Regency City Series User manual

City Series CB60E | 1
City Series CB60E Gas Fireplace
MODEL CB60E-NG CB60E-LP
Fuel Type Natural Gas Propane
Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)
Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62
kPa)
Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)
Orifice Size -Altitude 0-4500 ft # 32 DMS # 50 DMS
Minimum Input
Altitude 0-4500 ft. (0-1372m)
21,000 Btu/h
(6.15 kW)
19,500 Btu/h
(5.71 kW)
Maximum Input
Altitude 0-4500 ft. (0-1372m)
39,000 Btu/h
(11.42 kW)
36,000 Btu/h
(10.54 kW)
Vent Sizing 5” Inner / 8” Outer 5” Inner / 8” Outer
71 1
4
"
1810 mm
11"
279 mm
18"
466 mm
10 1
4
"
260 mm
35 5
8
"
905 mm
72 5
16
"
1837 mm
35 5
8
"
905 mm
8"
204 mm
5"
127 mm
13"
330 mm
7 1
4
"
185 mm
20 5
16
"
515 mm
39"
990 mm
CB60E Dimensions - Bay Install

2 | City Series CB60E
CB60E Dimensions - (Corner Install)
71 1
4
"
1810 mm
11"
279 mm
18"
466 mm
10 1
4
"
263 mm
35 5
8
"
905 mm
72 5
16
"
1837 mm
35 5
8
"
905 mm
8"
204 mm
5"
127 mm
13"
330 mm
7 1
4
"
185 mm
20 5
16
"
515 mm
39"
990 mm
16 9
16
"
421 mm

City Series CB60E | 3
CLEARANCES CB60E (3-SIDED)
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance
that this fireplace and vent system be installed only in accordance with these instructions.
Flue Clearances to Combustibles
Horizontal - Top 3"
Horizontal - Side 2"
Horizontal - Bottom 2"
Vertical 2"
Passing through wall/
floor/ceiling - when
restop is used.
1-1/2"
Note: This appliance uses 5" x 8" venting.
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not adhered
to. It is of greatest importance that this fireplace and vent system be
installed only in accordance with these instructions.
The HeatWave Duct Kit has different
clearance and framing require-
ments, check the HeatWave manual
for details.
E
F
B
Alcove
Clearance: Dimension Measured From:
A1: Mantel Height (min.) ** Top of Fireplace Opening
A: From Floor (min.) 10-1/4" (260 mm) Bottom of Fireplace Opening
B: Sidewall (on one side) min. 5 7/8" (149 mm) Side of Fireplace Opening
C: Enclosure Width (min.) 71-1/4" (1810 mm) Minimum inside dimensions
D: Mantel Depth (max.) **
E: Alcove Width 119.5" (3035 mm) Sidewall to Sidewall (Minimum)
F: Alcove Depth 35" (889 mm) Front to Unit (Maximum)
G: Convection Air Outlet Opening Offset
(min.) 1" (25 mm) Max. offset from top of chase enclosure
H: Convection Air Outlet 180 square inches
I Enclosure Depth (min.) 20-5/16" (516 mm) Minimum inside dimensions
J: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening
K: To Ceiling (min.) all 3 sides 1-3/4" To Top of Ceiling
L: Chase Enclosure (min.) 81-1/4" (2064 mm) From base of unit/floor to top of enclosure
M:Clearance to Sprinkler Head (min.) 36" (914mm) Perpendicular from chase grill
Hearth 0" No hearth required
** See mantel clearances chart in the manual.
L
Chase grill
Sprinkler
Side view
M

4 | City Series CB60E
CLEARANCES CB60E (3-SIDED)
Floor to ceiling with top opening Full framing with vents in front/sides or top
Full framing with low vents in front or sides Full framing with vents in front or sides
C
I
A1
A
D
L
J
H
L
I
C
D
A1
A
J
G
G
H
H
H
I
C
G
A
A1
G
D
J
L
H
H
I
A
D
C
J
G
G
L
H
H
A1
opening opening
opening opening

