
Lock
Wait for
Long Green Lights
Master PIN Code
Wait for
Long Green Lights
Master PIN Code
Green Light Flash
Vacation Mode Enabled
Wait for
Green Light Flash
Press
6
Vacation
Mode
Wait for
Long Green Lights
Master PIN Code
Set
Auto
Lock
Time
Delay
Enter New Duration
Time (10-99)
Succeed
Green Light Flash
Wait for
Green Light Flash
Press
8
Wait for
Long Green Lights
Master PIN Code

6 / 6
Factory Default Settings
The turnpiece cannot rotate or operate the lock.
Remove and re-install the lock, making sure that the turnpiece is in vertical position.
The lock cannot be locked or unlocked by the keypad.
Make sure that the codes are not disabled. If needed, restore the lock’s default settings.
The keypad doesn’t respond when touched ( no lights are visible and no beeping is heard) .
Make sure the cables are properly connected, and make sure the batteries are new and installed correctly.
After the installation of the batteries, there is no response when you press any button and no beeps are heard.
Check the cable connection and the polarity of the batteries. Also make sure the batteries are not dead.
I forgot my Master Codes.
Perform a reset in order to erase all passcodes. Once the reset is complete, all passcodes will be erased and the Master code
will return to the default value ( 12345678) .
Troubleshooting
Settings Factory Defaut
Master PIN Code
Auto Lock
Silent Mode
Wrong Code Entry Limit
Shutdown Time
Vacation Mode
12345678
Disabled
Disabled
10 times
3 mins
Disabled
1. Keep the door open and unlock.
2. Press and hold the Reset button, at the same time take out one battery and then place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of beep.
Restore To Factory Default Settings
This procedure will delete all User Codes associated with the lock.
* If none of the above resolves your issue, please contact customer service at [email protected]