ReelCraft D8400 OHP User manual

Operating Instructions
Series D8000 Spring Driven Hose Reels
High Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 4788-84 Rev: 1/2016
D8400 OHP D8450 OHP D8630 OHP D8650 OHP
D8440 OHP D8600 OHP D8640 OHP
1. Do not use reel at higher pressures or temperatures
than listed on the back of this bulletin.
2. Remove all spring tension before beginning
dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Dimensions
A21 1/8”
B 19”
C7 7/8”
D3 3/4”
E9 1/4”
Caution: When changing guide arm positions, the U-bolt must
be placed in the proper location as instructed below. The reel
can “latch out” during use if this instruction is not adhered to.

Series D8000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Description #
Req. D8400 OHP D8440 OHP D8450 OHP D8600 OHP D8630 OHP D8640 OHP D8650 OHP
1Hose Assembly 1 None S8-260044 S9-260044 None S3-260044 S4-260044 S5-260044
2Swivel Assembly 1 S602033 S602033 S602033 S602033 S602033 S602033 S602033
3Sheave Assembly 1 S260011 S260011 S260011 S260011 S260011 S260011 S260011
4Drive Spring Assembly 1 S260053 S260053 S260053 S260053 S260053 S260053 S260053
5Spring Arbor Assembly 1 S600621 S600621 S600621 S600621 S600621 S600621 S600621
6 Gasket 1 S260069 S260069 S260069 S260069 S260069 S260069 S260069
7Spring Case Assembly 1 S260074 S260074 S260074 S260074 S260074 S260074 S260074
810-32 Hex Nut 6 S300011 S300011 S300011 S300011 S300011 S300011 S300011
9Main Shaft 1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1
10 1¼” Snap Ring 3 300007 300007 300007 300007 300007 300007 300007
11 Bumper Stop 1 None 1-HR1004-3A 1-HR1004-3A None 1-HR1004-A 1-HR1004-A 1-HR1004-A
13 Guide Arm / Roller Assembly 1 260007 260007 260007 260007 260007 260007 260007
14 5/16-18 x 1¼” Screw 3 507286 507286 507286 507286 507286 507286 507286
15 1/2-13 Set Screw 1 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86
16 1/2-20 Hex Nut 1 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8
17 Base Casting 1 260073 260073 260073 260073 260073 260073 260073
18 Latch Spring 1 S260067 S260067 S260067 S260067 S260067 S260067 S260067
19 Latch Bushing 1 S400012 S400012 S400012 S400012 S400012 S400012 S400012
20 10-24 x 1” Screw 1 300042 300042 300042 300042 300042 300042 300042
21 Latch Pawl Ass’y 1 S600083 S600083 S600083 S600083 S600083 S600083 S600083
22 3/8-24 Hex Jam Nut 1 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106
23 Spring Case Stud 1 S260031 S260031 S260031 S260031 S260031 S260031 S260031
24 U-bolt 1 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440
25 1/4-20 Nyloc Nut 2 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1
27 Swivel Union 1 S257-72 S257-72 S257-72 S257-72 S257-72 S257-72 S257-72
Hose I.D. and Length 1/4” x 50’ 1/4” x 40’ 1/4” x 50’ 3/8” x 50’ 3/8” x 30’ 3/8” x 40’ 3/8” x 50’
Reel Inlet Connection 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT
Max. Operating Pressure 5000 PSI 5000 PSI 5000 PSI 5000 PSI 4800 PSI 4800 PSI 4800 PSI
Max. Operating Temperature 210 °F 210 °F 210 °F 210 °F 210 °F 210 °F 210 °F
1
2
345678910
11
13
14
15
16
17
18
19
20
21
22
23
24
25
27