red lion SL Series User manual

©2014-2020 Red Lion Controls, Inc. All rights reserved. Red Lion and the Red Lion logo are
registered trademarks of Red Lion Controls, Inc. All other company and product names are
trademarks of their respective owners.
Red Lion Controls, Inc.
20 Willow Springs Circle
York, PA 17406
Inside US: [phone]
Outside US: [phone]
Hours: 8 am-6 pm Eastern Standard Time
(UTC/GMT -5 hours)
Shanghai, P.R. China: [phone] x767
Hours: 9 am-6 pm China Standard Time
(UTC/GMT +8 hours)
Netherlands: [phone]
France: [phone]
Germany: [phone]
UK: [phone]
Hours: 9 am-5 pm Central European Time
(UTC/GMT +1 hour)
Website: www.redlion.net
Support: support.redlion.net

Drawing No. LP0977 Table of Contents
Revision B
Slim Line (SL/SLX) Series i
Table of Contents
Preface ..........................................................................................................................................1
Section 1 General Information.................................................................................................3
Section 2 LED Indicators..........................................................................................................7
Section 3 Installation.................................................................................................................9
Section 4 Power Wiring...........................................................................................................21
Section 5 Communication Wiring..........................................................................................27
Section 6 Technical Specifications..........................................................................................31
Section 7 Service Information ................................................................................................35

Table of Contents Drawing No. LP0977
Revision B
ii Slim Line (SL/SLX) Series

Drawing No. LP0977 Preface
Revision B
Slim Line (SL/SLX) Series 1
Preface
This manual applies to the following products:
SL-2ES-# 2-port unmanaged Ethernet media converter
SLX-3ES-# 3-port unmanaged Ethernet media converter
SLX-3EG-1 3-port unmanaged Gigabit Ethernet converter
SLX-5EG-1 5-port unmanaged Gigabit Ethernet switch
SLX-5EG-2SFP 5-port unmanaged Gigabit Ethernet switch with 2 fiber SFPs
SL/SLX-5ES-# 5-port unmanaged Ethernet switch with 5 10/100 ports
SL/SLX-6ES-# 6-port unmanaged Ethernet switch
SL/SLX-8ES/9ES-# 8/9-port unmanaged Ethernet switch with 8 or 9 10/100 ports
SLX-8MS-# 8-port managed Ethernet switch with 8 10/100 ports
SLX-8MG-1 8-port managed Ethernet switch with 8 Gigabit ports
SLX-10MG-1 10-port managed Gigabit Ethernet switch with 10 ports
SLX-16MS-1 16-port managed Ethernet switch with 16 10/100 ports
SLX-18MG-1 18-port managed Gigabit Ethernet switch with 18 ports
FCC Statement - This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or
relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult
the dealer or an experienced radio/TV technician for help.

Preface Drawing No. LP0977
Revision B
2 Slim Line (SL/SLX) Series

Drawing No. LP0977 Section 1 General Information
Revision B
Slim Line (SL/SLX) Series 3
Section 1 General Information
Overview
This manual will help you install and maintain these industrial Ethernet switches.
Installation of these switches is very easy and they will begin to operate as soon as they
are powered up. For the unmanaged models (denoted by ES or EG in their part number)
there are no user settings so they are truly plug and play. The managed models (denoted
by MS or MG in their part number) will act as unmanaged switches until they are
configured otherwise. Refer to the managed switch software manual for configuration of
advanced network functionality.
Note: This manual only covers the installation and wiring of these switches. For
the managed models refer to the separate Software User Manuals for details on
configuring and using any of the management functions such as SNMP, RSTP,
IGMP, VLANs, security, port mirroring and much more.
Operation
Unlike an Ethernet hub that broadcasts all messages out all ports, these industrial Ethernet
switches will intelligently route Ethernet messages only out the appropriate port. The major
benefits of this are increased bandwidth and speed, reduction or elimination of message
collisions, and deterministic performance when tied with real-time systems.
These industrial Ethernet switches can support 10BaseT (10 Mbps), 100BaseT (100 Mbps)
and 1000BaseT (1000 Mbps) on their RJ45 ports (depending on the model). Each of these
ports will independently auto-sense the speed/duplex, mdi/mdix-crossover and polarity
allowing you to use straight, crossed or even mis-wired cables. Some models also have
one or more fiber optic ports for making noise immune connections up to 120 km.
Performance
Specifications
These general specifications apply to these industrial Ethernet switches. Refer to Section 6
for complete technical specifications.
Number of ports
2, 3, 5, 6, 8, 9, 10, 16 or 18 Ethernet ports
Ethernet Switch Type
Unmanaged (ES/EG models) or managed (MS/MG models)
Ethernet Switch Mode
Store and forward, wire-speed, non-blocking
Ethernet Protocols
All standard IEEE 802.3 protocols supported
RJ45 Ports Speed
10/100 or 10/100/1000 Mbps
RJ45 Ports Operation
Auto-negotiation, auto-mdi/mdix-crossover and auto-polarity
Fiber Optic Port Speed
100 Mbps (SC or ST) or 1000 Mbps (SFP/LC)
Fiber Optic Type
Multimode, singlemode, long-haul or special application
Safety
Standards
These industrial Ethernet Switches meet the following standards plus others:
Note: Some ratings may be pending on newer models. Contact Red Lion for the latest info.
Electrical safety –
CE per Low Voltage Directive and IEC61010-1
UL508
CSA per C22.2/142
See warnings below.
Note: This Equipment is Suitable for Use in Class I, Division 2, Groups A, B, C, D
or Non Hazardous Locations Only

