red lion NT24k Series User manual
N-Tron®Series
NT24k®Modular Series
Managed Gigabit Ethernet Switches
Hardware Manual | July 2017
COPYRIGHT
©2015-2017 Red Lion Controls, Inc. All rights reserved. Red Lion, the Red Lion logo, N-Tron, and NT24k
are registered trademarks of Red Lion Controls, Inc. All other company and product names are trademarks
of their respective owners.
Red Lion Controls, Inc.
20 Willow Springs Circle
York, PA 17406
CONTACTINFORMATION:
Inside US: +1 (877) 432-9908
Outside US: +1 (717) 767-6511
Website: www.redlion.net
Email: [email protected]
N-Tron® Series NT24k® Modular Hardware Manual i
REVISED 2017-07-01 TABLE OF CONTENTS
DRAWING NO. LP0982-B
Table of Contents
Preface..............................................................................................iii
Disclaimer .........................................................................................iii
ComplianceInformation ...........................................................................iii
FCCStatement....................................................................................iii
DéclarationdeconformitéFCC .......................................................................iii
IndustryCanada/IndustrieCanada ...................................................................iv
EnvironmentalImpactStatement.....................................................................iv
ToxicEmissions ....................................................................................iv
TrademarkandRegistrationAcknowledgments ....................................................iv
ReleaseNotesandDocumentUpdates.............................................................iv
PublicationHistory.................................................................................iv
RelatedDocuments.................................................................................v
DocumentComments...............................................................................v
AdditionalProductInformation .....................................................................v
CautionsandWarnings/MisesenGardeetAvertissements ........................................v
GeneralSafetyCautionsandWarnings/PrécautionsetAvertissementsdeSécuritéGénérale....................v
ElectricalSafetyWarnings/AvertissementsdeSécuritéélectrique.........................................vi
EnvironmentalSafetyCautionsandWarnings/SécuritéEnvironnementaleMisesenGardeetAvertissements.....vii
HazardousLocationWarnings/LesAvertissementsd'EmplacementDangereux ..............................vii
SurroundingAirTemperature/TemperatureAmbiante..................................................viii
LaserSafetyWarnings/AvertissementsdeSécuritéLaser ...............................................viii
RegulatoryInformation ............................................................................ix
ProductSafety ....................................................................................ix
Emissions ........................................................................................ix
Immunity ........................................................................................ix
Other ........................................................................................ix
Chapter1 ProductOverview.................................................................1‐1
1.1 NT24k®ModularSeriesCommonFeatures................................................1‐1
1.1.1Connectivity.............................................................................1‐1
1.1.2Performance ............................................................................1‐1
1.1.3Environmental ...........................................................................1‐1
1.1.4Monitoring..............................................................................1‐1
1.1.5Security ................................................................................1‐1
1.1.6AvailableBaseModels....................................................................1‐2
1.2 NT24kRackmount ........................................................................1‐3
1.2.1FeaturesandBenefits .....................................................................1‐3
1.2.2NT24KRackmountSpecifications ...........................................................1‐4
1.2.3NT24KRackmountDimensions.............................................................1‐5
1.3 NT24k‐DR16 ..............................................................................1‐6
1.3.1FeaturesandBenefits .....................................................................1‐6
1.3.2NT24k‐DR16Specifications ................................................................1‐7
1.3.3NT24k‐DR16Dimensions ..................................................................1‐8
1.4 NT24k‐DR24 ..............................................................................1‐9
1.4.1FeaturesandBenefits .....................................................................1‐9
1.4.2NT24k‐DR24Specifications ...............................................................1‐10
TABLE OF CONTENTS REVISED 2017-07-01
DRAWING NO. LP0982-B
ii N-Tron® Series NT24k® Modular Hardware Manual
1.4.3NT24k‐DR24Dimensions .................................................................1‐11
1.5 NT24kViews.............................................................................1‐12
1.5.1NT24kRackmountUnitFrontView .........................................................1‐12
