Raytec SPARTAN SPZ Series User manual

SPARTAN
Bulkhead & Flood BL24 Range - Installation Guide
SPX/SPZ
Zone 1 variant CML 13ATEX3007, IEC Ex CML14.0001 & CML21UKEX3099
Zone 2 variant CML 17ATEX4231, IEC Ex CML17.0135 & CML21UKEX4106
This installation guide provides instructions for installing the White-Light SPARTAN series
of explosion protected bulkheads.
Text in italics is specic for emergency variants.
Overview
1Safety Instructions
2Installation
3Maintenance
4 TechnicalSpecication
5Declaration of Conformity
TheSPARTANseriesofexplosionprotectedbulkheadsarespecialistdevices,certiedfor
useinspecicoperatingenvironments.
Theunitsmustbeinstalledinaccordancewiththeseinstructions,mustbecorrectlycertied
forthespecicoperatingenvironmentandmustbeinstalledbysuitablyqualiedpersonnel.
Ifyouhaveanyqueriesabouttheinstallationorthecerticationoftheunit–pleasecontact
Raytec for immediate assistance and advice.
Important information
0940-D-00007-Rev F

2www.raytecled.com UK / Europe Tel: [phone]
Americas Tel: [phone]
1. Safety instructions
1. Readthis leaet carefully before commencing to install the SPARTANBulkheadunitandretainitfor
futureuse.Installationcanonlybecarriedoutbysuitablyqualiedpersonnel.
2. Checkthecerticationnameplateattachedtotheluminairetoensurethatthehazardouszone,mains
supply, ambient temperature present and ‘T’ rating are suitable for the environment the unit is being
installed in.
3. If the SPARTAN unit is to be installed in areas of high vibration, please consult with Raytec.
4. Externally the SPARTAN unit housing is constructed from marine grade aluminium, and toughened
glass, stainless steel brackets/fasteners and silicone gaskets, internally there are many non metallic
components. The end user must ensure that these materials are suitable for the environment the
SPARTANunitwillbeinstalledin;Zone1andZone2Hazardousareas.
5. SPARTAN units are designed to withstand marine environments and are tested in accordance with
IEC60068-2-52. However if the SPARTAN unit is to be installed in a very high corrosive environment
such as coastal and offshore the following good practice should be followed:
During installing ensure there are no scratches, chips or defects in external paint surface that
would allow ingress of water to bare aluminium. If so touch up with suitable paint
During installation apply an anti corrosive jointing compound to screw threads such as PSU cover
and external earth points.
During installation ensure exterior surface of the product is not in direct contact with a dissimilar
metalsuchasgalvanisedsteel.Ifsotanylonbarriertopreventgalvaniccorrosion.
During maintenanceregularlywashdownexternalsurfaceofttingwithclean,freshwaterto
remove any deposits of mineral salts on the exterior surface.
6. Checkcertication nameplate on sideof bulkhead to ascertaintype of threaded cableentry on the
luminaire. Select suitably certied ATEX/IEC Ex/UKEX cable glands and stopper plugs, these must
beparallelthread,haveaminimumof5fullthreadengagementandbeofamedium/netoleranceto
ISO965-1 and ISO965-3. The cable entry devices selected must maintain the IP rating of the luminaire
7. The incoming mains cable should not exceed a temperature rise of 24°C above the ambient conditions;
select suitable cable.
8. When the unit is installed correctly and in accordance with these installation instructions it will not harm
humans or animals
9. Before installing emergency luminaires please check the last charge date of the battery. This is shown
on the external product packaging and also on the battery label, alternatively consult date shown on
thedeclarationatthebackofthisleaet.Ifthelastchargedatewasinexcessof3months(ifstoredat
5°Cto25°C)or1month(ifstoredoutsidethisrange)fromdateofinstallation,pleaseconsultRaytec
document 0010-D-00001 Battery Handling Guide
!
Install in a well
ventilated area
Do not continually
stare at lamp
Isolate mains before
removing cover
1.5 m

3www.raytecled.comUK / Europe Tel: [phone]
Americas Tel: [phone]
2. Installation
Mounting SPARTAN Bulkhead Unit
1. TomeettherequirementsofcerticationaMINIMUMof2xingpointsmustbeused,
thexingpointsmustbesuitablefortheconditionsofuse.Raytecrecommendusing
M6MarineGradeA4StainlessSteelxings(notsupplied)
121
104
302
288
204
220 182
240
220
168
70
20
17
3

4www.raytecled.com UK / Europe Tel: [phone]
Americas Tel: [phone]
1. ATTACH2-OFFL-BRACKET(ITEM2)TOVACANTFIXINGHOLESONREAROFBULKHEAD
BODY,USING4-OFFM6X12SCREWS(ITEM5)&M6SPRING-WASHER(ITEM6)ASSHOWN.
