Razor TURBO JETTS User manual

OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
TURBO JETTS™
ELECTRIC HEEL WHEELS

CONTENTS
1
CONTENTS
Safety Warnings ...........................................................................................1-2
Before You Begin.............................................................................................. 3
Assembly and Set-Up....................................................................................4-5
Charging the Battery........................................................................................ 6
Pre-Ride Checklist............................................................................................ 6
Usage ............................................................................................................... 7
Repair and Maintenance.............................................................................8-10
Troubleshooting Guide ................................................................................... 11
Razor Turbo Jetts Electric Heel Wheels Parts ..........................................12-13
Warranty and Contact Information................................................................ 15
SAFETY WARNINGS
WARNING: Riding Razor Turbo Jetts Electric Heel Wheels does
present potential risks and caution is required. Like any riding product, Razor
Turbo Jetts Electric Heel Wheels have inherent hazards associated with their
use (for example, falling or riding it into a hazardous situation). Like any riding
product, Razor Turbo Jetts Electric Heel Wheels can and are intended to move
and it is therefore, of course, possible to lose control or otherwise get into
dangerous situations. Both children, and adults responsible for supervising
them, must recognize that if such things occur, a rider can be seriously injured
or die even when using safety equipment and other precautions. RIDE AT
YOUR OWN RISK AND USE COMMON SENSE.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY: Because products, like Razor Turbo Jetts
Electric Heel Wheels, can and do present potential hazards plainly associated
with their use, it is well recognized THE NEED FOR EXERCISE OF PARENTAL
RESPONSIBILITY IN SELECTING RIDING PRODUCTS APPROPRIATE TO THE
AGE OF A CHILD, OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH
CHILDREN OF VARIOUS AGES MAY HAVE ACCESS TO THE SAME RIDING
PRODUCTS, IS IMPORTANT. Not every product is appropriate for every age
or size of child, and different age recommendations are found within
categories of product which are intended to reflect the nature of the hazards
and the expected mental or physical ability, or both, of a child to cope with
the hazards.
WARNING: NOT FOR RIDERS UNDER AGE 9 OR HEAVIER
THAN 176 LB (80 KG). DO NOT EXCEED THE WEIGHT LIMIT OF 176 lb
(80 kg) – including backpacks and other items that might be carried.
Exceeding the weight limit could injure the rider and damage the Razor Turbo
Jetts Electric Heel Wheels. Rider weight alone also does not necessarily
mean a person’s size is appropriate to fit or maintain control of the Razor
Turbo Jetts Electric Heel Wheels. Keep this product away from small
children and remember that this product is intended for use only by persons
who are, at a minimum, completely comfortable and competent while
operating the product.
Razor recommends that children under the age of 9 not be permitted to
use this product. This recommendation is based not just on age or weight
or height; it reflects consideration of expected maturity and skills as well
as physical size. The recommended rider age of 9 years or older is only an
estimate and can be affected by the rider’s size, weight, or skills – not every
rider 9 years old or older will be suited to the product. Certainly, any rider
unable to fit comfortably on the Razor Turbo Jetts Electric Heel Wheels
should not attempt to ride them, but a parent’s decision to allow his or
her child to ride this product should be based on the child’s maturity,
skill, and ability to follow rules. Razor emphasizes that adults are
strongly advised not to disregard Razor’s recommendations or permit
younger children to ride the Razor Turbo Jetts Electric Heel Wheels.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in the use of any ride-on product, should not
use or be permitted to use products inappropriate for their abilities. Persons
with heart conditions, head, back or neck ailments (or prior surgeries to these
areas of the body), or pregnant women, should be cautioned not to operate
such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 176 lb (80 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the Razor Turbo Jetts Electric Heel Wheels.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Before use, check to confirm that covers and guards are in place and in
serviceable condition. Check that the wheels are free of flat spots from
wear. The product should be maintained and repaired in accordance with
the manufacturer’s specifications, using only the manufacturer’s authorized
replacement parts, and should not be modified from the manufacturer’s
original design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the Razor Turbo Jetts Electric Heel Wheels
may be used. Keep safely away from cars and motor vehicle traffic at
all times. Only use where allowed and with caution.
Do not activate the motor of the Razor Turbo Jetts Electric Heel Wheels
unless you are in a safe, outdoor environment suitable for riding. Razor Turbo
Jetts Electric Heel Wheels must be moving at least 3 mph (5 km/h) with
the drive wheel engaged with the ground before the motor will start.
To push/kick start the Razor Turbo Jetts Electric Heel Wheels before engaging
motor, it is recommended that the rider place the motorized side on the
forward foot and push start using the front of the rear foot
(see page 7).
The normal powered top speed of this product will be approximately 10 mph
(16 km/h), which can be affected by conditions, such as rider weight, inclines
and battery charge level. Avoid excessive speeds that can be associated with
downhill rides.
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
The Razor Turbo Jetts Electric Heel Wheels is intended for use on flat, dry
surfaces, such as pavement or level ground, without loose debris, such as
sand, leaves, rocks or gravel. Wet, slick, bumpy, uneven or rough surfaces may
impair traction and contribute to possible accidents. Do not ride your product
in mud, ice, puddles or water. Watch out for potential obstacles that could
catch your wheel or force you to swerve suddenly or lose control. Avoid sharp
bumps, drainage grates, and sudden surface changes.
Do not attempt or do stunts or tricks. The Razor Turbo Jetts Electric Heel
Wheels are not made to withstand abuse from misuse, such as jumping, curb
grinding or any other type of stunts. Racing, stunt riding, or other maneuvers
also enhance risk of loss of control, or may cause uncontrolled rider actions
or reactions.
Never allow more than one person at a time to ride the product.
Do not ride at night or when visibility is limited.
Never use near steps or swimming pools.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to come
in contact with moving parts or wheels while the motor is engaged.
Do not touch the electric motor or wheels on your product when in use (or
after using) as they can become very hot.
Never use headphones or a cell phone to talk or text when riding.

