RC-PRO PRO20-GPS User manual

Always y your drone safely and legally. Learn the rules and
regulations in your airspace and always follow them.
PRO20-GPS
GPS FPV CAMERA DRONE WITH GIMBAL
AND PRECISE HOVERING

Thank you for purchasing the PRO20-GPS Drone. Please read all
instructions and warnings carefully before operating. Please also keep this
instruction manual for future reference and maintenance.
IMPORTANT:
1. This drone is not a toy. It may cause injury or damage if not used properly
under a controlled environment. Always make sure you practice ying this
drone in an open airspace area while following the rules and regulations
which applies to the area to avoid any potential damage or Injury.
2. This product is suitable for experienced UAV pilots no less than 14 years of
age.
SAFETY PRECAUTIONS:
1. Keep it far away from any structures or crowds.
This R/C drone may vary slightly in speed or sensitivity while ying and can
cause potential danger. Therefore, please keep it far away from crowds,
buildings, trees, structures, high-voltage wire, etc. Please also avoid ying in
adverse weather conditions such as rain, electrical storms, and high winds
to ensure safety of the user, any spectators, and surrounding property.
2. Keep it away from any moist environment.
The inside of the drone is composed of many precision electronic and
mechanical parts. Therefore, please try to avoid any moisture or water content
from entering the main body of the drone as it may cause a breakdown of
the mechanical and electronic parts and thus cause an accident.
3. Only operate with included parts for intended use.
Always use original parts made and authorized by RC-PRO for replacements
and maintenance to insure ight safety.
DO NOT use for any illegal purpose or use beyond the scope of which your local
laws and regulations have stipulated.
4. Do not operate under the inuence of drugs or alcohol.
Please operate this R/C drone according to your own state and ying skill.
Any fatigue, bad mental state, or incorrect operation may increase the
probability of accidental risk.
5. Store it in a cool, dry place.
The R/C aircraft is composed of material such as metal, ber, plastic,
electronics, etc. Therefore, please keep it away from any heat source and
avoid prolonged exposure to direct sunlight. Excessive heat exposure can
cause distortion and damage.
1
INTRODUCTION

WARNING
DO NOT operate drone in a crowded area. Unexpected conditions, technical
issues or improper assembly may cause unplanned manoeuvring, which can
cause serious injury and/or property damage. The operator of this product
accepts all responsibility for any damages caused by its misuse.
1. KEEP AWAY from people and obstacles including high-rise buildings, high
voltage wires, etc.
2. DO NOT store the drone in a damp environment. The drone's interior is
composed of delicate electronic components and mechanical parts, which
can be seriously damaged by moisture.
Please take serious care, as this type of damage may not be visible on the
outside, but can cause the product damage or act unpredictably once in use.
3. Always operate with safety in mind. DO NOT use this drone under the
inuence of drugs or alcohol, or in the case of fatigue, as improper
operation can cause serious injury and/or property damage.
4. KEEP AWAY from rotating parts once the drone is in motion. Propeller
blades can cause serious harm to people and property.
5. DO NOT store or operate in high heat, as electrical components can be
damaged.
6. Small parts are included with this product. Please place it beyond the reach
of the children to avoid a CHOKING HAZARD or parts being mistakenly
swallowed.
7. Only the original charger made from our factory can be used.
8. Charger is not a toy.
2
9. Engine will heat up. Please DO NOT touch it to avoid being burned or injured.
10. Mini USB 5V wall charger recommended for charging. DO NOT use any charger
stronger than 5V.
11. Always operate your drone within eye sight.
12. Never y over groups of people.
13. Never y over stadiums or sports events.
14. Always understand and comply with airspace rules and regulations.