2. ALIGNSTIRRUPBRACKET(ITEM7)WITHL-BRACKETS,POSITIONM8FIBREWASHER(ITEM
1) BETWEEN BOTH BRACKETS AND FIT M8 SCREW(ITEM 3)WITH M8 SPRING-
WASHER(ITEM4)TOBOTHSIDESOFSTIRRUPASSHOWNBELOWANDFULLYTIGHTEN.
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING REMAINING M6 SREW,
SPRING-WASHERANDNUT(ITEM9)
SPARTAN Flood BL24 Mounting Instructions
FIBRE WASHER
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW AND SPRING-WASHER.
9
6
8
4
5
2
7
1
3
6
3
46
5
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW, SPRING-WASHER AND NUT (ITEM 9)
FIBRE WASHER
1. ATTACH 2-OFF L-BRACKET(ITEM 2) TO VACANT FIXING HOLES ON
REAR OF BULKHEAD BODY, USING 4-OFF M6X12 SCREWS(ITEM 5) &
M6 SPRING-WASHER(ITEM 6) AS SHOWN.
2. ALIGN STIRRUP BRACKET(ITEM 7) WITH L-BRACKETS, POSITION
M8 FIBRE WASHER(ITEM 1) BETWEEN BOTH BRACKETS AND FIT M8
SCREW(ITEM 3)WITH M8 SPRING-WASHER(ITEM 4)TO BOTH SIDES
OF STIRRUP AS SHOWN BELOW AND FULLY TIGHTEN.
ITEM NO. DESCRIPTION QTY.
1
M8 FIBRE WASHER
2
2
L-BRACKET
2
3
M8X20 SOCKET CAP
2
4
M8 SPRING WASHER
2
5
M6X12 SOCKET CAP
4
6
M6 SPRING WASHER
5
7
STIRRUP BRACKET
1
8
M6X20 SOCKET CAP
1
9
M6 NUT St/Steel 1
REVISION
ALL DIMENSIONS IN MM.
Tel: [phone].
Fax: [phone] .
DRAWN
CHK'D
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
TOLERANCES: (LINEAR)
XXX +/- 0.5mm
XXX.X +/- 0.1mm
ANGULAR: +/- 0.5°
FINISH:
DEBUR AND
BREAK SHARP
EDGES
NAME SIGNATURE DATE MATERIAL:
DO NOT SCALE DRAWING
TITLE:
DWG NO.
SCALE
1
A3
WEIGHT:
A
B
A
8 7 6 4
D
C
5 1 2 3
A
B
4 3 2 1
C
F
E
D
F
E
IF IN DOUBT ASK
8 7 6 5
1
SHEET
OF SHEETS
D.Bloxham
Unit 3 Wansbeck Business Park,
Rotary Parkway.
Ashington.
Northumberland. NE63 8QW. UK.
SHEET
A
27/10/2021
SPX-BKT-BLST30
BULKHEAD STIRRUP BRACKET KIT
940-A-00044
CERTIFICATE RELATED DRAWING
NO MODIFICATIONS ALLOWED
WITHOUT THE APPROVAL OF THE
AUTHORISED PERSON.
IF IN DOUBT ASK!
B.Thompson
27/10/2021
FIBRE WASHER
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW AND SPRING-WASHER.
9
6
8
4
5
2
7
1
3
6
3
46
5
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW, SPRING-WASHER AND NUT (ITEM 9)
FIBRE WASHER
1. ATTACH 2-OFF L-BRACKET(ITEM 2) TO VACANT FIXING HOLES ON
REAR OF BULKHEAD BODY, USING 4-OFF M6X12 SCREWS(ITEM 5) &
M6 SPRING-WASHER(ITEM 6) AS SHOWN.
