rangeiot RZ-A Operating instructions

PLEASE KEEP THIS GUIDE
This guide contains important information about your lock.
PLEASE KEEP THIS GUIDE
This guide contains important information about your lock.
Installation & Programming
Guide
RZ-A

backset
60 or 70 mm
35 mm to 50 mm
A
A B C
D
B C D
1"
25 mm
1Prepare the door and check dimensions
Measure to confirm that the hole in the door
is 2-1/8" (54 mm)
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm)
Measure to confirm that the the hole in
the door edge is 1" (25 mm)
Measure to confirm that the door is 1-3/8"
to 2" (35 mm or 50 mm)thick
2 Install the latch and strike
Latch Exterior Assembly
Battery Cover
Strike
A
E
K X 3
B
F
G
BCD
Parts List
Drive-In Collar
(Optional)
Latch and
Strike Screws
Mounting Plate
Interior Assembly
Screws
Interior
Assembly
Mounting Plate
Screws
L X 1
Backup Key
A
Is the door edge chiseled?
Is the slotted hole centered in the door hole?
Hold the latch in front of the door hole, with
the latch face flush against the door edge
YES
YES
NO
NO
Install latch in door with
supplied screws.
No adjustment is
required. Proceed
to next step.
Slotted hole is centered. slotted hole is NOT centered.
Rotate and pull the
latch as shown
to extend latch.
Use a screwdirver to test if deadbolt works smoothy.
chiseled not
chiseled
IMPORTANT:
Make sure hole in door frame is drilled a
minimum of 1" (25 mm) deep.
H X 2
I X 2
I
HC
or
or
1 / 6
Use a flathead screwdriver to remove
Rectangular face from latch and install
drive-in collar.
Install strike on the door frame
Check the alignment to make sure when the
deadbolt is extended, it is going into the bolt
hole and not hitting the deadbolt strike or
door frame.
2-3/8" or 2-3/4"
1-3/8" to 2"
54 mm
2-1/8"
1
φ2-3/4”
(70mm)
2
1
2
3
4
J X 2
Install latch in door with wood
block and hammer.
Installation Guide
Latch
Screws(I)
Strike
Screws(H)
Mounting Plate
Screws
Strike
Interior Assembly
Screws
Mounting
Plate
Battery
Cover
Interior
Assembly
Exterior
Assembly
Backup Key
Latch
Make sure
the UP icon
gose up.
Tool Required: #2 Philips screwdriver
! Use of a powered screwdriver is not recommended.

3Install exterior assembly
AIMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position) . B Route the cable below the latch and
insert the cylinder tailpiece horizontally through the slot in the latch.
2 / 6
4Install interior assembly
Connect the cable and ensure tight cable connection.
BRotate the turnpiece in vertical position and
the tailpiece in horizontal position.
Make sure the latch is still fully retracted
(in the unlocked position).
C
5 Reset the lock to teach the lock the orientation of the door
While the door is OPEN and UNLOCK,
load 3 AA batteries into the interior assembly.
For best results, use new, non-rechargeable Alkaline
batteries only. Do not mix old and new batteries.
APress and hold the Reset button on the interior assembly
using a pen or a paper clip.
Do not release the reset button until you completed the
next step.
BLoad the 4th battery and keep holding the reset button
for 10 seconds, until you hear the sound of “beep”.
After the beeping sound, the latch bolt will extend
automatically.
This indicates that the lock has learn the orientation of
the door and the lock is restored to factory setting.
C
Test operation using backup key and thumbpiece
for smooth rotation.
If turnpiece doesn’t rotate, repeat step 4C, making
sure the turnpiece in vertical position, and touque
blade in horizontal position.
D
IMPORTANT: Always run this step after installation.
The motor will not operate before completing the step.
IMPORTANT: Do not load batteries until lock is completely installed.
Remove the battery cover.
Locate the slot at the bottom and use your fingernail or a
flat head screwdriver to pry the cover up and pull it off.
A
Secure the interior assembly
with the supplied screws.
E
K
Secure the mounting plate with the supplied screws.
D
J
Keep Parallel to door edge.
Horizontal
unlocked
Send the cable through the bottom horizontal slot in the mounting plate.
C
Eunlocked
G
F
Horizontal
horizontal
Unlocked
VERTICAL
UNLOCKED

3 / 6
Information & Safety Warnings
Protect your User Codes and Master Code.
Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered
without your knowledge.
IMPORTANT:
The default master code is 12345678.
Your must change this code to a code of your own before the electronic features of this product will work.
123456789
123456789
B.
222222222
C.
3865
D.
Then
and
38 1965
19 3865
Forward number sequence
Backward number sequence
Repeat number sequence
1. Master Code (4 to 10 digits) : The default Master Code is 12345678. It is required that you change it to a code of your
own before programming.
2. User Code (4 to 10 digits) : A total of 20 User Codes (and one temporary one-time User Code) may be programmed.
3. Both master and user pin codes don not support the following combination of numbers.
Programming Instructions
How To Use
UNLOCK the door LOCK the door
Master/ User
code
Rotate the thumb turn to
Unlock position.
Auto Lock
Enable auto lock so the bolt will
extend out automatically in 30 seconds
after unlocking.
! This feature is off by default.
One-touch Locking
Press and hold any key for 2 seconds.
Rotate the thumb turn to
Lock position.
Programming Basic
A.
Contain existing code sequence If