WARNING: CHARGING OF THE DRONE BATTERY MUST BE SUPERVISED AT
ALL TIMES BY AN ADULT. UNPLUG THE BATTERY WHEN FULLY CHARGED.
DO NOT OVER-CHARGE THE BATTERY.
3
9. Engine will heat up. Please DO NOT touch it to avoid being burned or injured.
10. Mini USB 5V wall charger recommended for charging. DO NOT use any charger
stronger than 5V.
11. Always operate your drone within eye sight.
12. Never y over groups of people.
13. Never y over stadiums or sports events.
14. Always understand and comply with airspace rules and regulations.
WARNING: Product should only be used by adults and children 14 years and
older.Adult supervision required for children under 14 years of age.
Check all batteries before charging and before use. Do not use or charge damaged batteries. Do not
over-charge batteries. Keep batteries away from heat and flame. Lithium is highly reactive with water;
always keep batteries away from water and humid conditions. Keep out of reach of children and pets.
Product should not be used by persons under 14 years of age, and should be accompanied by an
adult until 18 years of age. Our company is not liable for any damages resulting from improper use or
handling of the product.
RECHARGEABLE BATTERY
Connect the drone battery to the charger. Plug the charger into a power outlet
and fully charge (about 60 mins). The remote also includes a rechargeable
battery. DO NOT LEAVE CHARGING BATTERY UNATTENDED. Battery may be
warm when charging is complete. Disconnect the charger from the outlet,
then the battery from the charger.
BATTERY PRECAUTIONS
• Non-rechargeable batteries cannot be recharged
• Do not dismantle or short circuit batteries
• Keep batteries away from heat and ame
• Charge rechargeable batteries under adult supervision
• Remove rechargeable battery from drone before charging and when not in use
• Remove battery before cleaning
• Regularly check all wires, plugs and batteries to ensure proper performance
and safety. In case of damage discontinue use until repair
Lithium Battery Safety Precautions
Our company is not liable for any damages incurred by the appropriate or
inappropriate use of this product.

Low Electricity High
4
1
1. HD Camera 2. Landing Gear
3. Blade 4. Motor 5. LED indicator
23
1. Battery power indicator
2. USB charging port
3. Battery switch
MAINTENANCE
1. Use a clean soft cloth to clean this product frequently.
2. Avoid heating or prolonged exposure to the sun.
3. Don’t put the product in water. It will damage electronic parts.
4. Please check the plug and other accessories at regular intervals. If there is
any damage, please stop using it immediately until it is repaired completely.
BATTERY OPERATION
Press the battery shortly to switch on, hold for 2 seconds to switch it o.
12
3
4
DRONE PARTS
Blade A
Blade A Blade B
Blade B
5

5
REMOTE CONTROL
BATTERY CHARGING INSTRUCTIONS
1. The included rechargeable battery can be charged while being
connected or disconnected for the drone. Plug the USB cable to the
battery and plug the other side to a power source and the battery will
recharge.
2. You can use car USB port or power banks to charge this battery.
3. Full charging time takes about 60 minutes, Flight time about 8 minutes.
4. The transmitter is equipped with a rechargeable lithium battery.
Charging time: Approx. 50 minutes Run time: Aprox. 3 hours
1
2
34
5
6
13
98
710
12
11
1. Throttle joystick.
2. Direction joystick.
3. Press for one button RETURN HOME;
press again to cancel Return Home.
4. ON / OFF.
5. One button take o with auto hover, one button
landing Hold 3 secs for Emergency stop.
6. USB charging port.
7. Speed+/Speed-.
8. Hold the button for 3 seconds, enter Trim mode.
Click the button, cancel Trim mode.
Note: No need to trim under the GPS mode.
9. Click once to toggle headless/normal mode.
Hold the button for 3 seconds to turn o GPS
mode.
10. Adjust the angle of camera: Spin button down:
camera down. Spin button up: camera up.
11. Click the button to take photo.
12. Click the button to take video; Click the button
again to cancel video mode.
13. Phone Holder.
14. Power.
15. Speed.
16. Video.
17. Return Home.
18. Charging.
19. Headless Mode.
21. Trim-See #8 above for access to trim mode.
14 15 16 17
18 19 20 21

6
CAUTIONS WHEN CHARGING:
1. When charging, please put this product in a dry ventilated area and keep
it far away from heat sources or ammable products.
2. When charging, it is recommended to remove the batteries from the drone.
Charging process should be supervised by an adult so as not to cause an
accident. The battery can also be charged while in the drone.
3. After ying, please do not charge the battery if the surface temperature is still
warm. If the battery has been used for a long time, or appears to be swollen,
please replace them.
4. Please make sure that you use the original USB charging cable provided.
5. A battery when not in use for a long time will lose its charge automatically.
Charging or discharging too often may reduce the life of the battery.
DISCLAIMER: You must use the original USB cable and standard 5V wall charger.
WARNING: Never charge with an input stronger than 5V. This can cause the
battery to overheat.
Please choose the spacious indoor or outside environment for ying, also it
requires that it should be ied under the weather of non- snow or non-storm
with wind force less than Level 4. When ying, please DO keep it far away from
the crowd, tree, electric wire, skyscraper, airport or signal transmitting tower, etc.
Step 1: Turn on drone and set down on a level surface*
— *The drone will auto-trim to this level surface.
— All lights blinking red.
PREPATATION FOR FLIGHT/GPS CALIBRATION