1.5.2NT24kRackmountUnitView(ModuleSlotsIdentified) ........................................1‐12
1.5.3NT24k‐DR16FrontView ..................................................................1‐12
1.5.4NT24kDRUnitView(ModuleSlotsIdentified)................................................1‐13
1.6 LEDs.....................................................................................1‐14
1.6.1EIPIndicators...........................................................................1‐14
1.7 TransceiverCharacteristics ...............................................................1‐15
1.7.1NT24k‐FX8Module‐100MBFiberTransceiverCharacteristics..................................1‐15
1.7.2NT24k‐GX8Module‐GigabitFiberTransceiverCharacteristics..................................1‐15
1.7.3NT24k‐SFP‐DM8Module‐SFP100BaseFiberTransceiverCharacteristics .........................1‐15
1.7.4NT24k‐SFP‐DM8orNT24k‐SFP8Modules‐SFPGigabitFiberTransceiverCharacteristics .............1‐15
1.8 OrderingGuide ..........................................................................1‐16
1.8.1NT24KRackmount ......................................................................1‐16
1.8.2NT24K‐DR16 ...........................................................................1‐16
1.8.3NT24K‐DR24 ...........................................................................1‐17
1.8.4PortModules...........................................................................1‐17
1.8.5SFPTransceivers ........................................................................1‐18
Chapter2 HardwareInstallation............................................................ 2‐19
2.1 Unpacking ...............................................................................2‐19
2.2 ModuleInstallation......................................................................2‐19
2.3 MountingtheNT24k .....................................................................2‐20
2.3.1RackmountInstallationInstructions........................................................2‐20
2.3.2DINRailMountingInstructions............................................................2‐20
2.3.3DIN‐RailRemovalInstructions .............................................................2‐21
2.4 PowerSource ............................................................................2‐22
2.4.1NT24kRackMountwithDCPowerInputInstalled ............................................2‐22
2.4.2NT24kwithACPowerSupplyInstalled......................................................2‐23
2.5 GroundingtheUnit ......................................................................2‐24
2.6 ConfigurableAlarmContact ..............................................................2‐25
2.7 ConnectingtheUnit......................................................................2‐26
2.8 EthernetCable ...........................................................................2‐27
2.9 NTCD ....................................................................................2‐28
2.10 USBInterface............................................................................2‐29
2.10.1USBCable .............................................................................2‐29
2.10.2Termi na l ...............................................................................2‐29
2.11 Cleaning.................................................................................2‐30
Chapter3 AccessingtheWebSoftwareInterface........................................ 3‐31
ServiceandSupportInformation................................................................... 3‐33
LimitedWarranty ................................................................................... 3‐34
N-Tron®Series NT24k®Modular Hardware Manual iii
PREFACE REVISED 2017-07-01
DISCLAIMER DRAWING NO. LP0982-B
Preface
Disclaimer
Portions of this document are intended solely as an outline of methodologies to be followed during the
maintenance and operation of N-Tron®Series NT24k®Modular equipment. It is not intended as a step-by-step
guide or a complete set of all procedures necessary and sufficient to complete all operations.
While every effort has been made to ensure that this document is complete and accurate at the time of release, the
information that it contains is subject to change. Red Lion Controls is not responsible for any additions to or
alterations of the original document. Industrial networks vary widely in their configurations, topologies, and traffic
conditions. This document is intended as a general guide only. It has not been tested for all possible applications,
and it may not be complete or accurate for some situations.
Users of this document are urged to heed warnings and cautions summarized at the front of the document, such as
electrical hazard warnings.
ComplianceInformation
It is recommended that the owner of this equipment determine and ensure conformance with any specific and
applicable local regulations.
FCCStatement
This product complies with Part 15 of the FCC-A Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful Interference
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this device in
a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his/her own expense.
DéclarationdeconformitéFCC
Ce produit est conforme à la partie 15 des règles de la FCC -A
Utilisation est soumise aux conditions suivantes:
1. Ce dispositif ne doit pas causer des interférences nuisibles
2. Cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent causer un mauvais
fonctionnement.
