Reliable Equipment & Service REL-58RH Manual
1
DISTRIBUTED BDISTRIBUTED B
DISTRIBUTED BDISTRIBUTED B
DISTRIBUTED BYY
YY
Y
OPERAOPERA
OPERAOPERA
OPERATORS’TORS’
TORS’TORS’
TORS’
GUIDEGUIDE
GUIDEGUIDE
GUIDE
REL-58MC Manual 03-07
RELIABLE EQUIPMENT & SERVICE CO., INC.
301 Ivyland Road • Warminster, PA 18974 • USA
Phone: 215-357-3500 • Fax: 215-357-9193
MODEL: __________________________________
MAX. PRESSURE: _________________________
SERIAL NO.: ______________________________
YEAR: ___________________________________
NOTICENOTICE
NOTICENOTICE
NOTICE
Sizes, weights and tool
specifications listed in
this manual are subject
to change without notice.
Please consult factory for
information and updates.
WARNINGWARNING
WARNINGWARNING
WARNING
All information found in this guide
must be read and understood before
use or testing of this tool.
Failure to read and understand these warnings
and safe handling instructions could result
in severe personal injury and or death.
6 TONS OF CUTTING FORCE
REL-58RH
SINGLE ACTING HYDRAULIC
CUTTING TOOL
2
REGISTRATION
UPON RECEIPT OF THIS TOOL, COMPLETE THE REGISTRATION BELOW.
COMPANY ___________________________________________________________
ADDRESS ____________________________________________________________
______________________________________________________________________
PHONE ______________________ FAX __________________________________
SERIAL NUMBER ____________________________________________________
DATE OF PURCHASE ________________________________________________
DEALER NAME _______________________________________________________
CAUTION
The information in this manual is intended to guide the user in
the use and application of this tool. It is not intended as a
substitute for proper training and experience in safe work
practices for this type of equipment.
Consult your supervisor or safety personnel if you have any
questions regarding the safe operation of this tool.
DISTRIBUTED BDISTRIBUTED B
DISTRIBUTED BDISTRIBUTED B
DISTRIBUTED BYY
YY
Y
3
TABLE OF CONTENTS
THIS SYMBOL INDICATES ITEMS OF EXTREME IMPORTANCE.
Safety of user and others may be in jeopardy if these instructions
are not read and understood.
DISTRIBUTOR INFORMATION............................................................ 2
REGISTRATION .................................................................................... 2
TABLE OF CONTENTS......................................................................... 3
TOOL SPECIFICATIONS
REL-58RH - S/A REMOTE HYD. CUTTING TOOL ............. 4
SAFETY INFORMATION AND WARNINGS.................................... 5-9
OPERATING INSTRUCTIONS ........................................................... 10
MAINTENANCE................................................................................... 11
GENERAL MAINTENANCE ................................................................ 11
PARTS DIAGRAM 1 ............................................................................ 12
PARTS DIAGRAM 2 (HEAD ASSEMBLY, EXPLODED VIEW) ........ 12
PARTS LIST ......................................................................................... 13
MAINTENANCE RECORDS ............................................................... 14
CONTACT INFORMATION ................................................................. 14
If you have any questions regarding the information
found in this manual please contact RELIABLE EQUIPMENT
at 800-966-3530 or FAX 215-357-9193.
4
SPECIFICATIONS
Length 6.75 inch
Weight 4.0 lbs.
Pressure 10,000 psi
Wire Ropes 1 inch
Soft Steel Bolts 7/8 inch
Rebar, Ground 5/8 inch
& Anchor Rod
Cu. & Al. Wire 1 inch
ACSR 1 inch
Stand. Guy Wire 7/8 inch
Lead Sheathed & DO NOT CUT
Telephone Cable
REL-58RH
SINGLE ACTING HYDRAULIC
CUTTING TOOL
REL-58RH -SINGLE ACTING
HYDRAULIC CUTTING TOOL
Among the smallest hydraulic cutting
tools available. Designed to cut copper,
aldrey, aluminum, aluminum-steel
cables, EHS guy wire and steel ropes
having a max overall diameter of 1” and
steel ground rod up to 5/8”. The blades
are manufactured from high strength
special steel, heat treated to ensure a
long service life.
The head will rotate by 180 degrees.
Enabling the operator to work in the
most comfortable position, reducing
fatigue. The REL-58RH positive latch
head opens easily to allow fast tool
relocation, and simplify the cutting of
running cables.
301 Ivyland Road • Warminster, PA 18974
Phone: 800-966-3530 • Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
6 TONS OF CUTTING FORCE
5
WARNING
BEFORE USING THIS TOOL, READ THE WARNINGS
and the recommended practices described in this manual.
Failure by the operator to read and fully understand these
warnings will leave this person unqualified to use and
operate this tool. Property damage, severe personal injury,
and/or death could result by not following these warnings.
Eye
Protection
These warnings will appear in appropriate locations when they are pertinent to the
particular subject being shown. Read each one carefully and follow them strictly.
WARNING
Always wear eye protection to avoid
injury from flying debris or hydraulic
oil leaks. Failure to do so can result
in serious personal injury.
Hard Hat
WARNING
Always wear a hard hat to avoid injury
from falling debris. Failure to do so
can result in serious personal injury.
Hearing
Protection
WARNING
Always wear hearing protection,
to avoid hearing loss due to long
term exposure to high noise levels.
Foot
Protection
WARNING
Always wear foot protection.
Failure to do so can result in serious
personal injury.
Skin
Irritation
WARNING
WARNING
Protective
Gloves
Always wear protective gloves
Failure to do so can result in serious
personal injury.
Hydraulic oil may cause irritation.
Use care to prevent contact with skin.
In case of accidental contact, wash
affected area immediately
6
WARNING
HYDRAULIC POWER SUPPLY
DO NOT attempt to make any changes to any of the component
parts or accessories when connected to the power source.
DO NOT adjust, inspect, or clean tool while the tool is connected
to the power source. The tool could accidentally start up
and cause serious injury.
DO NOT lock the tool in the On Position. In an emergency,
serious damage or injury could occur during the time
required to stop the tool.
SAFE OPERATION & CARE
USE THIS TOOL FOR ITS INTENDED PURPOSE ONLY
Any other use can result in personal injury or property damage.
INSPECT TOOL BEFORE USE. Replace any worn, damaged or
missing parts. A damaged or improperly assembled tool may
malfunction, injuring operator and/or nearby personnel.
INSPECT HYDRAULIC HOSES AND COUPLINGS before each
use. Repair or replace if any cracking, leakage, wear or damage
is found. Worn or damaged hoses may fail resulting in personal
injury or property damage.
CLEAR WORK AREA of all bystanders and unnecessary
personnel before operating this tool.
KEEP ALL PARTS OF THE BODY AWAY FROM MOVING PARTS.
Failure to observe this warning could result in serious injury.
WARNING
TOOL HAZARD
DO NOT EXCEED THE MAXIMUM HYDRAULIC FLOW,
RELIEF PRESSURE, OR BACK PRESSURE.
Failure to observe warnings could result in tool damage or injury.
WARNING
IF YOU HAVE ANY QUESTIONS REGARDING THE SAFE USE
AND/OR OPERATION OF THIS TOOL, CONSULT YOUR AREA SUPERVISOR,
OR CONTACT RELIABLE EQUIPMENT AT 800-966-3530
7
HOSES AND FITTINGS
There exists the potential for shock in using anything other
than certified nonconductive hoses and hydraulic oil with
dielectric properties, when using system components near
energized electrical lines. Failure to recognize these conditions
could cause electrocution.
Hoses and fittings used with this tool must comply with S.A.E. J1273 which covers
recommended practice for selection, installation, and maintenance of hose and hose
assemblies. The correct hoses and fittings are available from your supplier.
WARNING: Failure to comply with these warnings could result in severe bodily injury.
WARNING
UNIT/HOSE CONNECTIONS
ALWAYS DISCONNECT pump/power source and move toggle
switch to OFF before connecting or disconnecting any components.
ALWAYS DEPRESSURIZE hydraulic system, before slowly
disconnecting this unit or any of the systems components.
ALWAYS TIGHTEN couplings completely. Loose or improperly
tightened couplings will not allow fluid to pass through the
hose creating a blockage in the supply or return line.
ALWAYS INSPECT HOSES AND CONNECTORS before
connection to tool. Replace or repair if any leakage is evident.
Leakage is a sign of deterioration in component parts. Worn
or leaking parts must be repaired or replaced, or tool damage
or severe injury could result.
WARNING
WARNING
OIL INJECTION INJURY
Hydraulic oil or fluid under the skin is a serious injury. Oil
under pressure can penetrate the skin and may cause
dismemberment or loss of life. Seek medical assistance
immediately if such an injury should occur.
Always wear safety gloves, eye protection and all required
safety equipment when operating or handling this tool.
DO NOT use fingers or hands to attempt to locate a leak.
DO NOT handle hoses or couplers while system is pressurized.
NEVER open or service the system before depressurizing.
8
WARNING
WARNING
ELECTRICAL SHOCK HAZARD
Always wear and use the necessary clothing, equipment
and safety practices to protect against electrical shock.
Failure to follow these rules can result in serious personal
injury or death.
Operation/Safety methods may vary in accordance
with the working guidelines established by each utility
or contractor.
For your own safety, ensure that you fully comply with
all safe operation guidelines required by your employer.
SERIOUS BURN HAZARD
HOT SURFACES MAY CAUSE SERIOUS BURN OR INJURY
The hydraulic cylinder may be hot during and after operation.
CACA
CACA
CAUTIONUTION
UTIONUTION
UTION::
::
:HYDRAULIC FLUID MAY CAUSE SERIOUS BURNS
Never disconnect tool, hoses, or fittings while the hydraulic
power source is running or if the hydraulic fluid is hot.
Failure to observe this warning could result in serious injury.
WARNING
WARNING
CUTTING DANGER
This hydraulic cutting tool can cut, dismember and/or disable.
KEEP ALL PARTS OF THE BODY AWAY FROM MOVING PARTS.
DO NOT lock the tool in the On Position. In an emergency,
serious damage or injury could occur during the time required
to stop the tool.
Failure to observe this warning could result in serious injury
.
IF YOU HAVE ANY QUESTIONS REGARDING THE SAFE USE
AND/OR OPERATION OF THIS TOOL, CONSULT YOUR AREA SUPERVISOR,
OR CONTACT RELIABLE EQUIPMENT AT 800-966-3530
9
GENERAL SAFETYGENERAL SAFETY
GENERAL SAFETYGENERAL SAFETY
GENERAL SAFETY
FAILURE TO HEED THESE WARNINGS COULD RESULT IN
PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR DEATH.
USE ALL APPROPRIATE AND APPLICABLE PERSONAL SAFETY EQUIPMENT
as required by the operating company.
INSPECT TOOL BEFORE USE. Replace any worn, damaged or missing parts. A damaged
or improperly assembled tool may injure operator and/or nearby personnel.
KEEP ALL PARTS OF THE BODY AWAY from moving parts of the tool.
KEEP HANDS OUT FROM BETWEEN CUTTING BLADES AT TOOL HEAD.
ALL BODY PARTS SHOULD BE OUTSIDE DANGER ZONE PRIOR TO CUTTING.
MAKE SURE there is no person in close proximity to you or the tool who could be
injured by any operation being performed, tool malfunction or flying debris.
DO NOT OVEREXTEND your position by overreaching or unbalancing the footing
necessary to maintain physical control of your body and the tool.
ALWAYS MAINTAIN a firm grip on the tool to avoid loss of control during an operation,
causing property damage, serious injury or death.
USE THIS TOOL FOR THE MANUFACTURERS’ INTENDED PURPOSE ONLY.
OBSERVE CLOSELY ALL OF THE SAFETY RULES FOR A PARTICULAR JOB CLASS
Operation/Safety methods may vary in accordance with the working guidelines
established by each utility or contractor. Ensure that you fully comply with all safe
operation guidelines required by your employer.
10
OPERAOPERA
OPERAOPERA
OPERATIONTION
TIONTION
TION
Read entire manual prior to using this tool. Refer to all safety cautions and warnings.
Observe all safety precautions and procedures required by the operating company.
(Also refer to SAFETY information found on pages 6 through 10)
1. Before cutting, ensure that subject is within the capacity listed for the tool. (see page 5)
2. Connect to a 10,000 psi power source with an audible “Pop Off” type relief valve.
(Recommended for best operation) (Refer to page 8 UNIT/HOSE CONNECTION)
2. Ensure movable blade has retracted completely.
3. Release latch (B), and open tool head for simple tool positioning around subject to be cut.
NOTE: Tool head rotates 180O to aid in proper alignment.
4. Place subject in tool head (C) and close latch securely.
WARNING: Failure to secure latch may result in severe tool damage and/or personal injury.
5. Position subject at a 90O angle to the tool head and cutting blade.
NOTE: Failure to cut subect at the proper 90O angle may result in
severe tool damage and/or personal injury.
7. Turn power source “ON” and activate control valve to advance movable blade
up to subject. Check tool alignment.
8. Continue to advance until cut is complete.
9.Return source to the “OFF” position and allow movable blade to retract completely.
B LATCHC CUTTING HEAD DHEAD ROTATES
180O FOR EASY
POSITIONING
10,000 PSI COUPLERMOVABLE BLADE
Do not cut live conductors.
Hardened metals may fly when severed.
Take necessary precautions. waer safety glasses.
Keep all body parts away from cutting blades and moving parts.
WARNING
Failure to follow these rules can result in serious personal injury or death.
11
Complete disassembly is not recommended. Return the unit to an authorized dealer
for total disassembly and/or repair.
All maintenance or disassembly should take place on a flat, clean work surface covered
with towels or wipers so as to have a clean space for the disassembled parts.
Inspect each part during disassembly for wear, scratches, and cuts. Discard the worn or
damaged parts and replace with new factory authorized parts. See parts drawings on pg16-20.
O-rings are sensitive to sharp edges. Inspect closely for cuts or damage. A small cut
will cause a leak. When assembling or disassembling O-rings, use hydraulic fluid as a
lubricant to help disassembly or installation.
When disposing of hydraulic parts or components observe all federal, state, and local guidelines.
IF YOU HAVE QUESTIONS REGARDING THE REPAIR AND MAINTENANCE
OF THIS TOOL CONTACT RELIABLE EQUIPMENT AT 800-966-3530
GENERAL MAINTENANCEGENERAL MAINTENANCE
GENERAL MAINTENANCEGENERAL MAINTENANCE
GENERAL MAINTENANCE
DAILY MAINTENANCE
The life, reliability, and safety of the tool is dependent on proper maintenance.
Clean and inspect all surfaces including head, latch mechanism, blade, ram, and body.
WARNING blade, head may cut or pinch. Please use extreme caution.
Worn or damaged parts (i.e. chipped or cracked blade) may malfunction during operation,
causing more extensive damge to the tool and/or severe injury to the operator or bystander..
All parts must be replaced with new parts if signs of wear or damage are evident.
Keep Label Set clean and legible. Replace decals when necessary.
BEFORE USING THIS PRODUCT
READ THE SAFETY WARNINGS
and recommended practices described
in the manual. Failure by the operator to
read and fully understand the warnings
will leave this person unqualified to use
and operate the tool.
Failure to observe all warnings and instructions could result
in property damage, severe personal injury, and/or death.
ELECTROCUTION
HAZARD
The user should be properly
trained in the correct procedures
required for work on or around
electrical lines.
REL-SM
WARNING
Hardened metals may fly when
severed. Take necessary precautions.
waer safety glasses do not cut live
conductors. Keep fingers away
from cutting blades and moving parts.
Secure latch before operating.
Failure to secure latch can result in
severe tool damage and personal injury.
12
14
13 2
18
19
3
4
5
17
16
15
EXPLODED HEAD
DIAGRAM 2
DIAGRAM 1
REL-58RH
SINGLE ACTING HYDRAULIC
CUTTING TOOL
13
ITEM PART QTY DESCRIPTION
1 R36002 1 HEAD SUPPORT
2 R36011 1 LATCH
3 R36003 1 CUTTER HEAD
4 R36004 1 SPACER, CUTTER HEAD
5 R36005 1 SUPPORT, CUTTER HEAD
6 R36010 1 GUIDE RING
7 R36009 1 SPRING
8 R43102 1 RAM
9 R36049 1BACK-UP RING
10 R36048 1O-RING
11 R43501 1 CYLINDER
12 --------- -- ---------------
13 R36013 2 PIVOT PIN (HEAD ASSEMBLY)
14 R36014 4 BOLT
15 R36015 4NUT
16 R36016 4WASHER
17 R36017 2 C-CLIP (HEAD PIVOT PINS)
18 R36057 1 SLIDE PIN (FOR LATCH)
19 R36012 1SPRING (LATCH)
20 R36006 1 CUTTER BLADE
21 R36007 1 SCREW, BLADE HOLDER
REL-58RH - PARTS LIST
14
Date Parts or Service Required
MAINTENANCE RECORDSMAINTENANCE RECORDS
MAINTENANCE RECORDSMAINTENANCE RECORDS
MAINTENANCE RECORDS
301 Ivyland Road Warminster, PA 18974
Phone: 800-966-3530 Fax: 215-357-9193
Visit us on the web at www.Reliable-Equip.com
If you have any questions regarding the information
found in this manual please contact RELIABLE EQUIPMENT at the
address, phone or fax numbers shown below.
Table of contents
Other Reliable Equipment & Service Cutter manuals