2
SAFETY WARNINGS
Never hitch a ride with a vehicle.
Do not ride your product in wet or icy weather and never immerse in water,
as the electrical and drive components could be damaged by water or create
other possibly unsafe conditions. Never risk damaging surfaces, such as
carpet or flooring, by use of a Razor Turbo Jetts Electric Heel Wheels indoors.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads, kneepads and wrist guards. A
helmet may be legally required by local law or regulation in your area. A long-
sleeved shirt, long pants, and gloves are recommended. Always wear athletic
shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of
the way of the wheels and motor. Never ride barefooted or in sandals.
USING THE CHARGER
The charger supplied with the product should be regularly examined for
damage to the cord, plug, enclosure and other parts. In the event of such
damage, the product must not be charged until the charger has been repaired
or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from product when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
product with damp cloth.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE
AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
3
Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect
the contents of the box for scratches, or dents that may have occurred during shipping. Because the Razor Turbo Jetts
Electric Heel Wheels are assembled and packed at the factory, there should not be any problems, even if the box has a
few scars or dents.
MAKE SURE POWER SWITCH IS TURNED “OFF” AND BATTERY IS REMOVED BEFORE CONDUCTING ANY
ASSEMBLY OR MAINTENANCE PROCEDURES.
Estimated Adjustment and Set-UpTime
Allow up to 5 minutes for set up & adjustment, not including initial charge time.
Allow up to 3 hours for charge (see page 6 for charging information).
WARNING:
DO NOT USE NON-RAZOR
PRODUCTS WITH YOUR
RAZOR TURBO JETTS
ELECTRIC HEEL WHEELS.
The Razor Turbo Jetts Electric
Heel Wheels have been built
to certain Razor design
specifications. The original
equipment supplied at the time
of sale was selected on the
basis of its compatibility with
the frame and all other parts.
Certain aftermarket products
may not be compatible and will
void the warranty.
Note: Razor Turbo Jetts
Electric Heel Wheels must be
moving at least 3 mph (5 km/h)
with the drive wheel engaged
with the ground before the
motor will start.
Product ID Locations:
(See locations to the left)
1. Inside of Motorized Side Of
Turbo Jetts. (Not Shown)
2. Battery
3. Charger
4. UPC Side of Box (Not Shown)
Box Contents:
• Razor Turbo Jetts Electric
Heel Wheels
• Charger
• Owner’s Manual
• Rubber Heel Insert
3.
Adjustable Ankle Strap
Non-Motorized Side
Motorized Side
Adjustable Ankle Strap
Adjustable Frame
Adjustable Frame
Motor
2.
1.
Drive Wheel
Charger
(Note: Charger design may
vary from one shown)
BEFOREYOU BEGIN