REVISED 2017-07-01 PREFACE
DRAWING NO. LP0982-B TRADEMARK AND REGISTRATION ACKNOWLEDGMENTS
iv N-Tron®Series NT24k®Modular Hardware Manual
Note: Cet équipement a été testé et jugé conforme aux limites de la classe A des appareils
numériques , conformément à la partie 15 des règles de la FCC . Ces limites sont conçues pour
fournir une protection raisonnable contre les interférences nuisibles dans une installation résiden-
tielle . Cet équipement génère, utilise et peut émettre de l'énergie radiofréquence et, si il n’est pas
installé et utilisé conformément aux instructions, peut causer des interférences nuisibles aux com-
munications radio. L'utilisation de cet appareil dans une zone résidentielle est susceptible de pro-
voquer des interférences nuisibles, auquel cas l'utilisateur sera tenu de corriger les interférences à
ses propres frais .
IndustryCanada/IndustrieCanada
This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions; (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des
règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas
causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.
EnvironmentalImpactStatement
Red Lion equipment contains no hazardous materials as defined by the United States Environmental Protection
Agency (USEPA). Red Lion recommends that all failed product be returned to Red Lion for failure analysis and
proper disposal.
ToxicEmissions
Red Lion equipment releases no toxic emissions.
TrademarkandRegistrationAcknowledgments
Ethernet™ is a registered trademark of Xerox Corporation.
EtherNet/IP™and CIP™are registered trademarks of ODVA™.
All other company and product names are trademarks of their respective owners.
ReleaseNotesandDocumentUpdates
The hard copy and electronic media versions of this document are revised only at major releases and therefore,
may not always contain the latest product information. As needed, Documentation Notes and or Product Bulletins
may be provided between major releases to describe any new information or document changes.
The latest online version of this document and all product updates can be accessed through the Red Lion web site
at http://www.redlion.net
PublicationHistory
The following information lists the release history of this document.
ISSUE/REVISION RELEASE DATE CONTENT DESCRIPTION
Revised 2014-01-23 January 2014 Document Updates
Revised 2015-03-17 March 2015 Format Changes
Revised 2016-04-26 April 2016 Revised with updated ODVA requirements. Added
safety updates.
Revised 2017-07-01 July 2017 Format changes and regulatory update
N-Tron®Series NT24k®Modular Hardware Manual v
PREFACE REVISED 2017-07-01
ADDITIONAL PRODUCT INFORMATION DRAWING NO. LP0982-B
RelatedDocuments
Visit the Technical Resources page on the Red Lion website at the following link to view available documents
related to this product.
http://www.redlion.net/documentation/red-lion-documentation
DocumentComments
Red Lion appreciates all comments that will help us to improve our documentation quality. The user can submit
AdditionalProductInformation
Additional product information can be obtained by contacting the local sales representative or Red Lion through the
contact numbers and/or e-mail addresses listed on the inside of the front cover.
CautionsandWarnings/MisesenGardeetAvertissements
Warnings apply to situations where personal injury or death may result.
Cautions apply to where reduced function or damage to equipment may result.
GeneralSafetyCautionsandWarnings/PrécautionsetAvertissementsdeSécuritéGénérale
CAUTION: If the equipment is used in a manner not specified by Red Lion, the protection
provided by the equipment may be impaired.
ATTENTION: Si l' N équipement est utilisé d'une manière non spécifiée par Red Lion, la protec-
tion fournie par l'équipement peut être compromise.
CAUTION: Donotremoveanyofthecovers.Therearenoserviceablepartswithintheunit. Do
notsubstituteunauthorizedpartsormakeunauthorizedmodificationstotheunit.
ATTENTION: Neretirezaucundescouvercles.Iln'yapasdespiecesutilisablesàl'intérieurde
l'appareil. Nepasremplacerlespiècesnon‐autoriséesoueffectuerdesmodificationsnon‐
autoriséesdel'appareil.
REVISED 2017-07-01 PREFACE
DRAWING NO. LP0982-B CAUTIONS AND WARNINGS / MISES EN GARDE ET AVERTISSEMENTS
vi N-Tron®Series NT24k®Modular Hardware Manual
ElectricalSafetyWarnings/AvertissementsdeSécuritéÉlectrique
WARNING - Never install or work on electrical equipment or cabling during periods of lightning
activity.
AVERTISSEMENT‐Nejamaisinstalleroutravaillersuréquipementélectriqueoudecâblage
pendantlespériodesd'activitédelafoudre.