2. ALIGN STIRRUP BRACKET(ITEM 7) WITH L-BRACKETS, POSITION
M8 FIBRE WASHER(ITEM 1) BETWEEN BOTH BRACKETS AND FIT M8
SCREW(ITEM 3)WITH M8 SPRING-WASHER(ITEM 4)TO BOTH SIDES
OF STIRRUP AS SHOWN BELOW AND FULLY TIGHTEN.
ITEM NO. DESCRIPTION QTY.
1
M8 FIBRE WASHER
2
2
L-BRACKET
2
3
M8X20 SOCKET CAP
2
4
M8 SPRING WASHER
2
5
M6X12 SOCKET CAP
4
6
M6 SPRING WASHER
5
7
STIRRUP BRACKET
1
8
M6X20 SOCKET CAP
1
9
M6 NUT St/Steel 1
REVISION
ALL DIMENSIONS IN MM.
Tel: [phone].
Fax: [phone] .
DRAWN
CHK'D
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
TOLERANCES: (LINEAR)
XXX +/- 0.5mm
XXX.X +/- 0.1mm
ANGULAR: +/- 0.5°
FINISH:
DEBUR AND
BREAK SHARP
EDGES
NAME SIGNATURE DATE MATERIAL:
DO NOT SCALE DRAWING
TITLE:
DWG NO.
SCALE
1
A3
WEIGHT:
A
B
A
8 7 6 4
D
C
5 1 2 3
A
B
4 3 2 1
C
F
E
D
F
E
IF IN DOUBT ASK
8 7 6 5
1
SHEET
OF SHEETS
D.Bloxham
Unit 3 Wansbeck Business Park,
Rotary Parkway.
Ashington.
Northumberland. NE63 8QW. UK.
SHEET
A
27/10/2021
SPX-BKT-BLST30
BULKHEAD STIRRUP BRACKET KIT
940-A-00044
CERTIFICATE RELATED DRAWING
NO MODIFICATIONS ALLOWED
WITHOUT THE APPROVAL OF THE
AUTHORISED PERSON.
IF IN DOUBT ASK!
B.Thompson
27/10/2021
FIBRE WASHER
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW AND SPRING-WASHER.
9
6
8
4
5
2
7
1
3
6
3
46
5
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW, SPRING-WASHER AND NUT (ITEM 9)
FIBRE WASHER
1. ATTACH 2-OFF L-BRACKET(ITEM 2) TO VACANT FIXING HOLES ON
REAR OF BULKHEAD BODY, USING 4-OFF M6X12 SCREWS(ITEM 5) &
M6 SPRING-WASHER(ITEM 6) AS SHOWN.
2. ALIGN STIRRUP BRACKET(ITEM 7) WITH L-BRACKETS, POSITION
M8 FIBRE WASHER(ITEM 1) BETWEEN BOTH BRACKETS AND FIT M8
SCREW(ITEM 3)WITH M8 SPRING-WASHER(ITEM 4)TO BOTH SIDES
OF STIRRUP AS SHOWN BELOW AND FULLY TIGHTEN.
ITEM NO. DESCRIPTION QTY.
1
M8 FIBRE WASHER
2
2
L-BRACKET
2
3
M8X20 SOCKET CAP
2
4
M8 SPRING WASHER
2
5
M6X12 SOCKET CAP
4
6
M6 SPRING WASHER
5
7
STIRRUP BRACKET
1
8
M6X20 SOCKET CAP
1
9
M6 NUT St/Steel 1
REVISION
ALL DIMENSIONS IN MM.
Tel: [phone].
Fax: [phone] .
DRAWN
CHK'D
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
TOLERANCES: (LINEAR)
XXX +/- 0.5mm
XXX.X +/- 0.1mm
ANGULAR: +/- 0.5°
FINISH:
DEBUR AND
BREAK SHARP
EDGES
NAME SIGNATURE DATE MATERIAL:
DO NOT SCALE DRAWING
TITLE:
DWG NO.
SCALE
1
A3
WEIGHT:
A
B
A
8 7 6 4
D
C
5 1 2 3
A
B
4 3 2 1
C
F
E
D
F
E
IF IN DOUBT ASK
8 7 6 5
1
SHEET
OF SHEETS
D.Bloxham
Unit 3 Wansbeck Business Park,
Rotary Parkway.
Ashington.
Northumberland. NE63 8QW. UK.
SHEET
A
27/10/2021
SPX-BKT-BLST30
BULKHEAD STIRRUP BRACKET KIT
940-A-00044
CERTIFICATE RELATED DRAWING
NO MODIFICATIONS ALLOWED
WITHOUT THE APPROVAL OF THE
AUTHORISED PERSON.
