RC4WD Gelande II User manual

1
Recommended Tools
Hex Drivers (1.5mm, 2mm, 2.5mm)
Cross Wrench (M2,M3,M4) Side Cutter
Modeling/Craft Knife
Thread Lock Long Nose Pliers
Tips for Assembly
Use good quality hex drivers to avoid stripping screw heads.
Use thread lock when putting metal screws into metal parts.
Use thread lock sparingly.
Do not over tighten screws otherwise you may strip the thread.
Plastic Cement/Glue
(Non-Whitening CA Glue)

2
RC4WD Limited Warranty
All RC4WD products are warranted to be free of defects in
materials and workmanship when new. Our limited warranty does
not cover damages due to normal wear and tear, user error of
assembly or installation, user modifications, user's failure to
perform routine maintenance, addition of aftermarket parts or option
parts. This warranty lasts as long as the original purchaser owns the
product.In the event of a defect under this warranty, RC4WD will, at
our discretion, replace the product, provided our inspection indicates
that an original defect exists. RC4WD reserves the right to replace
any product which is no longer available with a product of
comparable value and function. If RC4WD determines the repair is
not covered under warranty guidelines, we will contact you to
discuss your options. If you have any questions, please contact us
via email at [email protected].

1. ESC with BEC (Z-E0007)
Electronic Manual
This is a step by step overview of your new Gelande II RTR electrical items and how they connect.
2. ESC connected to the Brushed 45T Crawler Motor (Z-E0004)
3

3.
4.
4
This connects the BEC of the ESC to the radio’s receiver (Z-R0008). This connects to the B/C port.
Connecting the BEC to the radio’s receiver Channel (B/C). Connecting the ESC to the radio’s receiver
Channel 2 (CH2). Channel 2 is the throttle control of the radio.

5.
6. Show the battery connected to the ESC. 4-9 NiMH cells (1.2V per cell) or 3S 11.1V LiPo.
5
Connect the servo (Z-E0035) to the radio’s receiver Channel 1 (CH1). This controls the trucks steering
from the radio.

6
Note: Battery is not included.
7. This final step shows all the items as they are connected on the truck.

7
T
C
(1) Remove the battery compartment cover
(2) Install 4 "AA" batteries and replace
compartment cover
RC4WD
Please replace batteries when
the power indicator blinks or
the buzzer beeps

8
Electrical Powered Model
Binding the Transmitter and Receiver
Brake/Speed Down
Forward/Speed Up
Turn on the transmitter
3. When the LED on the
receiver becomes solid,
the binding process is
complete.
Turn on the receiver power.
Press the SW switch. The
receiver's LED should start
Flashing.
2.
1.
Fail Safe Function Setting
Gas Powered Model
Receiver and Servo Connection

9
Countersunk Flat Spacers
Set Screws
M3x15 14X
M3 Drive Shaft Screw Pin 4X
Nuts
Z-S0648
Z-S0649
Z-S0860
Z-S0746
Z-S0809
Z-S0600
Z-S0806
Z-S0821
Z-S0125
Z-S0308
Z-S0650
Z-S0804
Z-S0303
Z-S0629
Z-S1265
2mm 2X
3mm 4X
5mm 1X
M3 5X
M4 4X
M2.5 20X
M3x6 2X
M3x8 7X
M3x10 4X
M3x14 6X
M3x5 2X
M3x10 6X
1mm 2X
Head Screws