Recordex Clarity User manual

CLARITY ELECTRIC PROJECTOR SCREEN
THANK YOU FOR CHOOSING OUR PROJECTION SCREEN.
PLEASE READ THE MANUAL BEFORE USING.
110V 220V NEW

THE SHAPE OF SCREEN
SPARE PARTS LIST FOR MOTORIZED SCREEN
NO.1
HAND SET
REMOTE
CONTROL BOX
PLUG
SWITCH BOX
PLUG
Thank you for choosing our screen.
Read this manual carefully to ensure proper usage,you may also find
the solution if you have problems.
IMPORTANT ATTENTION the installation of the screen,the
electric connections,the setting of the limit switches,must be made
from trained engineer only.
A
01-03
01-02 01-07 01-01
01-06
01-04
01-05 02-01
02-02
02-03
02-05
02-04
02-06
02-07
02-08
B

MICRO SWITCH
LIMIT SWITCH
MICRO SWITCH COVER
CONTACT CHIP SETTING
CONTACT CHIP 1
CONTACT CHIP 2
LOCATING SHAFT OF
CONTACT CHIP
01-01
01-02
01-03
01-04
01-05
01-06
01-07
ROLLER ROTOR
ENDCAP
SWING ARM 2
SOLID AXLE 2
SWING ARM 1
SOLID AXLE 1
SWING ARM AXES
TORSIONAL SPRING
02-01
02-02
02-03
02-04
02-05
02-06
02-07
02-08
LEFT END CAP
SCREEN HOUSING
RIGHT END CAP
BEARING
ROLLER END CAP
ROLLER
MOTOR HOLDER
SYNCHRONOUS MOTOR
LATCH
CONNECTION
ABSORBER COVER
SCREEN FABRIC
PULL BAR
RUBBER END CAP
SLAT BAR BLOCK
LOCK PIECE
ADJUSTMENT COVER
RING
CORD FASTENER
00-01
00-02
00-03
00-04
00-05
00-06
00-07
00-08
00-09
00-10
00-11
00-12
00-13
00-14
00-15
00-16
00-17
00-18
00-19
NO.2
00-01 00-02
00-03
00-04
00-05
00-06 00-08
00-09
00-07
00-10
00-11
00-17
00-18
00-19
00-12
00-15
00-16 00-13
00-14
B
A

INSTALLATION NOTE
Must be installed from direct sunlight.
Proper ventilation place.
Proper dampness.
Clear place.
Avoid violent jarring.
Avoid the direct air current from air-condition,heater etc.Do not
expose the screen in the High or Low temperatme condition.
Unpack the screen carefully, be sure the screen is in good
condition, check all the accessories are packed inside the carton.
Check the voltage and frequency marked on the screen is in
accordance with the local power supply. It is suggested only to use
the screens indoor under normal temperature and humidity.
Refer the fig below to fix the screen to the wall or to the ceiling.
VOLTAGE AND FREQUENCY
Choose the voltage acoording to the local requirement:110V/60Hz or
220V/50Hz.
INSTALLATION INSTRUCTION
NO.3
FIX THE SCREEN TO THE WALL FIX THE SCREEN TO THE CEILING

L
PLUG
WHITE
WHITE
RED
BLACK
RED
BLACK
BLACK
RED
BLACK
M
YELLOW/GREEN
GREEN UP
L2
C
CAP
DOWN
G
NMICRO SWITCH
MICRO SWITCH
AC 110V/60Hz
AC 110V/60Hz
TERMINAL BLOCK
MOTOR
REMOTE CONTROLLER
NO.6
TECHNICAL DATA FOR FABRIC
Matte White Screen
Gain: 0.9
Viewing Angle: >160°
High color rendering, high resolution.
Glass Beaded Screen
Gain: 2.2
Viewing Angle: >30°
High color rendering, high resolution.
HOW TO MEASURE THE TECHNICAL DATA OF REFLEX SCREEN
Gain Measurement: refer the fig below
Standard: JB/T8389 issued by Ministry of Machinery Industry
5°
PROJECTOR
Height
Direction
LUMINOUS METER
SCREEN
STANDARD BOARD

NO.7
45°
35°
25°
15° 5° 5° 15°
25°
35°
45°
PROJECTOR
LUMINOUS METER
SCREEN
Viewing Angle Measurement: refer the fig below
Standard: JB/T8389 issued by Ministry of Machinery Industry
White PVC
Black PVC
Base
Glass beaded
White PVC
Black PVC
Base
SCREEN FABRIC
MATTE WHITE SCREEN SURFACE GLASS BEADED SCREEN SURFACE