IF IN DOUBT ASK!
B.Thompson
27/10/2021

5www.raytecled.comUK / Europe Tel: [phone]
Americas Tel: [phone]
FIBRE WASHER
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW AND SPRING-WASHER.
9
6
8
4
5
2
7
1
3
6
3
46
5
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW, SPRING-WASHER AND NUT (ITEM 9)
FIBRE WASHER
1. ATTACH 2-OFF L-BRACKET(ITEM 2) TO VACANT FIXING HOLES ON
REAR OF BULKHEAD BODY, USING 4-OFF M6X12 SCREWS(ITEM 5) &
M6 SPRING-WASHER(ITEM 6) AS SHOWN.
2. ALIGN STIRRUP BRACKET(ITEM 7) WITH L-BRACKETS, POSITION
M8 FIBRE WASHER(ITEM 1) BETWEEN BOTH BRACKETS AND FIT M8
SCREW(ITEM 3)WITH M8 SPRING-WASHER(ITEM 4)TO BOTH SIDES
OF STIRRUP AS SHOWN BELOW AND FULLY TIGHTEN.
ITEM NO. DESCRIPTION QTY.
1
M8 FIBRE WASHER
2
2
L-BRACKET
2
3
M8X20 SOCKET CAP
2
4
M8 SPRING WASHER
2
5
M6X12 SOCKET CAP
4
6
M6 SPRING WASHER
5
7
STIRRUP BRACKET
1
8
M6X20 SOCKET CAP
1
9
M6 NUT St/Steel 1
REVISION
ALL DIMENSIONS IN MM.
Tel: [phone].
Fax: [phone] .
DRAWN
CHK'D
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
TOLERANCES: (LINEAR)
XXX +/- 0.5mm
XXX.X +/- 0.1mm
ANGULAR: +/- 0.5°
FINISH:
DEBUR AND
BREAK SHARP
EDGES
NAME SIGNATURE DATE MATERIAL:
DO NOT SCALE DRAWING
TITLE:
DWG NO.
SCALE
1
A3
WEIGHT:
A
B
A
8 7 6 4
D
C
5 1 2 3
A
B
4 3 2 1
C
F
E
D
F
E
IF IN DOUBT ASK
8 7 6 5
1
SHEET
OF SHEETS
D.Bloxham
Unit 3 Wansbeck Business Park,
Rotary Parkway.
Ashington.
Northumberland. NE63 8QW. UK.
SHEET
A
27/10/2021
SPX-BKT-BLST30
BULKHEAD STIRRUP BRACKET KIT
940-A-00044
CERTIFICATE RELATED DRAWING
NO MODIFICATIONS ALLOWED
WITHOUT THE APPROVAL OF THE
AUTHORISED PERSON.
IF IN DOUBT ASK!
B.Thompson
27/10/2021
FIBRE WASHER
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW AND SPRING-WASHER.
9
6
8
4
5
2
7
1
3
6
3
46
5
3. POSITION STIRRUP TO PREFERRED ANGLE AND SECURE USING
REMAINING M6 SREW, SPRING-WASHER AND NUT (ITEM 9)
FIBRE WASHER
1. ATTACH 2-OFF L-BRACKET(ITEM 2) TO VACANT FIXING HOLES ON
REAR OF BULKHEAD BODY, USING 4-OFF M6X12 SCREWS(ITEM 5) &
M6 SPRING-WASHER(ITEM 6) AS SHOWN.
2. ALIGN STIRRUP BRACKET(ITEM 7) WITH L-BRACKETS, POSITION
M8 FIBRE WASHER(ITEM 1) BETWEEN BOTH BRACKETS AND FIT M8
SCREW(ITEM 3)WITH M8 SPRING-WASHER(ITEM 4)TO BOTH SIDES
OF STIRRUP AS SHOWN BELOW AND FULLY TIGHTEN.
ITEM NO. DESCRIPTION QTY.
1
M8 FIBRE WASHER
2
2
L-BRACKET
2
3
M8X20 SOCKET CAP
2
4
M8 SPRING WASHER
2
5
M6X12 SOCKET CAP
4
6
M6 SPRING WASHER
5
7
STIRRUP BRACKET
1
8
M6X20 SOCKET CAP
1
9
M6 NUT St/Steel 1
REVISION
ALL DIMENSIONS IN MM.
