Raritan TMCAT17 series User manual

TMCAT QSG 1
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
TMCAT17®
Quick Setup Guide
Thank you for your purchase of the TMCAT17™, a 1U 17" LCD KVM switch, which enables you to control multiple
computers through a set of keyboard, touchpad (or mouse), and monitor.
This Quick Setup Guide explains how to install and configure the TMCAT17. For additional information on any aspect of
TMCAT17, see the TMCAT17 User Guide, which can be downloaded from the Firmware and Documentation section
(http://www.raritan.com/support/firmware-and-documentation/) of Raritan's website. Or you can access the product's
online help in the Product Online Help section (http://www.raritan.com/support/online-help/).
Package Contents
TMCAT17 switch x 1
Power cord x 1
Rackmount kit x 1 (including brackets and associated
screws)
* Mounting depth adjustable from 560 to 900 mm
Quick Setup Guide x 1
Warranty card x 1
If anything is missing or damaged, contact the local dealer or
Raritan Technical Support for help.
QS Rule
Structure Diagrams
Front View
1. Handle
2. Latches
3. LCD display
4. LCD controls
5. Support brackets
6. LCD power switch and LED
7. Touchpad mouse and buttons
8. Keyboard
9. Mounting ears
Rear View
1. Power socket
2. Power switch
3. Ground screw
4. User 2 port
5. Admin port
6. Channel ports (8 or 16 ports, depending on the model you
purchased)
7. Reset button
QS Rule
Before Installation
It is very important to locate the TMCAT17 in a suitable
environment.
The surface for placing and fixing the TMCAT17 should be
stable and level or mounted into a suitable cabinet.
Make sure the place has good ventilation, is out of direct
sunlight, away from sources of excessive dust, dirt, heat,
water, moisture, and vibration.

TMCAT QSG 2
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
Convenience for connecting the TMCAT17 to the related
facilities should be well considered too.
QS Rule
Rackmount Installation
Rackmount Kit
Component list
Mounting brackets
M6 cage nuts
M6 washers
M6 screws
Rack-Mounting the TMCAT17 Device
Before rack-mounting the device, make sure M6 cage nuts
have been inserted into the holes of vertical rails where you
intend to mount TMCAT17.
To rack-mount the device
Adjust the mounting brackets to fit the depth of your rack.
Attach them to vertical rails, using M6 screws and washers.
Leave all M6 screws slightly loose until you finish the
installation in Step 4.
Pick up TMCAT17.

TMCAT QSG 3
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
Line up the rear of support brackets on the TMCAT17 with
the front of mounting brackets installed in the rack.
Push TMCAT17 to make the support brackets slide into the
slots of mounting brackets.
Continue pushing TMCAT17 until the mounting ears
contact vertical rails.
Secure both mounting ears to vertical rails, using M6
screws and washers.
This step must be finished, or failure to complete it may
cause damage to the device.
Tighten all screws on both sides.
Installation completed.
QS Rule
Installing a Basic System
Preparing Requisite Items
Collect these components or devices before connecting
computers.
MCIMs or MCUTP cables (one per computer)
If using MCIMs, Cat5 UTP cables are required
The MCUTP cable is not compatible with Windows 98
operating system. Use MCIM for computers running
Windows 98.
Note: If the computer is a Sun server, you must prepare the
Sun USB MCUTP cable or DCIM-USB G2 instead of MCIM.
Connecting the Equipment
1. Turn OFF all devices, including the TMCAT17 switch and
computers.
2. Connect one MCIM or MCUTP cable to the computer.
If using MCIM-USB or USB MCUTP cable:
a. Plug the MCIM or MCUTP's USB connector into one of
the computer's available USB ports.
b. Plug the MCIM or MCUTP's video connector into the
computer's VGA port.
- OR -
If using MCIM-PS2 or PS/2 MCUTP cable:
a. Plug the MCIM or MCUTP's PS/2 mouse connector into
the computer's PS/2 mouse port.
b. Plug the MCIM or MCUTP's PS/2 keyboard connector
into the computer's PS/2 keyboard port.