4 / 6
Item Specifications Remarks
AA alkaline battery x4
(Operation voltage: 4.6~6.0V)
Last up to one year
(10 times open/close per day)
Battery
(Use new, non-rechargeable
Alkaline batteries only.)
Parts Illustrations
The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
Keypad
Cylinder
Multi-Function
Button(MFB)
Battery Cover
Reset Button
Thumb Turn
Interior Assembly
Exterior Assembly
Definitions
Master Code
Required for programming and feature settings.
Property owner/ manager should keep this information
confidential. The default master code is 12345678.
This code needs to be changed before programming.
Auto Lock
Automatically locks the deadbolt 30 seconds after
unlocking. This feature is off by default. You can set
the Auto Lock time delay between 10 and 99 seconds.
Wrong Entry Limit
After 10 unsuccessful attempts at entering a valid PIN
code, the unit will shut down for 3 minuets.
Silent Mode
The beep sounds when pressing keypad can be muted.
But you will still hear low battery and system alerts.
One Time User Code
This code can only be used once and is automatically
deleted when used.
Vacation Mode
Enabling vacation mode will restrict all user codes
until master code is entered on keypad. If the lock is
unlocked by thumb turn, the lock will sound an alarm.
Low Battery Indicator
If you hear 10 beeps corresponding with 10 red flashing
red lights, that's an indication that the batteries need to
be replaced soon.
Please replace with 4 new AA alkaline batteries and do
not mix old and new batteries.
All settings are retained in the memory when the
batteries are removed and replaced.
Unlock with Fake code
User can prevent pin code exposure from strangers by
entering random digits before or after pin code.
83618 137192 14710
password
Random digits

5 / 6
Quick Set Up
IMPORTANT: The default Master Code is 12345678. It is recommended that you change it to a code of your own
Notes:
· Each step of a function programming sequence needs to be completed within 5 seconds.
·When setting is unsuccessful, the indicator light will flash 5 red lights and exit programming mode.
Change
Master
Code
Wait for
Green Light Flash
Succeed
Green Light Flash
Wait for
Green Light Flash
Succeed
Green Light Flash
Succeed
Green Light Flash
Wait for
Green Light Flash
Press
1
Wait for
Green Light Flash
Press
2
Wait for
Green Light Flash
Press
3
Wait for
Green Light Flash
Press
4
2
New Master Code
New User Code
Unwanted User Code
Green Light Flash
Silent Mode Enabled
Green Light Flash
Silent Mode Disabled
New User Code
New Master Code
Add
User
Code
Delete
User
Code
Silent
Mode
Wait for
Long Green Lights
Master Code
* *
Wait for
Long Green Lights
Master Code
Wait for
Long Green Lights
Master Code
Wait for
Long Green Lights
Master Code
Add
One-Time
Code
Succeed
Green Light Flash
Green Light Flash
Green Light Flash
Wait for
Green Light Flash
Press
5
2
Wait for
Green Light Flash
Wait for
Green Light Flash
Press
7
Auto Lock Enabled
Auto Lock Disabled
New User Code New User Code
Auto
Lock
Wait for
Long Green Lights
Master Code
Wait for
Long Green Lights
Master Code
Green Light Flash
Vacation Mode Enabled
Wait for
Green Light Flash
Press
6
Vacation
Mode
Wait for
Long Green Lights
Master Code
Set
Auto
Lock
Time
Delay
Enter New Duration
Time (10-99)
Succeed
Green Light Flash
Wait for
Green Light Flash
Press
8
Wait for
Long Green Lights
Master Code

6 / 6
Factory Default Settings
The turnpiece cannot rotate or operate the lock.
Remove and re-install the lock, making sure that the turnpiece is in vertical position.
The lock cannot be locked or unlocked by the keypad.
Make sure that the codes are not disabled. If needed, restore the lock’s default settings.
The keypad doesn’t respond when touched ( no lights are visible and no beeping is heard) .
Make sure the cables are properly connected, and make sure the batteries are new and installed correctly.
After the installation of the batteries, there is no response when you press any button and no beeps are heard.
Check the cable connection and the polarity of the batteries. Also make sure the batteries are not dead.
I forgot my Master Codes.
Perform a reset in order to erase all passcodes. Once the reset is complete, all passcodes will be erased and the Master code
will return to the default value ( 12345678) .
Troubleshooting
Settings Factory Defaut
Master Code
Auto Lock
Silent Mode
Wrong Code Entry Limit
Shutdown Time
Vacation Mode
12345678
Disabled
Disabled
10 times
3 mins
Disabled
1. Keep the door open and unlocked.
2.Press and hold the Reset button, at the same time take out one battery and then place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of beep.
Restore To Factory Default Settings
This procedure will delete all User Codes associated with the lock.