CAUTION: Donotblockanyairventsontheunit.
ATTENTION: N'obstruezpaslesfentesd'aérationdel'unité.
CAUTION: Do not operate the equipment in a manner not specified by this manual.
ATTENTION: Ne pas faire fonctionner l'équipement d'une manière non spécifiée par ce manuel.
WARNING: Install only in accordance with Local and National Codes of authorities having
jurisdiction.
AVERTISSEMENT: Installer uniquement, conformément aux codes locaux et nationaux des
autorités ayant compétence.
CAUTION: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.
ATTENTION: Ne pas effectuer de services sur l'appareil s'il n'est pas qualifié pour le faire. Ne pas
substituer pièces non autorisées ou de modifications non autorisées de l'appareil.
WARNING: Properly ground the unit before connecting anything else to the unit. Units not
properly grounded may result in a safety risk and could be hazardous and may void the warranty.
See the grounding technique section of this manual for proper ways to ground the unit.
AVERTISSEMENT:L'unitédoitêtrecorrectementmiseàlaterreavanttoutraccordementà
l'unité.Unitéspascorrectementmiseàlaterrepeuventcauserunrisquedesécuritéetpour‐
raientêtredangereusesetpeuventannulerlagarantie.Voirlasectiontechniquedemiseàla
terredanscemoded'emploipourdesmoyensappropriésàlamassedel'appareil.
WARNING: Device must be supplied by a Class 2 power source (except for POE models).
AVERTISSEMENT: l'appareil doit être alimenté par une source d'alimentation de classe 2 (sauf
pour les modèles POE).
N-Tron®Series NT24k®Modular Hardware Manual vii
PREFACE REVISED 2017-07-01
CAUTIONS AND WARNINGS / MISES EN GARDE ET AVERTISSEMENTS DRAWING NO. LP0982-B
EnvironmentalSafetyCautionsandWarnings/SécuritéEnvironnementaleMisesenGardeet
Avertissements
HazardousLocationWarnings/LesAvertissementsd'EmplacementDangereux
WARNING - Do not operate the unit with the top cover removed, as this could create a shock or
fire hazard.
AVERTISSEMENT - Nepasfairefonctionnerl'unitéaveclecouvercleretiré,cecipourraitcréer
unedéchargeélectriqueouunincendie.
CAUTION: Observe proper DC Voltage polarity when installing power input cables. Reversing
voltage polarity can cause permanent damage to the unit and voids the warranty.
ATTENTION: Respectez la polarité correcte de tension DC lors de l'installation des câbles
d'alimentation d'entrée. Inversion de polarité de tension peut causer des dommages permanents à
l'appareil et annule la garantie.
WARNING: Do not operate the equipment in the presence of flammable gases or fumes. Operat-
ing electrical equipment in such an environment constitutes a definite safety hazard.
AVERTISSEMENT : Ne pas utiliser le matériel en présence de gaz ou de vapeurs inflammables.
L'utilisation de matériel électrique dans un tel environnement constitue un danger certain.
WARNING: Disconnect the power and allow to cool 5 minutes before touching.
AVERTISSEMENT: Déconnectez le câble d'alimentation et laisser refroidir 5 minutes avant de la
toucher.
CAUTION: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or
non-hazardous locations only.
ATTENTION: CetappareilestadaptépourutilisationenClasseI,Division2,GroupesA,B,C,D
ouendroitsnon‐dangereuxseulement.
WARNING: Explosion Hazard – Substitution of components may impair suitability for Class I,
Division 2.
AVERTISSEMENT - Risque d'explosion - Lasubstitutiondetoutcomposantpeutnuireàla
conformitédeClasse1,Division2.
WARNING – Explosion Hazard – Do not connect or disconnect any connections while circuit is
live unless area is known to be non-hazardous.
AVERTISSEMENT - Risque d'explosion - Ne pas brancher ou débrancher les connexions
lorsque le circuit est sous tension sauf si la zone est connue pour être non dangereux.
