ReelCraft D8640 EMP User manual

Operating Instructions
Series D8000 Spring Driven Hose Reels
Enclosed Medium Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 4808-84 Rev: 1/2016
D8640 EMP D8800 EMP D8840 EMP
D8650 EMP D8830 EMP D8850 EMP
Four 1/2” diameter mounting holes
Dimensions
A21 5/8”
B20 7/8”
C7 7/8”
D3 3/4”
E10 1/2”
B
A
C
DE
A
B
C
D
E
21 7/8"
20 7/8"
7 3/4"
3 3/4"
10 1/2"
1. Do not use reel at higher pressures or temperatures
than listed on the back of this bulletin.
2. Remove all spring tension before beginning
dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Remove 1/4-20 hex nuts (4) which fasten the hose guide enclosure to the reel back cover, and pull off the
enclosure.
2. Wind spool flange clockwise-facing swivel-until spring is tight.
3. Back off two turns and latch.
4. Insert hose through roller guide.
5. Connect hose fitting to female outlet ell..
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing the
1/4-20 hex nuts fastening the hose guide enclosure to the reel back cover. Shift the guide enclosure to the desired
position and replace the 1/4-20 hex nuts.
Caution: When changing guide arm positions, the U-bolt must
be placed in the proper location as instructed below. The reel
can “latch out” during use if this instruction is not adhered to.

Series D8000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Description #
Req. D8640 EMP D8650 EMP D8800 EMP D8830 EMP D8840 EMP D8850 EMP
1Hose Guide Assembly 1 260032 260032 260032 260032 260032 260032
210-32 x 1/2” Screw 4 300002 300002 300002 300002 300002 300002
4Bumper Stop Assembly 1 1-HR1004-3 1-HR1004-3 None 2-HR1004-3 2-HR1004-3 2-HR1004-3
5Hose Assembly 1 S4-260043 S5-260043 None S6-260043 S7-260043 S8-260043
6Swivel Assembly 1 S600300 S600300 S600300 S600300 S600300 S600300
7Sheave Assembly 1 S260011 S260011 S260011 S260011 S260011 S260011
8Drive Spring Assembly 1 S260053 S260053 S260053 S260053 S260053 S260053
9Spring Arbor Assembly 1 S600621 S600621 S600621 S600621 S600621 S600621
10 Gasket 1 S260069 S260069 S260069 S260069 S260069 S260069
11 Spring Case Assembly 1 S260074 S260074 S260074 S260074 S260074 S260074
12 10-32 Hex Nut Nyloc 6 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15
13 Main Shaft 1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1
14 1-1/4” Snap Ring 3 300007 300007 300007 300007 300007 300007
15 5/16-18 Cap Screw 4 300003 300003 300003 300003 300003 300003
16 1/4-20 Nyloc Nut 2 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1
17 Reel Cover 1 260036 260036 260036 260036 260036 260036
18 1/2-13 Set Screw 1 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86
19 1/2-20 Hex Nut 1 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8
20 Base Casting 1 260073 260073 260073 260073 260073 260073
21 Latch Spring 1 S260067 S260067 S260067 S260067 S260067 S260067
22 Latch Bushing 1 S400012 S400012 S400012 S400012 S400012 S400012
23 10-24 x 1” Screw 1 300042 300042 300042 300042 300042 300042
24 Latch Pawl Assembly 1 S600083 S600083 S600083 S600083 S600083 S600083
25 3/8-24 Hex Jam Nut 1 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106
26 Spring Case Stud 1 S260031 S260031 S260031 S260031 S260031 S260031
27 U-bolt 1 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440
29 Swivel Union 1 S257-26 S257-26 S257-26 S257-26 S257-26 S257-26
30 Case and Cover Assembly 1 260016 260016 260016 260016 260016 260016
Hose I.D. and Length 3/8” x 40’ 3/8” x 50’ None 1/2” x 30’ 1/2” x 30’ 1/2” x 30’
Reel Inlet Connection 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT
Max. Operating Pressure 2600 PSI 2600 PSI 3250 PSI 3250 PSI 3250 PSI 3250 PSI
Max. Operating Temperature 210 °F 210 °F 210 °F 210 °F 210 °F 210 °F
1
2
4
567
8910
11 12
13
14 15 16 17
18
19
20
21
22
23
24
25
26
27
16
29
30