red lion RAM-6021 User manual

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 1
QUICK START GUIDE
RAM-6021
WIRED ROUTER
UNPACKING INSTRUCTIONS
1. Unpack the Red Lion unit and verify the following components are
enclosed for the RAM-6021 Router: RAM-6021 & this quick start
guide.
2. There are 2 methods to provide power to the router:
• 4-pin screw terminal
• Side mounted 2.5mm barrel connector
The router requires a power source between 8 and 30 VDC to
operate:
3. Connect to the WAN or LAN port for network connectivity.
ACCESSING THE WEB USER INTERFACE
1. Connect PC to the RAM-6021 Router
Connect a CAT-5 Ethernet cable between the local PC and the
unit’s Ethernet port. Verify that the green LED is lit.
2. Setup PC IP Address
PC to Ethernet Interfaces
Select “Use the following IP address” and fill in the blank fields
with the information below:
3. Access Web User Interface
Open a web browser and enter the following in the address bar:
•WAN/ETH0: http://192.168.0.1:10000/
•LAN/ETH1: http://192.168.1.1:10000/
LOGIN INSTRUCTIONS
•User Name: admin (lowercase letters)
•Password: last six digits of the unit’s serial number
Upon successfully logging in, the web UI will launch.
Note: For security purposes, it is recommended that the admin pass-
word be changed according to your internal policies.
To change password, go to: Admin->Access Settings.
Web UI:
You are now connected to the web interface. If you should see anything
other than the screen shown above, please refer to the RAM-6021 User
Manual, located on our website: www.redlion.net.
For more information to set up Modbus features, please refer to the
RAM-6021 User Manual.
HARDWARE STATUS LEDs
RED LION CONTROLS TECHNICAL SUPPORT
If you have followed all of the instructions up to this point, are satisfied
that you are not having an authentication problem and your unit is still
not communicating, then it it is time to contact Red Lion Technical Sup-
port at [email protected] or 1-877-432-9908.
LABEL DESCRIPTION
GND Ground
PWR+ Power 8 to 30 VDC (12 or 24 VDC nominal)
IN Digital and analog input
OUT Digital output
For assistance with configuring your PC, see the appropri-
ate Microsoft support webpage listed at:
http://support.microsoft.com
WAN/ETH0 LAN/ETH1
IP Address 192.168.0.2 192.168.1.2
Subnet Mask 255.255.255.0 255.255.255.0
Default Gateway 192.168.0.1 192.168.1.1
Preferred DNS 192.168.0.1 192.168.1.1
LED State Description
Power ON Power is applied to the router
WView section 1.1.7 in Hardware Guide
RS232
ON Link established with serial device but
no data activity
FLASH Data transmitted/received with
attached serial device
Ethernet ON Link established with Ethernet device

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 2
Quick Start Guide
INSTALLATION AND HAZARDOUS AREA WARNINGS
All power, input and output I/O wiring must be in accordance with Class
I, Division 2 wiring methods are in accordance with the authority having
jurisdiction. This equipment is suitable for Use in Class 1, Division 2,
Groups A, B, C and D or Non-Hazardous Locations Only.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO
BE NON-HAZARDOUS.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS
MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
WARNING - EXPLOSION HAZARD - BATTERIES MUST ONLY BE
CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.
WARNING - EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEAL-
ING PROPERTIES OF MATERIALS USED IN THE RELAYS.
AVERTISSEMENTS POUR INSTALLATION ET
ENDROITS DANGEREUX
Tout pouvoir, le câblage d'entrée et de sortie (I/O) doivent être con-
formes aux méthodes de câblage de Classe I, Division 2 et conformé-
ment à l'autorité compétente. Cet équipement est adapté pour une
utilisation en Classe1, Division 2, Groupes A, B, C et D ou endroits non-
dangereux seulement
AVERTISSEMENT - RISQUE D'AVERTISSEMENT - NE DÉBRANCHEZ PAS
L'ÉQUIPEMENT PENDANT QUE LE CIRCUIT EST DIRECT OU À MOINS
QUE L'ENVIRONNEMENT SOIT CONNU POUR ÊTRE NON-DANGEREUX.
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE TOUT
COMPOSANT PEUT NUIRE À LA CONFORMITÉ DE CLASSE I, DIVISION 2.
AVERTISSEMENT - RISQUE D'EXPLOSION - LES BATTERIES DOIVENT
SEULEMENT ÊTRE REMPLACÉES DANS UNE ZONE RECONNUE COMME
ÉTANT NON-DANGEREUSE.
AVERTISSEMENT - L'EXPOSITION À CERTAINS PRODUITS CHIMIQUES
PEUT DÉGRADER LES PROPRIÉTÉS D'ÉTANCHÉITÉ DES MATÉRIAUX UTIL-
ISÉS DANS LES RELAIS ÉTANCHE PÉRIPHÉRIQUE.