B
A
B
A
B
A
B
A
Non-Motorized Side
Motorized Side
5 Follow the direction of the arrow
to insert foot. Place foot in Turbo
Jetts and push the frame from
both sides until it clicks into place
snuggly fitting width of shoe.
Note: Adjustment must be done
while wearing recommended
appropriate footwear.
6 Pull tab down to secure the
strap. Align and press together hook
and pile sides of the strap. Make
sure it is completely secure.
4
ASSEMBLY AND SET-UP
Adjusting the Turbo Jetts
WARNING: Failure to properly adjust the Turbo Jetts may cause the user to lose control and fall.
2 To make strap shorter: Pull
the outer strap first (B), then the
inner strap (A).
2 To make strap shorter: Pull
the outer strap first (B), then the
inner strap (A).
1To make strap longer: Pull the
inner strap first (A), then the outer
strap (B).
1 To make strap longer: Pull the
inner strap first (A), then the outer
strap (B).
5 Center stap pad and pull stap
snug.
Note: Adjustment must be done
while wearing recommended
appropriate footwear.
3 Press the button and pull the
frame to its maximum width.
3 Press the button and pull the
frame to its maximum width.
6 Pull tab down to secure the
strap. Align and press together hook
and pile sides of the strap. Make
sure it is completely secure.
4 Place foot in Turbo Jetts and
push the frame from both sides until
it clicks into place snuggly fitting
width of shoe.
4 Place foot in Turbo Jetts and
push the frame from both sides until
it clicks into place snuggly fitting
width of shoe.

5
ASSEMBLY AND SET-UP
Adding Rubber Heel Insert
Peel the back of the adhesive and place in the heel area of the frame. Use the rubber heel inserts to customize the fit
between the frame and the shoe. The insert can also help adjust the activation and ride angle.

6
CHARGING THE BATTERY
PRE-RIDE CHECKLIST
Wheels
Periodically inspect the wheels for excessive wear. Wheels are
not covered under your limited warranty.
Frame
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb
or object and wreck, crack or break a frame. Get in the habit of
inspecting your product on a regular basis.
Hardware/Loose Parts
Check and secure all fasteners before every ride. Make sure
the strap is adhered properly in place before using. Before
every ride, check all parts, such as nuts, bolts, fasteners, etc., to
ensure they are secure and assembled correctly. There should
not be any unusual rattles or sounds from loose parts or broken
components. If the product is damaged, do not ride. Reference
“Safety Warnings” on pages 1 and 2 of
this manual.
Safety Gear
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads, kneepads and wrist guards are recommended.
Always wear athletic shoes (lace-up shoes with rubber soles) and
keep shoelaces tied and out of the way of the wheels, motor and
drive system. NEVER RIDE BAREFOOTED OR IN SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for product use. Check with your insurance
company for information regarding insurance.
Be Careful!
This product is not for aggressive or trick use. Avoid steep inclines
and don’t roll too fast — you can lose control and fall. Skate
parks are not designed for young users. Never use in traffic or on
the street and watch your surroundings for pedestrians, bikers,
boarders and skaters.
WARNING: Use ONLY
with the recommended charger.
Batteries are only to be charged
under adult supervision. The
charger is not a toy. Always
disconnect the charger before
wiping down and/or cleaning the
Razor Turbo Jetts Electric Heel
Wheels with a damp cloth.
The charger supplied with the Razor
Turbo Jetts Electric Heel Wheels
should be regularly examined for
damage to the cord, plug, enclosure
and other parts. In the event of
such damage, the Razor Turbo Jetts
Electric Heel Wheels must not be
charged until it has been repaired
or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Wall outlet - Green (stand by)
Wall outlet and product -
Red (charging)
Wall outlet and product -
Green (charged)
Note: Continue charging product
even if light turns green prior to
3 hours.
WARNING: Battery charge
can deplete over time. Periodically
recharge battery when not in use.
Your Razor Turbo Jetts Electric Heel Wheels may not have a fully charged battery; therefore you must charge the battery
prior to use. Be sure to charge the battery in a clean, dry location away from direct sunlight, flames or sparks.
• Initial charge time: 3 hours.
• Recharge time: up to 3 hours, even if the light
turns green. Recommended maximum charging time
is 24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended periods
of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the power button is turned OFF when
product is not in use. If the power button is left on for
an extended period of time, the battery may reach a
stage at which it will no longer hold a charge.
• Run time: Up to 30 minutes of continuous ride time.
Run time may vary depending on riding conditions, rider
weight, climate, and/or proper maintenance.
• Constant starting and stopping may shorten ride time.
• Battery life can vary depending on proper maintenance
and usage of the product.
• Do not charge at or below 32°F (0°C).
2 Note: Make sure power button
is in the OFF position. Plug the
charger into the charger port. The
light on the charger should turn
red during charging. The light on
charger will turn green again when
charging is complete.
1 Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
Charger
(Note: Charger design may vary from
one shown)