TMCAT QSG 4
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
c. Plug the MCIM or MCUTP's video connector into the
computer's VGA port.
- OR -
If using the Sun USB MCUTP cable:
a. Plug the MCUTP's Sun USB connector into one of the
available USB ports on the Sun server.
b. Plug the MCUTP's video connector into the VGA port on
the Sun server.
Note: See Supporting Sun Servers in the User Guide for
more information.
3. Connect the computer to the TMCAT17 switch.
If using the MCIM:
a. Plug one end of a Cat5 UTP cable into the RJ-45 port of
the MCIM being connected with the computer.
b. Plug the other end of the Cat5 UTP cable into one of the
channel ports on the TMCAT17 switch.
If using the MCUTP cable:
Plug the MCUTP cable's RJ-45 connector into one
of the channel ports on the TMCAT17 switch.
4. Repeat Steps 2 to 3 to connect more computers.
5. (Optional) Connect the MCCAT user station to the User 2
port on the TMCAT17 switch via a standard Cat5 UTP
cable. For more information, see the Quick Setup Guide
shipped with the user station or the section titled
Connecting a User Station (Optional) in the User Guide.
Tip: The TMCAT17 switch is compatible with the Paragon
II enhanced user station, P2-EUST. If you have P2-EUST,
you can connect it, instead of the MCCAT user station, to
the TMCAT17 switch.
6. Connect an appropriate power cord to every device in the
system.
QS Rule
Using the TMCAT17 Switch
Opening TMCAT17
This section describes how to physically open the LCD KVM
switch when it is installed in a rack.
Note: The diagrams are for illustration, and may not look
exactly the same as the LCD KVM switch you purchased or the
rack in your workplace.

TMCAT QSG 5
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
To open the device:
1. Push the latches toward the center to unlock the assembly
of the LCD panel and keyboard tray.
2. Grasp the handle and pull the assembly out.
3. Flip up the LCD panel to a suitable angle.
4. Turn on the LCD KVM switch by pressing the power switch
on the rear panel.
5. Verify if the LCD's power LED is lit blue. If not, turn on the
LCD display by pressing the LCD's power switch at the
bottom of the LCD panel.
Login
The login mechanism prevents unauthorized users from
accessing the system or changing settings. To access any
computer, you may log in with any user account. To configure
the system settings on the Administration Menu, you must log
in with the administrator account.
Note: <XXX> shown in the diagrams represents the model
name, which varies according to the product you purchased.
To log in to the TMCAT17 system:
1. The Login box appears on the screen after turning ON the
TMCAT17 system.
2. Type your user name and password. For example, if you
are the administrator, the user name is "admin," and the
default password is "raritan."
a. Type admin in the User Name field, and press Enter.
b. Type raritan in the Password field, and press Enter.
The password is case sensitive.
3. The Selection Menu appears, indicating your login is
successful.
Important: It is strongly recommended to change the
default password for the security of your TMCAT17
system. For more information, see Changing Passwords
in the User Guide.

TMCAT QSG 6
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
Accessing a Computer or Channel
Use the Selection Menu to access any computer connected to
the TMCAT17 switch.
The first OSD menu that appears after login is the Selection
Menu, which does not show any channel name by default until
you assign them.
To select a channel on the Selection Menu:
1. If you do not find the channel on the current page, press
Page Down or Page Up to go to the next or previous page.
2. Press or to move the highlight bar to the channel you
want to select.
Tip: You can press the corresponding number shown in
the No column for that channel to quickly highlight it.
3. Press Enter.
The Selection Menu disappears. The video of the accessed
computer appears on the screen. You can control the computer
with the keyboard and mouse.
TMCAT17 switches do not support real-time channel
detection. Do NOT disconnect the current computer and
reconnect a different one to the channel you are accessing,
or you may have mouse or keyboard input issues with that
channel. When this occurs, re-select the channel on the
Selection Menu to solve the problem.
To select a different channel on the Selection Menu:
1. If you do not see the OSD on the screen, press the hot key
twice QUICKLY to activate it. The default hot key is Scroll
Lock.
2. Highlight another channel and press Enter.
For more information on the Selection Menu, see Selection
Menu in the User Guide.
Logout
After completing your tasks in the TMCAT17 system, you
should log out to prevent unauthorized people from accessing
the system.
To log out of the TMCAT17 system:
1. If you do not see the OSD on the screen, press the hot key
twice QUICKLY to activate it. The default hot key is Scroll
Lock.
2. Press F9.
The Login box appears, indicating that you have successfully
logged out.
Closing TMCAT17
This section describes how to close the LCD KVM switch
installed in a rack.
Note: The diagrams are for illustration, and may not look
exactly the same as the LCD KVM switch you purchased or the
rack in your workplace.
To close the TMCAT17 device:
1. Press down the LCD panel until it contacts the keyboard
tray.

TMCAT QSG 7
QSG-TMCAT-0D-v1.0-E 255-37-0122-00 RoHS
2. Push the assembly of the LCD panel and keyboard tray
back into the rack until you hear the click sound of latches.
Note: If the assembly is stuck and cannot be pushed back, then
push the black arrows on both sides while pushing back the
assembly.
QS Rule
Additional Information
For more information about the TMCAT17™and the entire
Raritan product line, see Raritan's website (www.raritan.com).
For technical issues, contact Raritan Technical Support. See
the Contact Support page in the Support section on Raritan's
website for technical support contact information worldwide.
Raritan's products use code licensed under the GPL and LGPL. You can request
a copy of the open source code. For details, see the Open Source Software
Statement at
(http://www.raritan.com/about/legal-statements/open-source-software-statement
/) on Raritan's website.