REVISED 2017-07-01 PREFACE
DRAWING NO. LP0982-B CAUTIONS AND WARNINGS / MISES EN GARDE ET AVERTISSEMENTS
viii N-Tron®Series NT24k®Modular Hardware Manual
SurroundingAirTemperature/TemperatureAmbiante
NT24k-DC and NT24k-AC rackmount models: -40°C to 85°C
NT24k-DR16 and NT24k-DR24 models: -40°C to 75°C
Note: Use 105 °C or higher rated copper wire, (0.22NM) 2lb/in tightening torque for field installed
conductors.
Remarque: Utilisez fil de cuivre classé 105 °C ou plus, (0.22Nm) 2 pouces/livres couple de ser-
rage pour les connecteurs installés sur le terrain.
LaserSafetyWarnings/AvertissementsdeSécuritéLaser
(Options: NTSFP-FX, NTSFP-FXE, NTSFP-SX, NTSFP-LX)
WARNING: Exposuretosomechemicalsmaydegradethesealingpropertiesofmaterialsused
inthefollowingdevices:RelayU40.
AVERTISSEMENT: L'expositionàcertainsproduitschimiquespeutdégraderlespropriétés
d'étanchéitédesmatériauxutilisésdanslesdispositifssuivants:relaisparU40.
WARNING – Explosion Hazard – Do not replace the device unless power has been switched off
or the area is known to be non-hazardous.
AVERTISSEMENT–Risqued’explosion‐Nepasremplacerl’appareilàmoinsquel’alimentation
aétécoupéeouquelazoneestconnuepourêtrenon‐dangereuse.
WARNING: Neverconnectordisconnectpowerwhenhazardousgasesarepresent.
AVERTISSEMENT:Nejamaisbrancheroudébrancherl’alimentationlorsqu’enpresencedegaz
dangereux..
CAUTION: CLASS 1 LASER PRODUCT. Do not stare into the laser.
ATTENTION: PRODUIT LASER CLASSE 1. Ne pas regarder dans le laser.
N-Tron®Series NT24k®Modular Hardware Manual ix
PREFACE REVISED 2017-07-01
REGULATORY INFORMATION DRAWING NO. LP0982-B
RegulatoryInformation
ProductSafety
ANSI/ISA 12.12.01-2013 Class I and II, Div. 2 and Class III, Div. 1 and 2, Groups A, B, C and D Hazardous
Locations
UL508 Industrial Control Equipment
CAN/CSA-C22.2 No. 213-M1987 Class I Div. 2 Hazardous Locations
CAN/CSA-C22.2 No. 14-M1987 Industrial Control Equipment
Emissions
FCC Title 47, Part 15, Radio Frequency Devices, Subpart B ANSI C63.4-2009
Industry Canada ICES-003, EN 55011; EN 61000-6-4, EN 61000-3-2, EN61000-3-3, EN 55032
Immunity
EN 55024, EN 61000-6-2; IEC 61000-4-2 (ESD); IEC 61000-4-3 (RFAM); IEC 61000-4-4 (EFT);
IEC 61000-4-5 (SURGE); IEC 61000-4-6 (RFCM); IEC 61000-4-8 (PFMF); IEC 61000-4-11 (VDI)
Other
ABS Type Approval for Shipboard Applications; EMC Directive 2014/30/EU; LV Directive 2014/35/EU GOST-R,
RoHS Compliant
KC Mark (Korea)
REVISED 2017-07-01 PREFACE
DRAWING NO. LP0982-B REGULATORY INFORMATION
xN-Tron®Series NT24k®Modular Hardware Manual
N-Tron®Series NT24k®Modular Hardware Manual 1-1
PRODUCT OVERVIEW REVISED 2017-07-01
NT24K® MODULAR SERIES COMMON FEATURES DRAWING NO. LP0982-B
Chapter1ProductOverview
1.1NT24k®ModularSeriesCommonFeatures
Red Lion’s N-Tron®series NT24k®modular switches are available in rackmount or 35mm DIN-Rail mountable
configurations with high density Gigabit ports. The NT24k offers a wide array of port configurations and power input
options that include Fast Ethernet and Gigabit speeds in copper or fiber. The hot-swappable port modules are
auto-detected and configured by the switch, adding new definition to plug-and-play performance. Housed in rugged
hardened enclosures, the NT24k series features extended shock and vibration specifications (bulkhead mount
required to meet requirements), wide operating temperature ratings and best-in-class technology.
