Regulus Caleon User manual

www.regulus.eu
CALEON
CALEON
EN
Installation and Operation Manual
°CALEON WIFI ROOM UNIT

2
CONTENTS
CONTENTS.................................................................................................................................................................................2
SAFETY INSTRUCTIONS...........................................................................................................................................................3
Declaration....................................................................................................................................................................................... 3
General Instructions........................................................................................................................................................................ 3
Changes to the Unit......................................................................................................................................................................... 3
Warranty and Liability ....................................................................................................................................................................... 3
Disposal of the Unit .......................................................................................................................................................................... 4
DESCRIPTION OF °CALEON ROOM UNIT.................................................................................................................................5
Specifications ................................................................................................................................................................................... 5
Scope of Supply .............................................................................................................................................................................. 5
IINSTALLATION...........................................................................................................................................................................6
°CALEON Installation........................................................................................................................................................................ 6
Example of Controller Connection .................................................................................................................................................... 8
OPERATION.................................................................................................................................................................................9
Overview of Temperatures & Humidity............................................................................................................................................. 9
Operating Mode Selection ................................................................................................................................................................ 9
Main Menu......................................................................................................................................................................................... 9
Expert Menu.................................................................................................................................................................................... 10
Expert Menu °CALEON................................................................................................................................................................... 10
Set Operation Hours ....................................................................................................................................................................... 10
Setting Operation Hours................................................................................................................................................................... 11
NOTES ....................................................................................................................................................................................... 12
WiFi settings..................................................................................................................................................................................... 11

3
SAFETY INSTRUCTIONS
Declaration
By affixing the CE mark to the unit the manufacturer declares that °CALEON unit conforms to the following relevant safety regulations:
•EU low voltage directive 2014/35/EU
•EU electromagnetic compatibility directive 2014/30/EU
Conformity has been verified and the corresponding documentation and the EU declaration of conformity are kept on file by the
manufacturer.
General instructions
Please read carefully!
These installation and operating instructions contain basic instructions and important information regarding safety, installation,
commissioning, maintenance and the optimal use of the unit. Therefore these instructions must be read and understood
completely by the installation technician/specialist and by the system user before installation, commissioning and operation of
the unit. Installation, electrical connection, commissioning and maintenance of the unit may only be carried out by specialists
who possess the appropriate training.
Users: Make sure that the specialist gives you detailed information on the function and operation of the unit. Always keep these
instructions in the vicinity of the unit. Changes to the unit may compromise safety and functioning of the unit and entire heating
system.
Changes to the Unit
•Changes, additions to or conversion of the unit are not permitted without written permission from the manufacturer.
•It is likewise forbidden to install additional components that have not been tested together with the unit.
•If it becomes clear that safe operation of the unit is no longer possible, for example because of damage to the housing,
turn the Unit off immediately.
•Any parts of the unit or accessories that are not in perfect condition must be exchanged immediately.
•Use only original spare parts and accessories from the manufacturer.
•Markings made on the unit at the factory must not be altered, removed or made illegible.
•Only the settings described in these instructions may be set using the Unit.
Changes to the unit can compromise the safety and function of the unit or the entire system.
Warranty and Liability
The Unit has been manufactured and tested with regard to high quality and safety requirements. The warranty and liability shall
not include, however, any injury to persons or material damage that is attributable to one or more of the following causes:

4
•Failure to observe these installation and operating instructions.
•Improper installation, commissioning, maintenance and operation.
•Improperly executed repairs.
•Unauthorized structural changes to the unit.
•Additional components have been installed into the Unit that have not been tested with it.
•Damage caused by continuing to use the Unit despite an obvious defect.
•Use of non-OEM spare parts
•Use of the device for other than its intended purpose.
•Operation above or below the limit values listed in the Specifications section.
•Force majeure
Disposal of the Unit
The unit conforms to the European RoHS 2011/65/EU for the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
Under no circumstances may the device be disposed of with the normal household waste. Dispose of the unit
only at appropriate collection points or ship it back to the seller or manufacturer.

