Raptor E5 User manual

RAPTOR E5 - Quick StartR
APTOR

R
APTOR
R
APTOR
OVERVIEW
Rear cameraLoud speakerBattery doorBattery doorlocksMain screenPowerLight sensorExternal headsetEar phoneVolume +Volume -Menu softkeyUSB ConnectorMICBack softkeyHomeFront cameraLogo SpaceProgrammable buttonScanner buttonScanner buttonBarcode scanner

ACCESSORIES
Screen protector - Added protection for your device screen against knocks and scratches.Battery - Large 4000mAh battery and back door.The following accessories are included with every Raptor E5:Power supply - Country specific power supply used for charging.Vehicle Charger - 12/24v USB charger to charge device whilst in vehicle.USB Cable - USB cable for charging and syncing via PC or power supplies.

BUTTONS
Volume + - Increase volume of speaker and earpiece while in call.The Raptor E5 has six buttons which will make the use of your device much easier.Bellow there’s a list of the buttons and the respective descriptions.Volume - - Decrease volume of speaker and earpiece while in call.Power - Used to switch device on, or put/wake device into/out of standby mode.Home - The Android “Home” button brings the device to the home screen.Menu soft key - The Android “Menu” key brings up the menu feature and will behave differently depending on what app you are running at the time.Back soft key - The Android “Back” key will revert to the last app/page in the application stack running on the device.PowerVolume +Volume -Programmable buttonScanner buttonScanner button
R
APTOR
SOFT KEYSPHYSICAL KEYSProgrammable button - Can be assigned to any task or function using the E5’s API, PTT compatible.Scanner buttons - left and right scanner / RFID activate buttons.

Attaching the screen protector
Attach the screen protector following these instructions:All Raptors are provided with a screen protector which must be used in order to maintain the warranty of the device. A screen protector not only helps defend against scratches and knocks to the screen, but it will also help prolong the life of your device.A range of different protectors are avaiable for different purposes (privacy, anti glare, impact).Step 1: Check there isn’t already a screen protector on the device. Most Raptor smartphones have one pre-attached in the box.Step 2: Remove the old screen protector if necessary by simply peeling it of. Now make sure you clean the screen thoroughly to remove dirt, dust and any fluff that will create bubbles in the adhesion.Step 3: Peel the underside of the screen protector off, being careful not to let it touch anything.Step 4: Now carefully line up the top of the screen protector with the top of the device LCD. Carefullylet it drop onto the screen making sure it lines true all the way down to the bottom as you go. Use a credit card to smooth out any bubbles as you go.Step 5: Once you’re happy, peel off the top protective layer of the screen protector off and you’re done!
R
APTOR

R
APTOR
STATUS BAR ICONS
The Android OS of the Raptor E5 device is constantly monitoring for new notifications and status’ of the device. Apps can create there own icons but below are some of the more common ones with their meanings.Phone connection icons:Status bar with iconsOther icons:

CHARGING
The Raptor E5 can be charged in multiple ways:The Micro USB connector on the device along with the USB lead and chargers provided are used to charge your device safely.How to charge your device using a domestic charger:Step 1: Pull open the rubber cover at the bottom of the device marked with the USB symbol.Step 2: Insert the micro USB end of the provided USB cable carefully into the Micro-USB connector in the device. Please ensure you are careful when doing this as Micro-USB connectors can be easily damaged if not used correctly.Step 3: Plug the other side of the cable into either the USB-A socket of the domestic or vehicle charger.Please note: Only the supplied power units and cables must be used. Third party accessories have not been tested with Raptor devices and could cause electrical and physical harm to the connectors and the device. USB Connector
R
APTOR

CHARGING
The Raptor E5 can be charged in multiple ways:The rugged connector on the E5 allows for rugged, drop in charging with the E5 cradle. Thecradle will charge a device and spare battery at the same time.How to charge your device using a cradle charger:Step 1: Ensure there is nothing obstructing the connector on the device and pins on the cradle.Step 2: Plug the barrel connector cable, supplied with the cradle kit into the connector at the back of the cradle, ensureing the other side is plugged into the supplied USB power supply.Step 3: Slide the E5 device carefully into the cradle until you see the charge light or can see the battery icon change to the charging indicator.Please note: Only the supplied power units and cables must be used. Third party accessories have not been tested with Raptor devices and could cause electrical and physical harm to the connectors and the device.

SYNCING & CONNECTING ACCESSORIES
The Micro USB connector can also be used to connect and sync your device with other accessories or devices. You can connect either via the cradle or directly from, the device.How to connect your device with a PC:Step 1: Pull open the rubber cover at the bottom of the device marked with the USB symbol, or find the data USB connector on the underneath of the cradle.Step 2: Insert the micro USB end of the provided USB cable carefully into the Micro-USB connector in the device or cradle, ensuring you are careful when doing this, as Micro-USB connectors can be easily damaged if not used correctly.Step 3: Plug the other side of the USB cable into a free USB-A socket in your PC or laptop.Please note that the USB cable on the cradle will not charge the device, it will only pass data.Using an OTG (on the go) cable:Carefully connect the cable into the device exactly the same as described above. The other end of the OTG cable is a USB-A socket. You can now connect any device with a USB connector into this socket, such as a keyboard or barcode scanner, and the device should be able to automatically communicate with it.USB Connector
R
APTOR

CONNECTORS
The connectors allow external peripherals to be connected to the device. Read bellowa short explanation of the connectors and their location.
USB connector - Standard Micro-USB connector used for charging the device, syncing with a PC or to host USB communication via the supplied OTG cable.
External headset - Stereo DIN connector for use with supplied headset/MIC. It can be used for making phone calls and for listening to music on the device discretely.
External headset
All connectors have rubber covers which are required to maintain the IP rating of the device. To use the connector, simply pull up on the tab of the rubber cover, to expose the connector underneath.
R
APTOR
USB Connector