1.1.1Connectivity
The NT24k series switches feature hot-swappable connectivity modules. These modules are available in Fast or
Gigabit Ethernet, and are optionally available with copper, fiber or SFP ports. The NT24k accepts up to three
modules for a maximum of 24 Ethernet ports, and can be changed without removing power from the switch.
1.1.2Performance
The NT24k line of managed switches provide uncompromising performance in harsh environments including
network features like N-Ring™, VLAN, Quality of Service (QoS), port mirroring, IGMP and SNMP.
1.1.3Environmental
The NT24k series of managed switches are available in rackmount or 35mm DIN-Rail mountable configurations
with operating temperatures up to -40° to 85°C. With UL Class I, Division 2 listing and CE certifications, these
switches are built to last in the most demanding environments.
1.1.4Monitoring
The NT24k Series includes N-View monitoring technology. N-View combines switch based technology with a
Windows based OPC server and client monitoring tool. When N-View is enabled, the switch periodically autocasts
a small Ethernet packet containing switch and port statistics. The data is captured by the N-View OPC server
software and can be displayed by the provided N-View client or third party OPC client application running in the
same Windows environment. For more information, please reference the N-View Installation and User's Guide.
1.1.5Security
The NT24k series provides a high level of security utilizing IEEE 802.1x port-based network access control with
RADIUS remote server authentication and SNMPv3 communication protocol to ensure the safest connections.
REVISED 2017-07-01 PRODUCT OVERVIEW
DRAWING NO. LP0982-B NT24K® MODULAR SERIES COMMON FEATURES
1-2 N-Tron®Series NT24k®Modular Hardware Manual
1.1.6AvailableBaseModels
Part #
Total
Ports Mounting
Operating
Temperature
10/100/
1000
Copper 100 Fiber
Gig
Fiber SFP’s
18-49 VDC
Redundant
Power
Input*
90-264
VAC/90-300
VDC Power
Input
NT24k-DR16-AC 16 35mm DIN-Rail -40 °C to 75 °C Up to 16 Up to 16 Up to 16 Up to 16 - 1
NT24k-DR16-DC 16 35 mm DIN-
Rail
-40 °C to 75 °C Up to 16 Up to 16 Up to 16 Up to 16 1 -
NT24k-DR24-AC 24 35 mm DIN-
Rail
-40 °C to 75 °C Up to 24 Up to 24 Up to 24 Up to 24 - 1
NT24k-DR24-DC 24 35 mm DIN-
Rail
-40 °C to 75 °C Up to 24 Up to 24 Up to 24 Up to 24 1 -
NT24k-AC1 24 19” Rackmount -40 °C to 85 °C Up to 24 Up to 24 Up to 24 Up to 24 - 1
NT24k-AC2 24 19” Rackmount -40 °C to 85 °C Up to 24 Up to 24 Up to 24 Up to 24 - 2
NT24k-AC1-DC1 24 19” Rackmount -40 °C to 85 °C Up to 24 Up to 24 Up to 24 Up to 24 1 1
NT24k-DC1 24 19” Rackmount -40 °C to 85 °C Up to 24 Up to 24 Up to 24 Up to 24 1 -
NT24k-DC2 24 19” Rackmount -40 °C to 85 °C Up to 24 Up to 24 Up to 24 Up to 24 2 -
* Each 18-49VDC power input option includes redundant (2) power connections.
N-Tron®Series NT24k®Modular Hardware Manual 1-3
PRODUCT OVERVIEW REVISED 2017-07-01
NT24KRACKMOUNT DRAWING NO. LP0982-B
1.2NT24kRackmount
The NT24k Rackmount Managed Industrial Ethernet Switch features connectivity for up to 24 Gigabit ports in a
rugged 1U 19" rack mount enclosure. Designed to handle the most demanding environments, the NT24k supports
up to two power inputs, extreme operating temperature range and three slots to accommodate mix-and-match port
modules.