5
DESCRIPTION OF °CALEON ROOM UNIT
Specifications
2-part, ABS plastic
75 mm x 95 mm x 19 mm
Glass front
Capacitive touch screen Colour
display with 240x320 dots
7 cm diagonal
Intuitive user guidance
Deutsch English
Español Italiano
Français Português
Electrical Data:
Power supply
Power consumption
IP rating
Protection class / overvoltage category
Max. cable length
CAN
Permissible Ambient Conditions
during operation
for transport/storage
Measuring range Internal
temperature sensor
Internal humidity sensor
Accuracy +/- 1 °C
Resolution 0,1 °C
Accuracy +/- 6 %
Resolution 0,1 %
Other Specifications
Installation methods
Real Time Clock
12 - 24 VDC +/- 10%
0,5 W - 1,0 W
IP20
III / II
Up to 3m an unshielded pair bus cable can be used. If the cable length is over 3m,
it is necessary to use a shielded twisted pair bus cable and connect the shield on
one side to the protective conductor.
0°C - 50 °C, no moisture condensation permitted
0°C - 60 °C, no moisture condensation permitted
Outside the measuring ranges there are larger deviations
0°C - 60 °C
0 % - 100 % RH
Wall installation, with/without wall socket
RTC with 24 hour power reserve
Scope of Supply
•°CALEON Room Unit
•2 screws 3,5 x 35 mm and 2 plugs 6 mm for wall installation
•2 single conductor connectors, CAN connector with connecting cables, terminating resistor CAN connector,
terminating resistor °CALEON, operating tool
•°CALEON installation guide

6
INSTALLATION
°CALEON Installation
Mount the unit at a suitable location.
Pay attention to suitable environmental conditions. Direct sunlight,
sources of heat and cold, e.g. radiators and windows must be
avoided.
Strip cables, slip protective conductor over, and remove fill material as
needed.
When mounting °CALEON's base to the wall the connecting cables must be
kept as short as possible. For direct wall mounting a maximum length of 40
mm is recommended. Long wire loops inside the °CALEON's housing may
cause problems.
When mounting °CALEON's base to a plastic wall socket the connecting
cables must be kept as short as possible (strip cables not more than 55 mm).
Also make sure that wire loops are led back to the plastic wall socket, since
long wire loops inside the °CALEON's housing may cause problems.
Strip the last 8-9 mm of the wires. Isolate shielding and connect it at a
suitable location (controller or CAN-box) to the protective conductor.
Any contact between protective conductor and circuit board can
cause serious damage.
Strip cables by 75 mm max. and strip the last 7-10 mm of the wires.

7
Mounting on plastic wall socket
Fix the base with the screws (3.0 x 16) to the mounting box.
Direct wall mounting
Hold the lower part of the housing up to the selected position and mark
the mounting holes. Make sure that the wall surface is as even as
possible so that the housing does not become distorted when screwed
on. Using a 6mm drill, drill 2 holes at the points marked on the wall and
push in the plugs. Insert screws and screw it in slightly. Align the base
and tighten the screws.
Open the terminals with the enclosed operating tool and connect the
electric as described.
Power supply 12 - 24 VDC, ensure correct polarity or it
may cause damage to the unit!
The first and last unit in the CAN-network in series must be
fitted with terminating resistance.
The connection of the opposite side (controller) can be found in
the corresponding terminal diagram in the controller manual.
Refit the base and fasten with screw. Switch on mains voltage
and place °CALEON in operation.
in the °CALEON menu under Expert at any time.

8
Example of Controller Connection
Terminating resistor, if only 1 °Caleon is
isntalled.
Max. number of °Caleon Room Units to be
connected to a Controller without an auxiliary
12-24VDC power source is 2.
External 12-24VDC power supply
Terminating resistor, if the last device in the
series.
Use a four-core cable to electrically connect the Caleon room unit to TRS controllers. If the cable length is more than 3 meters,
use a twisted shielded cable and connect the shield at one end of the cable. If the cable length is less than 3 meters, it is possible
to use a non-twisted unshielded cable. Connect the CAN power and communication as shown in fig. below.
Alternatively, it is possible to connect the CAN communication between the Caleon room unit and the TRS controller via
a two-core cable. The power supply of the room unit must then be solved by an external 24VDC power supply.
The CAN bus terminating resistor may be connected just to one end of the communication line (either to the controller or to the last
unit in the series - see figure below). The resistor included with the Caleon unit is designed for connection to a connector on the
controller's printed circuit board.