Tel: [phone].
Fax: [phone] .
DRAWN
CHK'D
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
TOLERANCES: (LINEAR)
XXX +/- 0.5mm
XXX.X +/- 0.1mm
ANGULAR: +/- 0.5°
FINISH:
DEBUR AND
BREAK SHARP
EDGES
NAME SIGNATURE DATE MATERIAL:
DO NOT SCALE DRAWING
TITLE:
DWG NO.
SCALE
1
A3
WEIGHT:
A
B
A
8 7 6 4
D
C
5 1 2 3
A
B
4 3 2 1
C
F
E
D
F
E
IF IN DOUBT ASK
8 7 6 5
1
SHEET
OF SHEETS
D.Bloxham
Unit 3 Wansbeck Business Park,
Rotary Parkway.
Ashington.
Northumberland. NE63 8QW. UK.
SHEET
A
27/10/2021
SPX-BKT-BLST30
BULKHEAD STIRRUP BRACKET KIT
940-A-00044
CERTIFICATE RELATED DRAWING
NO MODIFICATIONS ALLOWED
WITHOUT THE APPROVAL OF THE
AUTHORISED PERSON.
IF IN DOUBT ASK!
B.Thompson
27/10/2021

6www.raytecled.com UK / Europe Tel: [phone]
Americas Tel: [phone]
2. The SPARTAN Bulkhead is supplied as standard with the mounting brackets as shown
ontheabovediagram,othermountingmethods/bracketsavailable–pleasecontact
Raytec.
Spartan Bulkhead Standard/Emergency Variant
3. Installershouldearththeunitseparately–aninternalandexternalearthpointare
provided as standard
4. Connect wires to mains supply.
5. Iftheunitisopenedforanyreason,disconnectmains–On emergency luminaires
there may be more than one mains supply
6. All SPARTAN bulkheads have terminal blocks suitable for looping 4mm2 cable,
only one cable should be connected to each terminal block connection
WiretheMainscableintotheterminalblock.Provisionhasbeenmadeforthisandidentied
astheE(Earth),L1(Liveswitched),L2(Livepermanent)andN(Neutral)terminals.There
are two pairs of contacts for each of these to facilitate a mains cable that can be looped in
and out of the unit. The L2 terminals on a standard unit are not electrically connected but
allows them to be used on the same circuits as emergency bulkheads.
NEL1 L2
EARTHTOSCREW
PSU
WHITE/RED
WHITE
BLUE
BROWN
GREEN
TO LED's
Typical wiring diagram - Standard Variants
Typical wiring diagram - Emergency Variants
NEL1 L2
EARTHTOSCREW
PSU
WHITE/RED
WHITE
BLUE
BROWN
GREEN
TO LED's
BATTERY
RED
RED
BLACK
BLACK
FUSE
GREY
REMOVELINK IF4-CORE CABLEUSE
D

7www.raytecled.comUK / Europe Tel: [phone]
Americas Tel: [phone]
Operation
Thelightttingwillcarryoutthefollowingfunctionautomatically after installation:
• Commissioning Cycle
• Function test
• Self-test
Atri-colourLEDindicatordisplaysthelightttingstatus.Theindicationcoloursareshown
in table 1.
a. Commissioning Cycle
• Starts automatically after 24 hours of uninterrupted charging. If there is a mains
failure in this time the count resets for another 24 hours.
• 3 charge/discharge cycles to optimise battery’s full capacity.
• Battery is charged for 24 hours before each discharge cycle.
• No need for manual commissioning
b. Function Test
• Carried out every 7 days.
• Checks the function of the battery, lamp and power supply.
• Lasts for few minutes only.
Spartan Intelligent Emergency Operation Guide
7. The battery fuse located within the Bulkhead housing on emergency variants is
disconnected after nal manufacturing testing. When installing the bulkhead the
battery fuse will need to be reconnected and the unit charged for 24 hours and then
discharged (repeated 3 times) to bring the battery up to peak capacity. (Unless an
‘EMX’ intelligent emergency variant – see notes below)
8. If a 4 core cable is used on emergency luminaires – L1, L2, N and E the link cable
at the front of the terminal block between L1 and L2 should be removed
9. During emergency operation the light output and duration will be determined by the
variant purchased
10. If carrying out Insulation Resistance tests the normal method of insulation testing
is to connect Live and Neutral together and test between this point and Earth to
prevent the risk of damage to the electronic control gear.