City Series CB60E | 5
H
I
A
E
B
C
G
D
F
CLEARANCES CB60E (Corner Install)
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not adhered
to. It is of greatest importance that this fireplace and vent system be
installed only in accordance with these instructions.
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that
this fireplace and vent system be installed only in accordance with these instructions.
Note: Left handed corner shown in illustration. Clearances will be the same for the right hand side.
Clearance: Dimension Measured From:
A: Mantel Height (min.) ** Top of Fireplace Opening
B: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening
C: From Floor (min.) 10-1/4" (260 mm) Bottom of Fireplace Opening
D: Sidewall (on one side) min. 39" (991 mm) Side of Fireplace Opening
E: Mantel Depth (max.) ** Front of Fireplace Opening
F: Alcove Depth 35" (889 mm) Front of Fireplace Opening
G: Convection Air Outlet 180 square inches
H: Convection Air Outlet Opening Offset *1" (25 mm) Max. offset from top of chase enclosure
I: Chase Enclosure (Min.) 81-1/4" (2064 mm) From Base of Unit/Floor to top of enclosure
Hearth 0" No hearth required
** See mantel clearances chart in this manual.
Flue Clearances to Combustibles
Horizontal - Top 3"
Horizontal - Side 2"
Horizontal - Bottom 2"
Vertical 2"
Passing through wall/
floor/ceiling - when
firestop is used.
1-1/2"
Top View
Alcove
The HeatWave Duct Kit has different
clearance and framing require-
ments, check the HeatWave manual
for details.
D
F
Left Corner
Shown

6 | City Series CB60E
MANTEL CLEARANCES CB60E (3-SIDED)
Combustible mantel clearances from top of front facing
are shown in the diagram on the right.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:
212 6 4810
0
14
9”
18-1/16"
10
20
26
Top of
Fireplace
Opening
12" (305mm)
1/2" Drywall, wood, wood panel, etc.
5 1/4"
To Bottom of
Fireplace
Opening
12"
MANTEL LEG
0"

City Series CB60E | 7
FRAMING DIMENSIONS CB60E (3-SIDED)
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Framing
Dimensions Description CB60E
A Framing Height 41-1/4" (1 048 mm)
B Framing Width 71-1/4" (1810 mm)
C* Framing Depth 20-5/16" (516 mm)
D Minimum Height to Combustibles 81-1/4" (2038 mm)
G Vent Centerline Height 58-3/16" (1478 mm)
** Gas Connection Opening Height See gas connection location in this manual
** Gas Connection Height See gas connection location in this manual
** Gas Connection Inset-Centre Opening See gas connection location in this manual
* Not in diagram below
** See manual for alternate Gas/ Electrical connection options
Note: A combined minimum of
180 square inches of open area
is required for the convection air
outlet to cool the enclosure. En-
sure clearances for Convection Air
Outlets are met.
See clearances CB60E in this man-
ual as there are different methods
as to how this can be achieved.
Note: This appliance must be
installed on a solid surface
such as a plywood floor
which must be the full width
and depth of the appliance.
Ensure that the wood base that the appliance will sit on is strong enough to support the full weight of this appliance.
The overall weight of this appliance is 460 pounds (shipping weight).
Note: Unit must be installed onto a solid
backwall - do not install directly onto studs.
*C
Note : The framing depth does not take into
account drywall/wood or similar materials
against the back wall. The framing depth will
need to change based on the thickness of the
material (example: 20-5/16 framing depth +
1/2 drywall = 20 13/16")

8 | City Series CB60E
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Note: A combined minimum of 180
square inches of open area is required
for the convection air outlet to cool
the enclosure. Ensure clearances for
Convection Air Outlets are met.
See clearances CB60E in this manual
as there are different methods as to
how this can be achieved.
Note: This appliance must be in-
stalled on a level and solid surface
such as a plywood floor which must
be the full width and depth of the
appliance.
Framing
Dimensions Description Corner Kit
A Framing Height 41-1/4” (1048 mm)
B Framing Width 71-1/4" (1810 mm)
C Framing Depth 20-5/16" (516mm)
D Unit Base to Top Enclosure (Min.) 81-1/4"(2038 mm)
G Vent Centerline Height 58-3/16" (1478 mm)
NOTE: Unit cannot be load-bearing. All finishing materials must be supported by the framing.
Maximum material
dimensions 2" x 4" for
header studs (installed
on edge and flat)
Framing Dimensions Corner Kit - Corner Install
(Right Corner)

City Series CB60E | 9
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Note: A combined minimum of
180 square inches of open area
is required for the convection air
outlet to cool the enclosure.
Ensure clearances for
Convection Air Outlets are met.
See clearances CB60E in this
manual as there are different
methods as to how this can be
achieved.
NOTE: Unit cannot be load-bearing. All finishing materials must be supported by the framing.
Note: This appliance must be in-
stalled on a level and solid surface
such as a plywood floor which must
be the full width and depth of the
appliance.
Maximum material
dimensions 2" x 4" for
header studs (installed
on edge and flat)
Framing
Dimensions Description Corner Kit
A Framing Height 41-1/4” (1048 mm)
B Framing Width 71-1/4" (1810 mm)
C Framing Depth 20-5/16" (516mm)
D Unit Base to Top Enclosure (Min.) 81-1/4"(2038 mm)
G Vent Centerline Height 58-3/16" (1478 mm)
Framing Dimensions Corner Kit - Corner Install
(Left Corner)