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
7
How to Stop
The Razor Turbo Jetts Electric Heel Wheels, like RipStiks or skateboards do not have conventional “brake”, however the
Razor Turbo Jetts Electric Heel Wheels stop by putting the ball of your feet to ground.
Note: Practice riding only in wide
open areas clear from curbs,
parking blocks and other obstacles.
Impacting the wheels against
any hard surface can damage the
wheels. Wheels are not covered
under the limited warranty.
USAGE
Note: Razor Turbo Jetts Electric
Heel Wheels must be moving
at least 3 mph (5 km/h), with
the drive wheel engaged with
the ground before the motor
will start.
Note: Motor will re-engage,
(without having to kick start), if
Razor Turbo Jetts Electric Heel
Wheels have not slowed down to
under 3 mph (5 km/h).
How to Ride
• Turbo Jetts are electric, motorized heel wheels that are controlled by
your foot when you ride them.
• The front heel wheel is motorized and pulls you along while the back
wheels just trail behind. Turbo Jetts are always used with one foot in
front of the other.
• The first thing to do is decide which foot will be in front. Most often it is
your stronger dominant foot that goes in front. If you skateboard or ride
a RipStik you already know this.
Stage 1- Balance Practice (POWER OFF):
• Practice gliding with the power OFF.
• Standing with the motorized foot in front of the other, point your front
toe up in the air pressing down on the back wheel. Make sure you feel
the back wheel touching the ground.
• Now try pushing off with your back foot and glide on the wheels
keeping the weight primarily over your front foot.
• Remember it’s important to keep one foot in front of the other for
stability. Try this on your own first or have a friend stand next to you if
you need a little help.
Stage 2- Give It A Try (POWER ON):
• Now that you’ve practiced balancing and gliding, switch the power ON.
• With the motorized foot in front of the other, point your front toe up and
push off with your back foot.
• Once you’ve started to glide the motor will automatically turn on and start to pull you.
• While keeping the weight primarily on your front foot, quickly get the back
foot behind the front and glide on the wheels.
Note: Release pressure from drive wheel to cut power to the motor then return to standing position.

4Replace cover, and reinstall four
(4) hex bolts, and tighten securely.
8
REPAIR AND MAINTENANCE
Before beginning repair or maintenance:
• Read the instructions
• Disconnect charger
• Turn the power button OFF and
Remove Battery
• Exercise caution around
exposed parts
• Contact Razor Customer Service
if unsure about any repair or
maintenance
Drive Wheel Replacement
Tool Required: 2.5 mm Allen Wrench
Wheel Replacement
Tool Required: 4 mm Allen Wrench
1-5 1-3
1-3
1-2
1-4
1-1
Wheel
1-1 Axle Bolt (X2)
1-2 Plastic Bushing Short (X2)
1-3 Bearing (X4)
1-4 Spacer (X2)
1-5 Plastic Bushing Long (x2)
1Remove the four (4) hex bolts
using 2.5 mm Allen wrench.
1Loosen axle bolt using 4 mm
Allen wrench.
2Remove cover and wheel.
3Replace new wheel.
2Pull axle bolt out and remove
wheel.
A
B
A
A
AA–Long
B–Short
B
B

3Insert battery.
9
Quick-Change Battery Replacement
REPAIR AND MAINTENANCE
1. Press the release button. 2. Pull battery out.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
10
Battery Care and Disposal
• To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section
on page 6 of this owner’s manual.
• Battery pack should not be disassembled, crushed, punctured, opened or otherwise mutilated.
Li-Ion
Disposal: Your Razor Turbo Jetts Electric Heel Wheels uses a lithium-ion battery pack which must be recycled or
disposed of in an environmentally safe manner. Do not dispose of a battery pack in a fire. The battery pack may explode
or leak.
Do not dispose of a battery pack in your regular household trash. The incineration, land filling or mixing of batteries
with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state approved
lithium-ion battery recycler.
Cleaning
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents, as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners, as they may damage or dissolve the plastic
components or soften the decals.
Charger
The charger supplied with the Razor Turbo Jetts Electric Heel Wheels should be regularly examined for damage to the
cord, plug, enclosure and other parts and in the event of such damage, the product must not be charged until it has
been repaired or replaced.
Use ONLY with the recommended charger.
Wheels and Bearings
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear and replace drive wheel as required. Under normal circumstances and conditions, Razor
wheels and wheel bearings are maintenance free. Nonetheless, it is the responsibility of the owner or guardian to
periodically inspect the wheels for wear and tear, the axle for proper tightness, bearings for side-to-side play, and for
loose parts. When a wheel develops play, this is an indication of excess wear and replacement is necessary. Replace
immediately with only genuine Razor wheels. Worn wheels/bearings are considered normal wear-and-tear and are not
covered by the Razor Warranty. Wheels other than genuine Razor wheels may not be compatible with your Turbo Jetts
Electric Heel Wheels. The use of anything other than genuine Razor replacement parts may affect your safety and will
void your warranty.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners. For the
complete selection of replacement parts visit shop.razor.com.
Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed on the back of this manual.
CONTAINS LITHIUM-ION BATTERY PACK. BATTERIES MUST BE RECYCLED.
UL 2271 COMPLIANT
Recycling Lithium-ion Batteries:
Lithium-ion batteries are recyclable.
You can help preserve our
environment by returning your
used rechargeable batteries to the
collection and recycling location
nearest you.
For more information regarding
recycling of rechargeable batteries,
call toll free 1-800-822-8837,
or visit http://www.call2recycle.org
Caution: Do not handle damaged
lithium-ion batteries.
REPAIR AND MAINTENANCE