1.2.1FeaturesandBenefits
Features and Benefits
Supports up to three of the following port modules:
-40°C to 85°C operating temperature
Dual power input options:
Onboard temperature sensor
ESD and surge protecting diodes on all copper ports
Auto-sensing 10/100/1000BaseT(X), duplex and MDIX
USB configuration port
Configurable alarm contact
Optional backup/restore configuration device
Fully managed features include:
•8-port 10/100/1000BaseT(X) module
•8-port 100Base fiber module
•8-port 1000Base fiber module
•8-port Gigabit SFP module
•8-port dual mode SFP module (100Base or
1000Base SFP transceivers)
•Easily transitions to Gigabit network
requirements
•Low Voltage: 18-49 VDC
•High Voltage: 90-264 VAC or 90-300 VDC
•Jumbo frame support
•SNMP v1, v2, v3
•Web browser management
•Detailed ring map and fault location charting
•RSTP - 802.1d, 802.1w, 802.1D
•IGMP auto-configuration
•Trunking and port mirroring
•802.1Q tag VLAN and port VLAN
•802.1p QoS, port QoS and DSCP
•SNTP (Simple Network Time Protocol)
•IEEE 802.1x with RADIUS remote server
authentication
•DHCP client
•N-Ring technology with ~30ms healing
•N-Link™ redundant ring technology
•N-View™ monitoring technology
•Ethernet/IP™
•CIP™ messaging
REVISED 2017-07-01 PRODUCT OVERVIEW
DRAWING NO. LP0982-B NT24KRACKMOUNT
1-4 N-Tron®Series NT24k®Modular Hardware Manual
1.2.2NT24KRackmountSpecifications
Mechanical
Height Width Depth Weight Mount
1.9”(4.8cm) 17.5”(44.5cm) 12.7”(32.0cm) 12.85lbs(5.83kg) Rackmount 1U
Power Input
Input Voltage Steady Input Current BTU/HR
Low: 18-49 VDC
High: 90 - 264 VAC or
90 - 300 VDC
Max: 2.26 A @ 24 VDC
Max: 790 mA @ 120
VAC/450 mA @ 124
VDC
185 @ 24 VDC
365 @ 120 VAC/190 @ 124 VDC
Environmental
Operating
Temperature
Storage Temperature Operating Humidity Operating Altitude
-40°C to 85°C -40°C to 85°C 5% to 95% (non condensing) 0 to 10,000 ft.
Shock and Vibration
Shock Vibration Note
50g @ 10ms 30g, 10-200Hz, Triaxial Unit must be bulkhead mounted to achieve these
levels.
Connectors
10/100/1000BaseT:(X): Up to 24 RJ45 ports
100BaseFX: Up to 24 SC or ST fiber ports
1000BaseSX/LX: Up to 24 SC fiber ports
100BaseSX/LX SFP: Up to 24 LC fiber ports
1000BaseGX SFP: Up to 24 LC fiber ports
Recommended Minimum Wiring Clearance
Back 4” (10.16 cm)
Front 4” (10.16 cm)
N-Tron®Series NT24k®Modular Hardware Manual 1-5
PRODUCT OVERVIEW REVISED 2017-07-01
NT24KRACKMOUNT DRAWING NO. LP0982-B
1.2.3NT24KRackmountDimensions
All specifications are subject to change. Consult the company website for more information.
REVISED 2017-07-01 PRODUCT OVERVIEW
DRAWING NO. LP0982-B NT24K-DR16
1-6 N-Tron®Series NT24k®Modular Hardware Manual
1.3NT24k‐DR16
The NT24k-DR16 Managed Industrial Ethernet Switch features connectivity for up to 16 Gigabit ports in a rugged
35mm DIN-Rail enclosure.