Section 1 General Information Drawing No. LP0977
Revision B
4 Slim Line (SL/SLX) Series
Install the Managed Switches in accordance with local and national electrical codes.
Lightning Danger: Do not work on equipment during periods of lightning activity.
Do not connect a telephone line into one of the Ethernet RJ45 connectors.
EMC (emissions and immunity) –
CE per the EMC directive, EN 55022, EN 61000-6-2/4
FCC part 15 and ICES 003; Class B. See FCC statement on previous page.
Marine, maritime and offshore –
These devices, when installed in an appropriately IP rated enclosure, comply with the ABS
standards which is similar to DNV No. 2.4 and equivalent Lloyds. Please reference
product datasheet for individual specifications and agency certifications.
See warning below.
For marine and maritime compliance, do not install this product within 5 meters of a
standard or a steering magnetic compass.
WEEE compliance –
These devices comply with the WEEE directive. Do not throw away these devices in the
standard trash. Contact Red Lion regarding proper disposal.
RoHS
RoHS compliance –
These devices comply with the RoHS directive and are considered lead and other
hazardous substance free.
Hazardous Locations –
CE per ATEX directive and IEC60079-0,-15 (Zone 2)
ISA12.12.01 (Class I, Div. 2), Groups A,B,C,D
CSA per C22.2/213 (Class 1, Div. 2), Groups A,B,C,D
See warnings below.

Drawing No. LP0977 Section 1 General Information
Revision B
Slim Line (SL/SLX) Series 5
INSTALLATION AND HAZARDOUS AREA WARNINGS:
These products should not be used to replace proper safety interlocking. No software-based device (or
any other solid-state device) should ever be designed to be responsible for the maintenance of
consequential equipment or personnel safety. In particular, Red Lion disclaims any responsibility for
damages, either direct or consequential, that result from the use of this equipment in any
application.
All power, input and output (I/O) wiring must be in accordance with Class I, Division 2 wiring methods
and in accordance with the authority having jurisdiction. This equipment is suitable for use in Class I,
Division 2, Groups A, B, C, D or non-hazardous locations only.
WARNING
(EXPLOSION HAZARD)
SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY
FOR CLASS 1, DIVISION 2 (ZONE 2).
WARNING
(EXPLOSION HAZARD)
WHEN IN HAZARDOUS LOCATIONS, DISCONNECT POWER BEFORE
REPLACING OR WIRING UNITS.
WARNING
(EXPLOSION HAZARD)
DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.
WARNING
(EXPLOSION HAZARD)
IN HAZARDOUS OR POTENTIALLY HAZARDOUS LOCATIONS, DO
NOT SEPARATE ANY PART OF THE UNIT WHEN ENERGIZED. USE
THE UNIT FOR INTERNAL CONNECTIONS ONLY.
INSTRUCTIONS D’INSTALLATION ET D’UTILISATION:
Ces produits ne doivent pas être utilisés pour remplacer le verrouillage de sécurité approprié. Aucun
dispositif basé sur un logiciel (ou tout autre dispositif à l'état solide) devraient jamais être conçus pour
être responsable de l'entretien de l'équipement consécutifs ou la sécurité du personnel. En particulier,
Red Lion décline toute responsabilité pour les dommages, directs ou indirects, résultant de l'utilisation de
cet équipement dans n'importe quelle application.
Tout courant, câblage entrée et sortie (I / O) doit être conforme aux méthodes de câblage à la Classe I,
Division 2 et conformément à l'autorité compétente. Cet équipement est adapté à une utilisation en
Classe I, Division 2, Groupes A, B, C, D ou environnements non-dangereux seulement.
AVERTISSEMENT
(RISQUE
D’EXPLOSION)
LA SUBSTITUTION DE TOUT COMPOSANT PEUT NUIRE À LA
CONFORMITÉ DE CLASSE I, DIVISION 2 (ZONE 2).
AVERTISSEMENT
(RISQUE
D’EXPLOSION)
LORSQUE DANS DES ENDROITS DANGEREUX, DÉBRANCHEZ LE
CORDON D’ALIMENTATION AVANT DE REMPLACER OU DE
BRANCHER DES MODULES.

Section 1 General Information Drawing No. LP0977
Revision B
6 Slim Line (SL/SLX) Series
AVERTISSEMENT
(RISQUE
D’EXPLOSION)
NE DÉBRANCHEZ PAS L’ÉQUIPEMENT PENDANT QUE LE CIRCUIT
EST DIRECT OU À MOINS QUE L’ENVIRONNEMENT SOIT CONNU
POUR ÊTRE LIBRE DE CONCENTRATIONS INFLAMMABLES.
AVERTISSEMENT
(RISQUE
D’EXPLOSION)
DANS LES ENDROITS DANGEREUX OU POTENTIELLEMENT
DANGEREUX, NE PAS SÉPARER UNE PARTIE DE L'UNITÉ SOUS
TENSION. SEULEMENT UTILISEZ L'APPAREIL POUR LES
CONNEXIONS INTERNES.