9
OPERATION
Overview of temperatures & humidity
It displays room temperature and humidity as well as
outside temperature. If there is no activity for 60 sec.,
the device is automatically switched to the overview.
Operating Mode Selection
This indicates the temperature of the selected space
in 0.1 degree increments.
Room humidity
Here the relative humidity of
the selected space in 0.1 %
increments is displayed.
Outdoor temperature
This is the outdoor
temperature in 0.5 degree
increments, measured by
TRS controllers.
Operating Mode Selection
Back
navigates back to the overview.
Location/Room
displays the selected location/
room.
Minus/Plus
changes the desired
temperature +/- 0.5 ° C.
Operating modes
navigates to the main menu.
Operating modes
specifies which operating mode (Normal, Comfort, Eco
and Off) is selected. The selected mode is shown in
colour. By pressing the plus and minus keys it is
possible to adjust the setpoint temperature of the
modes.
Main Menu
Overview > Operating Mode > Main Menu
Periods
Adjustment of individual heating times for
each weekday with copy function for
subsequent days.
Holiday
Set time and temperature for the
period of absence.
Expert
Standard settings such as language,
time and date, functional options and
factory setting.
Periods Holiday
Expert

10
Expert Menu
Overview > Operating Mode > Main Menu > Expert
Language
The configuration of the device language.
Time & Date
The configuration of the time and date and automatic
summer/winter changeover.
Caleon
Settings concerning basic functions such as sensor
calibration, location and commissioning.
Network
Information on device version as
well as the CAN ID for the device
on the network.
Factory Settings
The factory settings are restored in
the device.
Expert Menu °CALEON
Overview > Operating Mode > Main Menu > Expert > Settings
Devices
Used to adapt the offset for the said local
sensors, display brightness etc.
Rooms
In this menu you specify in which room
°CALEON is installed.
Functions
In this menu all the available functions of
the connected controller can be set.
WiFi
Here the features of the wireless WiFi network
are set and managed.
Interface mode
Setting the unit type – normal (full functions) or
simple (basic display).
To exit the simple display mode, press and
hold the top right corner of the display for at
least 5 seconds.
Set Operation Hours
Overview > Operating Mode > Main Menu > Timer
Operating modes
Selects the operating mode to
individual heating sections.
Previous/Next Day
Selects the set day.
Clock
Time table of the selection in periods of 30 minutes
increments.
Menu
Opens the copy function. This function allows you to
copy the heating times for the next day, on Monday-
Friday or Monday-Sunday.
Friday

11
Setting Operation Hours
Step 1
Use the arrow keys to select the desired day.
Step 2
Select the first heating mode
(Regular) - with the index
finger select the desired
length of time. The selected
period is coloured by selecting
Step 3
Continue to the next mode
(Comfort) and proceed as
described above, select the
time period for the Comfort
Mode.
Step 4
Continue to the next mode
(Eco) and proceed as
described above, select the
time period for the Eco Mode.
Step 5
Continue to the next mode
(Off) and proceed as
described above, select the
time period for the Off Mode.
the colour of the operating
mode (regular = orange).
Step 6
After the completion of the setting of the individual heating times, you have the option of selecting times using the main
menu for the next day, or to copy Monday-Friday or Monday-Sunday.
WiFi Settings
Overview > Operating Mode > Main Menu > Expert > WiFi
Access control
Allow access through Caleon App.
You can fill in up to 5 e-mail addresses that will
have a permission for remote access to the
room unit.
SSID
The possibility of manually connecting to a WiFi
network by entering its name (for example, if
the network does not actively broadcast its
name, is hidden).
Enable WiFi
Activates connection to wireless network
WiFi status
Network and signal status, address
information for the Caleon room unit
(required to connect to the Caleon App).
Choose Network
Search for all available wireless networks
within range.

©2020 We reserve the right to errors, changes and improvements without prior notice.
REGULUS spol. s r.o.
E-mail: [e-mail]
Web: www.regulus.eu
v1.0-02/2020
Password
Enter the password to connect to the wireless network.
Enable DHCP
Activation of network IP address retrieval by DHCP server
(recommended). If DHCP is not activated or the DHCP
server is not in the network, it is necessary to fill in the IP
addresses manually.
IP address
Room unit IP address.
Subnet mask
Network space mask of the
wireless network
Gateway
Gateway (router) IP address.
DNS/DNS 2
DNS server addresses
(primary / secondary).
Downloading and configuring Caleon App
1. Download the Caleon App to your mobile device. The app is available for
Android (Google Play) and iOS (Apple App Store).
2. Launch the application and create a user account.
3. Confirm your email address by clicking the link in the activation email.
4. Connect the room unit to the WiFi network
in Expert > WiFi > Choose network .
5. Enable remote access from your email address in the
Expert > WiFi> Access Control menu.
6. Log in to the Caleon App using your email address and password.
7. In the Caleon App, fill in the network address of your room unit (you can
find the address in Expert > WiFi> Wifi Status).