7
Front
Front
Step 2: Turn on remote
— Press Up, then Down on the left joystick.
— Lights ashing blue (back) and white (front).
— NOTE: *You can connect to the WiFi at this time to
view the current drone status on the RC-PRO GPS App,
or wait until after GPS is calibrated.
GPS CALIBRATION (CONTINUED)
Step 3: Reset to Factory Setting / Calibrate Gyroscope
— Press the Joysticks into the 11 & 1 o’clock positions.
— Lights rapid-blinking blue (back) and white (front).
— App Drone Status: “Gyroscope is being calibrated”
“Gyroscope okay”.
Step 4: Initiate GPS Compass Calibration
— Joysticks at the 1 & 11 o’clock positions.
— Lights rapid-alternate between blue/red (back) and
white/red (front).
— App Drone Status: “Compass calibration”.
Step 5: GPS Compass Calibration Part 1
— Keeping the drone level, pick up the drone from the
back and rotate your body in one full circle (360°).
— Back lights will turn to a solid blue.
Step 6: GPS Compass Calibration Part 2
— From the bottom, hold the drone face-down and rotate
the your body in one full circle(360°).
— Front lights will turn to a solid white.
— App Drone Status: “Compass calibration okay”.
Step 7: Finalize GPS Calibration
— Set drone back down to level surface.
— Lights return to rapid-blinking blue (back)
and white (front) — This means the drone
is finalizing its GPS calibration*.
— *This process can take a few minutes.
— App Drone Status: “Waiting for GPS signal”.
Once the lights have switched to all solid, you are ready to y!
— Blue (back) and white (front) lights are all solid (no blinking).
— App Drone Status: “Ready to y”.

8
KEY FEATURES
• Control Distance: Up to 200 meters
• Video Transmission Distance: Up to 60 meters
• Flight time: about 8 mins
• Quadcopter Battery: 3.7V 1000mAh Lithium-ion battery
• Remote Battery: 3.7V mAh Lithium-ion battery
1. Dual GPS positioning system
2. Precise overing
3. GPS one-key return 4. 2.4GHz Radio Control Technology
5. 9-Axis GYRO 6. colorful ashing lights
7. Headless Mode 8. Easily to replace the battery
9. Take photos and video by the transmitter
LOW VOLTAGE RETURN
CAUTION:
1. When there is insufficient power, the Drone will start Auto-Return. When
safe return is confirmed, please DO NOT operate the transmitter any more.
If it is not safe, you can push the throttle lever to raise the ying height
and control the steering direction of the Quadcopter so as to y it to the
appropriate area for landing.
2. Always make sure the drone has a clear landing approach and surface in
order to avoid injury or damage.
1. Always avoid objects such as trees, buildings etc. which might interrupt in
your ight path. Keep Your drone within eye sight and stay away from
people, animal and objects.
2. Always be alert and ready to “emergency stop” in case of need.
3. Always stand in a clear open area when initiating the “Return home”
function.
* WARNING: This drone is NOT equipped wth obstacleavoidance.
BE AWARE OF YOUR SORROUNDSINGS WHILE FLYING

9
PRECISE HOVERING
This drone is equipped with GPS which enable it to hover in a position
precisely. Accuracy will uctuate according to the GPS signal in the ight
area.
1. Complete the GPS calibration process and have the drone at
“ready to y” status.
2. Press the One-key Take-o button.
3. Choose a spot in the sky and the drone will remain in that spot.
4. Adjust the height of this spot using the right control stick.
Trimming is manual adjustment of the drone’s ight angles. It should only
be used when the drone is drifting instead of hovering in a secure space
with no wind. Please follow these instructions in order to trim your drone:
Hold #8 the trim button for 3 seconds into trim mode,
#21 indicador ashing.
1. If the drone oats forwards, the operator shall pull
the right lever backwards to adjust.
2. If the drone oats backward, the operator shall pull
the right lever forwards to adjust.
3. If the drone oats leftward, the operator shall pull
the right lever rightwards to adjust.
4. If the drone deviates rightward, the operator shall
pull the right lever leftwards to adjust.
The trimming can be made repeatedly till it ies steadily.
Then press #8 the trim button to exit, and #21 indicator
turns o.
Note: No need to trim under the GPS mode.
TRIMMING INSTRUCTIONS
8
21

