Regency Zero Clearance Direct Vent Gas Fireplace... User manual

P36 - P36D Zero Clearance Direct Vent Gas Fireplace
Model P36-NG4 P36-LP4 P36D-NG1 P36D-LP1
Fuel Type Natural Gas Propane Natural Gas Propane
Minimum Supply
Pressure
5” W.C.
(1.25 kPa)
12” W.C.
(3.00 kPa)
5” W.C.
(1.25 kPa)
12” W.C.
(3.00 kPa)
Manifold
Pressure - High
3.8” W.C.
(0.95 kPa)
11” W.C.
(2.74 kPa)
3.8” W.C.
(0.95 kPa)
11” W.C.
(2.74 kPa)
Manifold
Pressure - Low
1.1” W.C.
(0.27 kPa)
2.9” W.C.
(0.72 kPa)
1.1” W.C.
(0.27 kPa)
2.9” W.C.
(0.72 kPa)
Orifice Size #37 DMS #52 DMS #37 DMS #52 DMS
Minimum Input 15,500 BTU/h
(4.54 kW)
15,000 BTU/h
(3.96 kW)
15,500 BTU/h
(4.54 kW)
15,000 BTU/h
(3.96 kW)
Maximum Input 30,000 BTU/h
(8.79 kW)
30,000 BTU/h
(8.79 kW)
30,000 BTU/h
(8.79 kW)
30,000 BTU/h
(8.79 kW)
Vent Sizing 4” Inner / 6 5/8”
Outer
4” Inner / 6 5/8”
Outer
4” Inner / 6 5/8”
Outer
4” Inner / 6 5/8”
Outer
A
D
CF
E
A
B
Unit Dimensions Description P36 P36D
A Front Face Width 36” (914mm) 36” (914mm)
B Rear Firebox Width 33-1/4” (838mm) 33-1/4” (838mm)
C Front Face Height 30-1/2” (775mm) 30-1/2” (775mm)
D Height w/ Standoff 36” (914mm) 37” (940mm)
E Unit Depth 12-3/4” (324mm) 17-1/8” (435mm)
F Height to Vent 32-1/2” (826mm) 32-1/2” (826mm)
Framing Dimensions Description P36 P36D
G Framing Width* 36-1/4” (921mm) 36-1/4” (921mm)
H*** Framing Height* *** 36-1/4” (921mm)*** 37-1/4” (946mm)***
I Framing Depth* 12-3/4” (324mm) 17-1/8” (435mm)
J Corner Wall Length 42-7/16” (1078mm) 48” (1219mm)
KCorner Facing Wall
Width 60” (1524mm) 68” (1727mm)
L Framed Chase Ceiling 46” (1168mm) 46-1/2” (1181mm)
M Vent Centerline Height 40-1/2” (1029mm) 40-1/2” (1029mm)
N Gas Connection Height 2” (51mm) 2” (51mm)
O Gas Connection Inset 3-1/2” (89mm) 3-1/2” (89mm)
P Gas Connection Width 4” (102mm) 4” (102mm)
G
H
I
K
J
L
O
P
N
M
10" (254mm)
dia. Hole through
wall Vent.
Opening for gas
connection
Top Header
Drywall
(or other
facing)
*If using the Barcelona Surround, Kensington, Balmoral, or
Tripoli Screen Door please note that framing and facing must
be non combustible (12” on top and 6” on both sides) and that
the Barcelona is only approved for installation with a single
sidewall.
P36 - P36D Gas Fireplace
Approved Venting Systems
Flex Vent Systems: FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems: Simpson Dura-Vent® Direct Vent GS
American Metal Products Ameri Vent
Security Secure Vent®
Selkirk Direct-Temp.
***Important: Framing height requires consideration of the hearth
depth. Dimension H = H + the thickness of installed hearth.
Please refer to Page 11 (Exterior Vent Terminations)
for additional guidelines on vent locations.
35June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