1.3.1FeaturesandBenefits
Features and Benefits
Supports up to two of the following port modules:
-40°C to 75°C operating temperature
Power input options:
Onboard temperature sensor
ESD and surge protecting diodes on all copper ports
Auto-sensing 10/100/1000BaseT(X), duplex and MDIX
USB configuration port
Configurable alarm contact
Optional backup/restore configuration device
Fully managed features include:
•8-port 10/100/1000BaseT(X) module
•8-port 100Base fiber module
•8-port 1000Base fiber module
•8-port Gigabit SFP module
•8-port dual mode SFP module (100Base or
1000Base SFP transceivers)
•Low Voltage: 18-49 VDC
•High Voltage: 90-264 VAC or 90-300 VDC
•Jumbo frame support
•SNMP v1, v2, v3
•Web browser management
•Detailed ring map and fault location charting
•RSTP - 802.1d, 802.1w, 802.1D
•IGMP auto-configuration
•Trunking and port mirroring
•802.1Q tag VLAN and port VLAN
•802.1p QoS, port QoS and DSCP
•SNTP (Simple Network Time Protocol)
•IEEE 802.1x. with RADIUS remote server
authentication
•DHCP client
•N-Ring technology with ~30ms healing
•N-Link™ redundant ring technology
•N-View™ monitoring technology
•Ethernet/IP™
•CIP™ messaging
N-Tron®Series NT24k®Modular Hardware Manual 1-7
PRODUCT OVERVIEW REVISED 2017-07-01
NT24K-DR16 DRAWING NO. LP0982-B
1.3.2NT24k‐DR16Specifications
Mechanical
Height Width Depth Weight Mount
5.97”(15.20cm) 6.78”(17.22cm) 4.59”(11.65cm) 6.4lbs(2.9kg) 35mm DIN-Rail
Power Input
Input Voltage Steady Input Current BTU/HR
Low: 18-49 VDC
High: 90 - 264 VAC or
90 - 300 VDC
Max: 1.52 A @ 24 VDC
Max: 580 mA @ 120
VAC/300 mA @ 124
VDC
125 @ 24 VDC
268 @ 120 VAC/190 @ 124 VDC
Environmental
Operating
Temperature
Storage Temperature Operating Humidity Operating Altitude
-40°C to 75°C -40°C to 85°C 5% to 95% (non condensing) 0 to 10,000 ft.
Shock and Vibration
Shock Vibration Note
50g @ 10ms 30g, 10-200Hz, Triaxial Unit must be bulkhead mounted to achieve these
levels.
Connectors
10/100/1000BaseT:(X): Up to 16 RJ45 ports
100BaseFX: Up to 16 SC or ST fiber ports
1000BaseSX/LX: Up to 16 SC fiber ports
100BaseSX/LX SFP: Up to 16 LC fiber ports
1000BaseGX SFP: Up to 16 LC fiber ports
Recommended Minimum Wiring Clearance
Top 4” (10.16 cm)
Front 4” (10.16 cm)
REVISED 2017-07-01 PRODUCT OVERVIEW
DRAWING NO. LP0982-B NT24K-DR16
1-8 N-Tron®Series NT24k®Modular Hardware Manual
1.3.3NT24k‐DR16Dimensions
All specifications are subject to change. Consult the company website for more information.
Other manuals for NT24k Series
1
Table of contents
Other red lion Switch manuals
red lion
red lion NT24k-8TX User manual
red lion
red lion 700 series User manual
red lion
red lion MIL316-CCCC User manual
red lion
red lion NT5000 Series User manual
red lion
red lion MIL318-MMMM-MM User manual
red lion
red lion SL-2ES Series Installation instructions
red lion
red lion MIL312-1 User manual
red lion
red lion EB-GT-8ES Series Manual
red lion
red lion N-Tron Series User manual
red lion
red lion N-Tron NT24K-TX8 User manual
red lion
red lion N-Tron Series Installation instructions
red lion
red lion EL212 User manual
red lion
red lion N-Tron NT24k Modular Series User manual
red lion
red lion NT Series Manual
red lion
red lion 308FX2 User manual
red lion
red lion EL212F User manual
red lion
red lion EB Series User manual
red lion
red lion SLX SERIES Manual
red lion
red lion MIL314-MM User manual
red lion
red lion N-Tron NT24k-16M Series User manual
Popular Switch manuals by other brands
Witura
Witura WT-215W user manual
Harman
Harman AMX SOLECIS SDX-410-DX instruction manual
Dell EMC
Dell EMC S4112F-ON installation guide
Lenovo
Lenovo USB-C Travel Hub quick start guide
EtherWAN
EtherWAN OttoE TF100 Sereis installation guide
HPE
HPE FlexNetwork 5130 HI SERIES Network management and monitoring command reference