10
Please put the drone in a forward-facing position. After syncing, but
before take-o, press the Headless Mode button on the remote control
and to enter Head-less Mode. Press it once again to exit Headless Mode.
HEADLESS MODE
OPERATING INSTRUCTIONS
Push the left lever (accelerator) up and
down, The drone will ascends and
descends accordingly.
Ascend
Descend
Push the left lever (accelerator) leftward
and rightward,the drone will turn left
and turn right accordingly.
Left turn
Right turn
Push the right lever (swerving rudder),
the drone will go forward and
backward accordingly.
Fowards
Backwards
Push the right lever (swerving rudder)
leftward and rightward, the drone
will go leftward and rightward accordingly.
Left
sideward fly Right sideward fly

Waiting for GPS Signal D:00 H: 0.0 DS: 0.0 VS: 0.0
11
- Connect the power of this drone, and then access into “SETTING”
in the mobile phone, open the “WIFI” and nd the “RC-PRO GPS”.
When the link is successfully connected, please exit the“Setting”option.
- Open “RC-PRO GPS” APP in the mobile to access into the control
interface.
QR code of “RC-PRO GPS”
APP for Apple IOS system
(Please scan this QR code to
install this software).
QR code of “RC-PRO GPS”
APP for Android system
(Please scan this QR code to
install this software).
SOFTWARE DOWNLOAD AND INSTALLATION
APP INTRODUCTION
Wait until the Drone Status says “Ready to Fly” before initiating ight.
This will ensure that your GPS is synced and your drone is ready to
y.

12
Waiting for GPS Signal D:00 H: 0.0 DS: 0.0 VS: 0.0
Return Home
Auto Takeo
Auto Land
Take Photo
Recording
Take Video
Back to Main Menu
Controls ON/OFF
Flight Setting
Drone Battery
Flip Screen VR Split Screen
Remote BatteryFlight Record
GPS Signal Indicator
Media Gallery(Share)Drone Status Distance (meters)
Height (meters)
Speed(meters/sec)
Headless Mode

13
Insert the optional memory card (not included) into the webcam module’s card
channel which is on the bottom of the drone, connect the drone’s power, and
sync drone and remote control. The blue indication light on the webcam
module will turn solid, and the camera is ready for photos and videos.
(Memory card available separately)
CAMERA CONFIGURATION
When you press the power button on the remote control, the red light will
ash once, that means the drone is taking photo. When you press the video
button, the red light turns into constant on, that means the drone is taking
video. Press the video button again to stop video.
NOTE: When using the RC-PRO GPS app, photos and videos will
automatically be saved to your smartphone.
If you are using an memory card, photos and videos will automatically be
saved directly to the card.
PICTURE & VIDEO RECORDING

14
TROUBLESHOOTING
PARTS LIST (Included)
Drone’s lights are ashing
and no response from the
drone.
The blades spin but the
drone does not take o.
1. The blades are not
placed properly.
2. The blades are damaged.
1. Transmitter is not paired
to the drone.
2. No battery power.
1. Follow the pairing process.
2. Charge the battery.
1. Make sure your blades are
placed properly according
to page 4.
2. Replace the blades
Blade A/B X2
Screwdriver X1
Blade Cap X2
USB Cable X1
Only for charging
Landing Gear
X2
PROBLEM REASON SOLUTIONS
Tripod Wrench X1
The drone shakes
uncontrollably.
Drone does not hover
accurately.
Drone does not achieve
“Ready to y”. No/Weak GPS reception.
1. Wait a few minutes for
GPS reception.
2. Stay away from reception
blocking structures.
1. The blades are damaged.
2. One of the motors is not
spinning in accurate speed.
3. The gyroscope is out of
balance.
4. The drone needs trimming.
1. Replace the blades
2. Replace the motor.
3. Calibrate the gyroscope
(Page 7 step 3).
4. Follow trimming instructions.
The blades are damaged. Replace the blades
AB
We believe that you should make the most out of your drone.
If you are ever in need of advice, service or parts please visit our website
for a list of our retailers.
WWW.RCPRO.CA