8www.raytecled.com UK / Europe Tel: [phone]
Americas Tel: [phone]
Notes
• Theluminairewillswitchoffmomentarily(<0.5sec)duringthetransitionbetweena
test and normal operation.
• If a test was interrupted by a mains failure, the test will be halted, and the unit will
enter emergency mode. Once the mains supply is back, the unit will allow 24 hours
to recharge the battery before continuing the tests.
• The self-test is carried out at a random time to eliminate the possibility of having more
than one unit undergoing the test at the same time.
LED indication
c. Self-test
• Carried out at a random time every 3 months.
• Checks the battery’s capacity and lamp’s condition.
• Performs self-recovery for the battery if not at peak capacity.
• Is carried out at 100% load
• Discharges only 2/3 of the battery’s capacity.
LED Indication Condition
Static Amber Commissioning in progress
Flashing Amber
Discharge cycle in progress
LEDwillashinrelevantcolourwhiledischarging
Static Red
Battery defective/Fuse blown
PSU error
Battery not at peak capacity
Light engine failure
No light Emergency mode activated
Static Green Commissioning completed

9www.raytecled.comUK / Europe Tel: [phone]
Americas Tel: [phone]
3. Maintenance
1. It is essential that all SPARTAN Bulkhead units are maintained in accordance with
therequirementsoftheEN60079-17standard:(Electricalapparatusforexplosivegas
atmospheres–otherthanmines).
2. IMPORTANT.  No modications are permitted to the unit, all spare parts must be
purchased from the manufacturer, unauthorized modications or spare parts will
invalidatecerticationandmaketheequipmentdangerous.
3. Isolate the SPARTAN Bulkhead from the mains supply and allow to cool before
carrying out any maintenance work.
• ForEmergencyvariants,batterymustbeisolated/connectedwhenahazardous
environment is NOT present prior to carrying out any maintenance work.
4. In the unlikely event of a number of LED’s failing, the light engine assembly must be
replaced. This is achieved by loosening front cover bolts, disconnecting the white
LED cables to power supply, remove four M6 bolts from rear of light engine and pull
the light engine assembly clear. Re tting a light engine is a reversal of the above
procedure.
5. The unit has one independent power supply, in the event that the power supply
needs to be replaced the cables to the LED and mains terminal block will need to
be disconnected, the four M6 bolts released, then the power supply can then be
removed. Fitting a new power supply is a reversal of the above procedure.
6. Disposal of packaging, SPARTAN unit and old LED assemblies should be carried out
in accordance with national regulations.
PROTECTION/CERTIFICATION
CML13ATEX3007,IECExCML14.0001&CML21UKEX3099
II 2 GD Ex eb mb IIC T4 Gb
Ta-52°Cto+55°C(standardvariants)
II 2 GD Ex eb mb IIC T4 Gb
Ta-20°Cto+46°C(emergencyvariants)
Ex tb IIIC T98°C Db
IP66 & IP67 Ta = -52°C to +55°C
110V-254VACor18-48VAC/18-69VDC
CML17ATEX4231,IECExCML17.0135&CML21UKEX4106
II 3 GD Ex ec mc IIC T4 Gc
Ta-50°Cto+55°C(standardvariants)
II 3 GD Ex ec mc IIC T4 Gc
Ta-20°Cto+55°C(emergencyvariants)
Ex tc IIIC T98°C Dc
IP66 & IP67 Ta = -50°C to +55°C
110V-254VACor18-48VAC/18-69VDC

10 www.raytecled.com UK / Europe Tel: [phone]
Americas Tel: [phone]
4. Technical Specication
BL24-STD BL24-EM
Input Voltage 110-254VAC
Input Current (230Vac, full load) 0.15A 0.16A
Consumption 20W/34W 24W/37W
Power Factor (230Vac, full load) >0.97
Mains Frequency 50/60Hz
Inrush Current (Ipeak @50%) 20A,∆t<300µs
Total Harmonic Distortion (230Vac, full load) <10%
IP Rating IP66/67
Weight (std) 5Kg 6Kg
Dimensions See previous pages for line diagrams
ATEX and IECEx and UKEX Rating See above
Twidth
Inrush Current Typical Curve
Ipeak