Framing and Finishing
1) Determine the total thickness of facing material (e.g. drywall plus
ceramic tiles) to allow the finished surface to be flush with the front
of the unit. Total facing thickness can vary from 1/2” (13mm) to
1-1/4” (32mm) thick.
2) Frame in the enclosure for the unit with framing material.
Note: Header for the P36 must be installed vertically to maintain
clearances to combustible materials. Non combustible header may
be installed horizontally.
3) For exterior walls, insulate the enclosure to the same degree as
the rest of the house, apply vapor barrier and drywall, as per local
installation codes. (Do not insulate the fireplace itself.)
4) The top of the unit must not be closer than 32” (813mm) to the
ceiling.
5) Combustible material may be brought up to the top and sides of
the unit and be covered with ceramic tiles, bricks, rock or other
suitable combustible finishing materials.
If using the Barcelona Surround, Kensington, Balmoral, or
Tripoli Screen Door please note that framing and facing must
be non combustible (12” on top and 6” on both sides) and that
the Barcelona is only approved for installation with a single
sidewall.
Note: The unit does not have to be completely enclosed in a
chase. The clearance on top of the unit is 0” to the standoffs
so combustible building materials can be laid directly on top
of the standoffs. You must maintain proper clearances from
the vent to combustible materials (See Below).
6) Use metal studs for framing where the minimum clearance from
the vent to combustible material cannot be maintained.
Drywall
Mantel Clearances
2
0
12 64
810
0
Side View
Top o f
Unit
12" (305mm)
3-1/2" (89mm)
7-1/2"(191mm)
A
To base
of Unit
Standoff
BC
D
6" Side Wall
5"
2"
Mantel leg
Mantel leg
P36 - P36D
Allowable mantel leg
projection.
3"
1-1/2"
8" Single Sidewall when using the Barcelona Surrround
Mantel Clearances ABCD
with Flush Glass or
Hampton Cast
30-1/2”
(778mm) 14” (356mm) 10” (254mm) 7” (178mm)
with Bay Option 30-1/2”
(778mm) 13” (330mm) 10” (254mm) 7” (178mm)
with Flush Glass and
Barcelona Surround
30-1/2”
(778mm) 17” (432mm) 12” (305mm) 8” (203mm)
with Tripoli Screen Door,
Kensington, or Balmoral
Front
30-1/2”
(778mm) 20” (508mm) N/A 12” (305mm)
P36 - P36D Gas Fireplace
Combustible Mantels
Because of the extreme heat this fireplace emits, the mantel
clearances are critical. Combustible mantel clearances from top of
the louvers are shown in the diagram below. Mantel may be installed
anywhere in the shaded area or higher.
Note: If desired a non-combustible mantel may be installed at a
lower height.
Note: Ensure the paint that is used on the mantel and the facing
is “heat resistant” or the paint may discolour.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram below:
Clearances are from the finished edge of the unit or an installed front.
Maximum
1-1/2” projection at 2”
minimum clearance.
WARNING
Failure to maintain required clearances is a major cause of
chimney related fires. Installation of this fireplace must comply
with these clearances.
Clearance: Dimension Measured From:
A: Mantel Height 7” (178mm) Minimum (Additional on this page)
B: Sidewall 6” (152mm) Side of installed front
Sidewall: Barcelona Only 8” (203mm) Approved for single sidewall only
C: Ceiling 32” (813mm) Top of installed unit
D: Mantel Depth 12” (305mm) Maximum (Additional on this page)
E: Alcove Width 48” (1219mm) Sidewall to Sidewall (Minimum)
F: Alcove Depth 36” (914mm) Front to back wall (Maximum)
Top of Hearth must not be higher than the base of the firebox.
Vent Clearances Clearance Dimension
Horizontal - Top 2” (51mm)
Horizontal - Side 1-1/2” (38mm)
Horizontal - Bottom 1-1/2” (38mm)
Vertical (Flex or Rigid) 1-1/4” (32mm)
E
B
B
A
C
D
F
Clearance Requirements
36 June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

6-7/8"
(173mm) dia.
Flue pipe
4" (102mm)
dia. flue pipe Termination Cap
Part #946-523/P
AstroCap
spring
spacer
Wall Thimble (2 pc)
FPI Direct Vent System (Flex)
Horizontal Terminations Only
These venting systems, in combination with the P36 / P36D Direct Vent
Gas Fireplace, have been tested and listed as a direct vent heater system
by Warnock Hersey. The location of the termination cap must conform
to the requirements in the Vent Terminal Locations diagram.
FPI Direct Vent (Flex) System Termination Kits include all the parts
needed to install the P36 / P36D using a flexible vent.
FPI Kit # Length Contains:
#946-515 4 Feet 1) 6-5/8” flexible liner (Kit length)
2) 4” flexible liner (Kit length)
3) spring spacers (3)
4) thimble (2)
5) AstroCap termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) S.S. screws #8 x 1-1/2” drill point, (4)
#946-516 10 Feet
Notes:
1) Liner sections should be continuous without any joints or seams.
2) Only Flex pipe purchased from Regency may be used for Flex
installations.
3) Horizontal sections must be supported every 3 feet.
Alternate Horizontal
Termination Caps
Alternate:
Horizontal
Riser Vent
Terminal
Part# 640-530/P
Snorkel Terminations
Snorkel Terminations:
For installations requiring a vertical rise on the exterior of the building,
14-inch and 36-inch tall Snorkel Terminations and the Riser Vent are
available. Follow the same installation procedures as used for standard
Horizontal Termination. NEVER install the snorkel upside down.
Below Grade Snorkel Installation (Dura-Vent Only)
If the Snorkel Termination must be installed below grade, i.e. basement
application, proper drainage must be provided to prevent water from
entering the Snorkel Termination. Refer to Rigid Pipe Installation
instructions for details. Do not attempt to enclose the Snorkel within the
wall, or any other type of enclosure.
P36 - P36D Gas Fireplace
If required by the external termination location the listed
alternate termination caps may be used. (Refer to Page 11)
37June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

