ReelCraft 5400 ELP User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Remove 1/4-20 hex nuts (4) which fasten the hose guide enclosure to the reel back cover and pull off the
enclosure.
2. Wind spool flange clockwise-facing swivel-until spring is tight.
3. Back off three turns and latch.
4. Insert hose through roller guide.
5. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Operating Instructions
Series 5000 Spring Driven Hose Reels
Low Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 490-884 Rev: 3/2018
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the 1/4-20 hex nuts (4) fastening the hose guide enclosure to the reel back cover. Shift the hose guide
enclosure to the desired position and replace the 1/4-20 hex nuts. NOTE: For proper installation in wall mount
applications, ensure reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause
latching issues.
Dimensions
A 15”
B16 1/4”
C9 3/4”
D2 1/2”
E 7”
5400 ELP 5435 ELP 5615 ELP 5630 ELP
5420 ELP 5450 ELP 5620 ELP 5635 ELP
5425 ELP 5600 ELP 5625 ELP

Series 5000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
35
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 500102 1 Case and Cover Assembly 11 500004 1 Reel Cover 23 300002 7 10-32 x 1/2” Screw
2 300001 4 10-32 x 3/8” Screw 12 300070 4 1/4-20 Nyloc Nut 24 S400012 1 Latch Bushing
3 S600886 1 Swivel Assembly 13 500101 1 Base Assembly 25 400020 7 O-ring
4 300031 1 1” Snap Ring 15 S261360 1 Spring Case Stud 26 S400109 1 Latch Plate Assembly
5 300034 4 Spacing Washer 16 S500103 1 Spring Case Assembly 27 300035 1 10-32 x 1” Mach. Screw
6 S295-102 3 1/4-10 x 5/8” Hex Screw 17 300006 1 3/8-16 x 1/2” Set Screw 28 3-117440 1 Hose Clamp
7 260022 1 Sheave Flange 19 S82-15 8 10-32 x 3/8” Nyloc Nut 30 S400015 1 Main Shaft
8 500006 1 Sheave Disk 20 S400021 1 Latch Bumper 33 S260019 1 Guide Roller Pin Kit
9 S500019 1 Latch Cam 21 S32-136 1 10-24 x 3/8” Screw 34 HR2012 1 Hose Guide Assembly
10 S260648 1 Spring Arbor 22 S400018 1 Latch Spring 35 261650-1 2 1/4-20 Nyloc Nut
Item # Description # Req. 5400 ELP 5420 ELP 5425 ELP 5435 ELP 5450 ELP
14 Drive Spring Assembly 1 S503755 S503755 S503755 S503755 S503755
31 Hose Assembly 1 None 601001-20 601001-25 601001-35 601001-50
32 Bumper Stop 1 None 1-HR1004-A 1-HR1004-A 1-HR1004-A 1-HR1004-A
Item # Description # Req. 5600 ELP 5615 ELP 5620 ELP 5625 ELP 5630 ELP 5635 ELP
14 Drive Spring Assembly 1 504240 504240 504240 504240 504240 504240
31 Hose Assembly 1 None 601011-15 601011-20 601013-25 S601011-30 S601013-35
32 Bumper Stop 1 None 1-HR1004 1-HR1004 1-HR1004 1-HR1004 1-HR1004