RCI F2164 User manual

INSTALLATIONSINSTALLATIONS Fail Locked F2164 (Fire-Rated)
& Fail Unlocked 2364
ELECTRIC STRIKE
Standard Parts:
Insert
Deadbolt Keeper
Deadbolt Plug
Deadlatch Ramp (Auxiliary Bolt Bracket)
Keeper Sliding Shims: 1/16" (1.5mm) and 1/8" (3.0mm)
A Centerline Latch Faceplate and an Offset Latch Faceplate are provided.
Both are: 4-7/8" x 1-1/4" (123.8mm x 31.8mm)
Trim Plate
12VDC or 12 to 24VAC Cable Connector
24VDC Cable Connector
Anti-Tamper Security Screws (2x 12-24) and Bit
Mounting Tab Kit (2x tabs, 4x shims and 5x 12-24 screws)
Inductive Kickback Suppressor - MOV
Wiring Instructions
Use the appropriate wire harness supplied.
12V for 12VDC & 12-24VAC
24V for 24VDC only
Attach the red wire to (+) positive of the power supply.
Attach the black wire to the (–) negative of the power supply.
If using AC power, polarity is not observed.
To meet BHMA A156.31, install the MOV provided across the
positive and negative wires or terminals of the harness. The MOV
is not polarity sensitive.
NOTE: If a suppression diode is required for access control,
observe proper polarity.
Latch Monitor Wires
Black = Common (C)
Blue = Normally Closed (NC)
Orange = Normally Open (NO)
Red Black
+-
+-
Red Black
24VDC
Terminal
12VDC
12-24VAC
Terminal
NO
NC
C
Latch
Monitor
Optional LM
Wiring the 2 Series Electric Strike
*Warning: The fire and security ratings shown on the strike labels no longer apply with the use of this faceplate.
The F2164 fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction and shall
not impair the operation of the panic hardware or intended operation of the emergency exit.
These strikes must be connected to a compatible UL Listed Burglary or Access Control Power Supply.
PCN15058
R06/16GR
© 2016 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY
WWW.RUTHERFORDCONTROLS.COM • PHONE: [phone] • FAX: [phone] • E-MAIL: [email protected]
ISF2
Accessories:
Latch Monitor Switch : F2LM
9" Centerline Latch Entry Faceplate : F2-19*
9" Offset Latch Entry Faceplate : F2-29*
Filler Plate - 2 Series Strike : 2FP
UL 294 Performance Ratings:
Access Control Line Security : Level I
Destructive Attack : Level I
Endurance : Level IV
Standby Power : Level I

2
Fail Locked F2164 (Fire-Rated) & Fail Unlocked 2364 Installation Instructions (Continued)
1.Mount the strike into the frame without the faceplate. Tighten
the mounting screws just enough to hold the strike in place;
you may need to slide it up-down for adjustment.
Adjust Deadbolt Keeper:
First, extend the deadbolt and move the door so that deadbolt
touches the keeper.
Mark deadbolt limit lines on strike keeper.
Then, open the door and retract the deadbolt. Adjust the
deadbolt keeper position so that it aligns with deadbolt limit
lines marked on keeper. Move the strike up-down if needed.
Adjust Deadlatch Ramp:
First, move the door towards the strike so that the deadlatch
touches the keeper.
Mark deadlatch limit lines on keeper.
Then, open the door. Adjust the deadlatch ramp so that it
aligns with deadlatch limit lines marked on keeper.
© 2016 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY
WWW.RUTHERFORDCONTROLS.COM • PHONE: [phone] • FAX: [phone] • E-MAIL: [email protected]

3
Fail Locked F2164 (Fire-Rated) & Fail Unlocked 2364 Installation Instructions (Continued)
Adjust Plug-in Latch Monitor (Accessory):
First, move the door towards the strike so that the latch
touches the keeper.
Mark latch limit lines on keeper.
Then, open the door. Mount the Latch Monitor on
the strike housing so that it is between the latch limit
lines marked on keeper.
2. Mark strike position on the frame.
3. Peel the adhesive backing from tape on the back side of
the appropriate faceplate. Remove the strike mounting
screws. Hold the strike in position as marked on frame.
Carefully position the faceplate onto the strike and secure
to the frame.
© 2016 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY
WWW.RUTHERFORDCONTROLS.COM • PHONE: [phone] • FAX: [phone] • E-MAIL: [email protected]

4
Fail Locked F2164 (Fire-Rated) & Fail Unlocked 2364 Installation Instructions (Continued)
Trim Plate: This can be used in case the frame cutout is bigger
than required.
Bend tabs to grip frame
Deadbolt Plug: If the lock set doesn’t have a deadbolt,
then replace deadbolt keeper with deadbolt plug.
NOTE: Deadlatch Ramp also acts as a Keeper stop, so don’t
forget to insert it for centerline cylindrical lock applications.
Deadbolt
Plug
Cylindrical
Horizontal Adjustment: If there is play in the door when closed;
the keeper shims may be used to minimize play.
Keeper Sliding Shim
© 2016 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY
WWW.RUTHERFORDCONTROLS.COM • PHONE: [phone] • FAX: [phone] • E-MAIL: [email protected]