Rigid Pipe Venting
Horizontal or Vertical Terminations
Venting Arrangements - Vertical
Terminations
Rigid Pipe System
(Propane & Natural Gas)
The P36 / P36D is approved for a maximum 40 ft. straight vertical, with
Rigid Pipe vent systems for Propane and Natural Gas.
The lightly shaded area,
68
2
0
410
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
12
, in the diagram shows allowable venting
configurations with a maximum of two 45° elbows allowed.
The darker shaded area,
68
2
0
410
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
12
, in the diagram shows allowable venting
configurations using two 90° elbows.
• Vent must be supported at offsets.
• Horizontal sections must be supported every 3 feet
• Firestops are required at each floor level and whenever
passing through a wall.
• Maintain clearances to combustible materials.
• Minimum of 1’ pipe section between elbows.
Note: Must use optional flue adapter when using Rigid Pipe (Part
# 510-994).
Maximum: 40 ft. (12.2m)
Minimum 10’6” (3.2m)
Minimum 8’6” (2.6m)
Max. 10’ (3m)(centerline to centerline)
Minimum 12” (305mm)
Maximum: 27 ft. (8.2m)
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
Vertical Height (Feet)
32
34
36
38
68
2
0
410 12
12 16 18
14
20 26 28
22 24 30
Rigid Pipe Adapter
(Part# 510-994)
Pipe Length
Vertical
Terminal
Storm Collar
Part # 953
Flashing
943 or 943S
Ceiling Firestop
(Part # 963)
Pipe
Length
Adj.Pipe Length
11" - 14-5/8"
90 Elbow
o
Horizontal
Termination Cap
(Part #946-523/P)
Wall Thimble
Part # 942
Vinyl Siding
Standoff (Optional)
Part #950
P36 - P36D Gas Fireplace
If required by the external termination location the listed
alternate termination caps may be used. (Refer to Page 11)
Alternate Horizontal
Termination Caps
Alternate:
Horizontal
Riser Vent
Terminal
Part# 640-530/P
38 June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

Vertical Venting
with Two (2) 90° Elbows
Two 45° elbows = One 90° elbow
Option V H V+ V1 Maximum total pipe: length, of
all sections, must not exceed
30 feet.
Total horizontal sections must
not exceed 8 feet.
Minimum of 1 foot between
90° elbows is required.
A) 0’ Min. 2’ Max. 1’ Min.
B) 1’ Min. 4’ Max. 3’ Min.
C) 2’ Min. 5’ Max. 4’ Min.
D) 3’ Min. 6’ Max. 5’ Min.
E) 4’ Min. 7’ Max. 6’ Min.
F) 5’ Min. 8’ Max. 7’ Min.
Vertical Venting
with Three (3) 90° Elbows
Two 45° elbows = One 90° elbow
Option V H + H1 V+ V1 Maximum total pipe: length, of
all sections, must not exceed
30 feet.
Total horizontal sections must
not exceed 8 feet.
Minimum of 1 foot between
90° elbows is required.
A) 0’ Min. 2’ Max. 2’ Min.
B) 1’ Min. 2’ Max. 3’ Min.
C) 2’ Min. 3’ Max. 4’ Min.
D) 3’ Min. 4’ Max. 6’ Min.
E) 4’ Min. 5’ Max. 7’ Min.
F) 5’ Min. 6’ Max. 8’ Min.
G) 6’ Min. 7’ Max. 9’ Min.
H) 7’ Min. 8’ Max. 10’ Min.
P36 - P36D Gas Fireplace
39June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