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
11
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Does not work out of the box Product must be traveling at least
3 mph (5 km/h) before motor will engage
Razor Turbo Jetts Electric Heel Wheels must be moving at least
3 mph (5 km/h) with the drive wheel engaged with the
ground before the motor will start.
No longer works No lights on charger
Undercharged battery
Check power to wall outlet and/or try a different outlet.
Check lights on charger:
Plugged into wall - Green
Plugged into wall & unit - Red (charging)
Plugged into wall & unit - Green (charging complete)
No lights/Blinking lights - Replace Charger
Short run time/runs slow Rider’s weight
Riding conditions
Battery not fully charged
Old/damaged battery
Do not exceed 176 lb (80 kg) maximum weight limit.
Use only on flat, dry surfaces. Avoid inclines and areas with
heavy debris.
Charge product - refer to page 6 for charging information.
Replace battery.
Charge battery at least once a month when not in use.
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free [phone] to speak to a live Customer Service Representative.
*Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting.
NOTE: All troubleshooting steps should be performed by an adult only.

1-5 1-3 1 1-4 1-3 1-2 1-1
1-1 1-2 1-3 1-4 1
2
1-3 1-5
12
RAZOR TURBO JETTS ELECTRIC HEEL WHEELS PARTS
1. Wheels (X2)
1-1. Axle Bolt (X2)
1-2. Plastic Bushing (Short) (X2)
1-3. Bearing (X4)
1-4. Spacer (X2)
1-5. Plastic Bushing (Long) (x2)
2. Strap
Keep your Razor Turbo Jetts Electric Heel Wheels running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part
availability. (Specifications subject to change without notice.)
Non-Motorized Frame

1-4 1-3 1
2
1-4 1-3 1-2 1-1
1-1 1-2 1-3 1 1-4 1-3 1-5 3
4
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
13
RAZOR TURBO JETTS ELECTRIC HEEL WHEELS PARTS
1. Wheels (X2)
1-1 Axle Bolt (X2)
1-2 Plastic Bushing (Short) (X2)
1-3 Bearing (X4)
1-4 Spacer (X2)
1-5 Plastic Bushing (Long) (x2)
2. Battery
3. Drive Wheel
4. Strap
Keep your Razor Turbo Jetts Electric Heel Wheels running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part
availability. (Specifications subject to change without notice.)
Motorized Frame

NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACTYOUR INSURANCE COMPANY OR AGENT.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
AMERICAS
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
[email protected]
EUROPE, MIDDLE EAST, AFRICA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
[phone]
[email protected]
ASIA
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
[e-mail]
DISTRIBUTED IN THE UK AND IRELAND BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
[phone] Tel
[phone] Fax
[email protected]
DISTRIBUTED IN AUSTRALIA BY:
Funtastic Limited
2/307 Ferntree Gully Road,
Mount Waverley Vic 3149,
Australia
[phone]
[email protected]
Printed in China for Razor USA LLC.
Copyright © 2003-2017 Razor USA, LLC. All rights reserved. Razor®and the Razor logo design are among the registered trademarks of Razor USA LLC in the United States and/or select foreign
countries. Razor Turbo Jetts Electric Heel Wheels logo design are trademarks of Razor USA LLC.
US_171117
1515
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this product not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited Warranty
does not cover normal wear and tear, wheel, or any damage, failure or loss
caused by improper assembly, maintenance, storage or use of the
Razor Turbo Jetts Electric Heel Wheels.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION