Remington Flexibrush Steam CB4N User manual

CB4N
Flexibrush Steam
090168 REM IFU CB4N_UK.indd 1
26.03.09 19:24

Flexibrush Steam
A
B
C
D
E
F
G
H
E
C
A
CB4N_INT_IFU_17_01_08 18.03.2008 21:32 Seite 2
Flexibrush Steam
090168 REM IFU CB4N_UK.indd 2
26.03.09 19:24

Thank you for buying your new Remington®product. Before use, please read these
instructions carefully and keep them in a safe place for future reference.
PRODUCT FEATURES
AReservoir: Unscrew and fill with water, then press to activate steam
bBristle Lock Guard: When removed enables bristles to be slid on or off barrel.
When in place it acts as a guard and locks bristles into place
cHeat Resistant Bristles: Two sets of soft, removable bristles that remain cool to touch
dOn indicator light
eCurl Release: Depressing the button allows free rotation of the barrel
fHeel Rest: Prevents any part of the heated barrel from touching surface area when
resting
gSwivel Cord
h
Multivoltage: For use at home or abroad
The unit will automatically convert from 220/240v to 120 volts
2 year guarantee
INSTRUCTIONS FOR USE
Before use make sure hair is clean, dry and tangle free.
Remington Flexibrush can be used without steam. When steam is required first fill the water
reservoir.
Hold the unit in a vertical position with cap end down to prevent any spillage from any residual
water left in the cap.
Unscrew the reservoir and fill with warm or cool water to the fill line. Replace the cap with
the tong still held vertically with cap end down and twist gently into place.
Plug the unit into the mains and wait for about 5 minutes.
To activate steam, gently depress the cap. The unit is designed to release with one push, just
the right amount of steam required for a small section of hair.
Separate the section of hair to be curled and wrap around the hot barrel, winding up exactly
as you would use a roller.
Press reservoir cap to release the steam. Hold the Flexibrush in place for about 8-12 seconds
– then press the curl release button and carefully draw the unit away allowing hair to unwind
automatically. Let curls spring back and cool before combing.
To change the bristles, the unit must be unplugged and cool. Unscrew the Bristle Lock Guard
(B) and slide the bristles off the barrel. Taking the other set of bristles, gently glide each row
into a groove on the barrel and push into place. Screw the lock guard securely back into place.
1
ENGLISH
120 - 240V
MULTI VOLTAGE
Flexibrush Steam
A
B
C
D
E
F
G
H
E
C
A
CB4N_INT_IFU_17_01_08 18.03.2008 21:32 Seite 2
090168 REM IFU CB4N_UK.indd 1
26.03.09 19:24

ENGLISH
2
IMPORTANT INSTRUCTIONS
Due to the extreme heat capabilities of this styler, extra care should be taken when
using.
While heating and cooling, place on flat, smooth, heat-resistant surface. Only hold unit
at the end of the handle.
Please note regular use of styling products may deteriorate the coating.
Do not scratch the surface, as this will deteriorate the effectiveness of the coating.
Do not allow water from the reservoir cap to spill onto the handle.
CLEANING AND MAINTENANCE
Ensure the unit is unplugged and cool. Wipe clean any build up of styling products with a
damp cloth. Do not use an abrasive cleaning fluid to clean, as damage will occur.
SAFETY CAUTIONS
WARNING – FOR ADDITIONAL PROTECTION THE INSTALLATION
OF A RESIDUAL CURRENT DEVICE (RCD) WITH A RATEDRESIDUAL
OPERATING CURRENT NOT EXCEEDING 30mA IS ADVISABLE. ASK AN
ELECTRICIAN FOR ADVICE.
WARNING – THIS APPLIANCE MUST NOT BE TAKEN INTOA BATHROOM.
IT SHOULD NOT BE USEDNEAR BATHTUBS, SHOWERS, BASINS OR
OTHER VESSELS CONTAINING WATER OR OTHER LIQUIDS.
This product is not suitable for use in bath or shower.
THE STYLER SHOULD BE UNPLUGGEDFROM MAINS SUPPLY WHEN
NOT IN USE
Do not leave the styler unattended when switched on.
Allow the styler to cool down before storage.
Do not immerse in water or other liquids.
Do not place styler on soft material e.g. carpet, bedding, towels, rugs etc.
Keep this product out of reach of children. The use of this appliance by persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
can give cause to hazards. Persons responsible for their safety should give explicit
instructions or supervise the use of the appliance.
090168 REM IFU CB4N_UK.indd 2
26.03.09 19:24

ENGLISH
3
Do not use any attachments with this styler, other than those supplied by Remington®.
Do not wrap the cord around the unit. Check cord regularly for any sign of damage.
This product is not intended for commercial or salon use.
Damaged cords can be dangerous. If the supply cord of this unit becomes damaged,
discontinue use immediately and return the appliance to your nearest authorised
Remington®service dealer for repair or replacement in order to avoid a hazard.
Special tools are required for any examination, adjustment or repair. Unqualified repair
work could lead to hazardous conditions for the user.
We do not accept responsibility for damage to the product, persons or other items(s),
caused by misuse, abuse or non-compliance with these instructions.
WIRING INSTRUCTIONS UK Plugs Only
This product is fitted with a BS1363 plug fused at 13A. If the plug is unsuitable, it should be
disconnected and an appropriate plug fitted as detailed below. If it is necessary to replace
the plug fuse, use only fuses that are approved to BS1362, rated at 5A. If in doubt consult a
qualified electrician.
The wires in the mains lead are coloured in accordance with following code:
BLUE – NEUTRAL
BROWN – LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:-
The wire which is coloured BLUE must be connected to the terminal which is marked
‘N’ or coloured BLACK. The wire which is coloured BROWN must be connected to the
terminal which is marked ‘L’ or coloured RED. Never connect either of the wires to the big
EARTH terminal marked ‘E’ or coloured GREEN or GREEN AND YELLOW.
SERVICE ANDWARRANTY
This product has been checked and is free of defects. We warrant this product against any
defects that are due to faulty material or workmanship for the warranty period from the
original date of consumer purchase. If the product should become defective within the
warranty period, we will repair any such defect or elect to replace the product or any part
of it without charge provided there is proof of purchase. This does not mean an extension
of the warranty period.
In the case of a warranty simply call the Remington®Service Center in your region.
This warranty is offered over and above your normal statutory rights.
E
L
N
NEW WIRING
COLOUR CODE
BLUE
TO NEUTRAL
BROWN
TO LIVE
090168 REM IFU CB4N_UK.indd 3
26.03.09 19:24