16
2
2
0
0
12
12
6
6
18
4
40-1/2"
(1029mm)
Minimum
Height
Requirement
4
14
8
8
10
10 14 16 18 20
Vertical Height (Feet)
Horizontal (Feet)
P36D ONLY
Please refer to Page 11 (Exterior Vent Terminations)
for additional guidelines on vent locations.
P36 - P36D Gas Fireplace
Venting Arrangements - Horizontal
Terminations
This diagram shows all allowable combinations of vertical runs with
horizontal terminations, using one 90º elbow (two 45º elbows equal
one 90º elbow).
The lightly shaded area,
68
2
0
410
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
12
, in the diagram shows allowable
combinations when installing a P36
The darker shaded area,
68
2
0
410
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
12
, in the diagram shows additional allowable
combinations when installing a P36D.
Note: Must use optional flue adapter (Part # 510-994) when using
Rigid Pipe.
• Maintain clearances to combustibles.
• Horizontal vent must be supported every 3 feet.
• Firestops are required at each floor level and whenever passing
through a wall.
A vent guard may be required as per local codes, refer to page 11 for
“Exterior Vent Termination Locations”.
Note: FPI Direct Vent System (Flex) is only approved for horizontal
terminations.
40 June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

Horizontal Venting
with Two (2) 90° Elbows
Two 45° elbows = One 90° elbow
Option V H+ H1 Maximum total pipe: length, of
all sections, must not exceed
30 feet.
Total horizontal sections must
not exceed 8 feet.
Minimum of 1 foot between
90° elbows is required.
A) 0’ Min. 2’ Max.
B) 1’ Min. 3’ Max.
C) 2’ Min. 4’ Max.
D) 3’ Min. 5’ Max.
E) 4’ Min. 6’ Max.
F) 5’ Min. 7’ Max.
F) 6’ Min. 8’ Max.
Horizontal Venting
with Three (3) 90° Elbows
Two 45° elbows = One 90° elbow
Option V H V+ V1 H + H1 Maximum total
pipe: length, of
all sections, must
not exceed 30
feet.
Total horizontal
sections must not
exceed 8 feet.
Minimum of 1
foot between
90° elbows is
required.
A) 0’ Min. 1’ Max. 1’ Min. 2’ Max.
B) 1’ Min. 2’ Max. 3’ Min. 3’ Max.
C) 2’ Min. 2’ Max. 5’ Min. 4’ Max.
D) 3’ Min. 2’ Max. 7’ Min. 5’ Max.
E) 4’ Min. 3’ Max. 9’ Min. 6’ Max.
F) 5’ Min. 4’ Max. 10’ Min. 7’ Max.
G) 6’ Min. 5’ Max. 11’ Min. 8’ Max.
H) 7’ Min. 6’ Max. 12’ Min. 9’ Max.
P36 - P36D Gas Fireplace
41June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces

Vertical termination with co-linear
flex system
The appliance must not be connected to a chimney flue
serving a separate solid fuel burning appliance.
Masonry chimneys may take various contours which the flexible liner
will accommodate. However, keep the flexible liner as straight as
possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the
termination cap.
This appliance is designed to be attached to two 3” (76mm) co-linear
aluminium flex running the full length of the chimney. See the Venting
Arrangements for minimum and maximum heights.
Required Parts:
Part # Description
946-529 Co-linear DV Vertical Termination Cap
948-305 3” Flex - 35 ft.
946-563 Coaxial to Co-linear Adapter Kit which contains
the following: Co-linear Flex Adapter Outer Pipe
Inner Pipe Adapter
510-994 Flue Adapter
945 45º Elbow
Alternate Approved Caps
980 Vertical Termination Cap
991 High Wind Cap
923GK 3” Co-linear Adapter with flashing
The shaded area in the diagrams
show the allowable vertical
terminations.
Please refer to Page 11
(Exterior Vent Terminations)
for additional guidelines on
vent locations.
Flex Liner
Exhaust
Flue
A maximum
of two certified
joiner kits
may be used
per length.
#948-305 (35 ft)
Air Intake
Co-linear DV
Vertical Termination
Cap # 946-529
Co-Linear
Flex
Adapter
with Kit#
946-563
Outer
Pipe
with Kit#
946-563
Inner Pipe
Adapter
with Kit#
946-563
Rigid Pipe Adapter
# 510-994 90 Degree
Elbow
Pipe Length
8' Min.
40-1/2”
30' Max.
30
Horizontal Distance (Feet)
Vertical Height (feet)
2’ max.
P36 - P36D Gas Fireplace
42 June 2007 Regency Product Specifications Book
Gas Fireplaces
Gas Fireplaces