Renogy RNGBTCM001 User manual

RENOGY
RNGBTCM001 Bluetooth communication Module
User Manual
16 Jun. 2023
Version: V1.0

Applicability
The User Manual applies to the following product:
Bluetooth communication Module RNGBTCM001
Disclaimer
Renogy makes no warranty as to the accuracy, sufficiency, or suitability of
information in the User Manual because continuous product improvements are
going to be made.
Renogy assumes no responsibility or liability for losses or damages, whether
direct, indirect, consequential, or incidental, which might arise out of the use of
information in the User Manual.
Renogy is not responsible or liable for the failures, damages, or injuries resulting
from repair attempted by unqualified personnel or improper installation and
operation.
The illustrations in the User Manual are for demonstration purposes only.
Details may appear slightly different depending on product revision and market
region.
Renogy reserves the right to change the information in the User Manual without
notice.
Copyright
Bluetooth communication Module User Manual © 2023 Renogy.
All rights reserved.
All information in the User Manual is subject to copyright and other intellectual
property rights of Renogy and its licensors. The User Manual may not be
modified, reproduced, or copied, in whole or in part, without the prior written
permissions of Renogy and its licensors.
The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA
Date and Revision
June 2023, Revision V1.0

CATALOG
1. Introduction.........................................................................................................................................4
2. Production description......................................................................................................................4
2.1 Bluetooth module....................................................................................................................4
2.2 RF antenna..............................................................................................................................5
2.3 Application note.......................................................................................................................6
3. Label and FCC ID & IC.....................................................................................................................7
5. Statements .........................................................................................................................................8
6. Manufacturer information ...............................................................................................................12

1. Introduction
The RNGBTCM001 contains a Bluetooth low energy single mode module and
an antenna. It could be used for wireless communication.
The RNGBTCM001 provides flexible interface that could be powered with 3.3V
power rail. It consumes only 0.15uA in lowest power shutdown and will wake
up in few microseconds.
The transmission distance is 100 meter.(at face to face, free space, 1.2 meter
high from ground for testing).
2. Production description
Part number
Material type
RNGBTCM001
Bluetooth module
RNGBTCM001
antenna
1.01.21.11.0028.00
The Bluetooth communication contains two parts, as below figure.
The RNGBTCM001 figure
The antenna should be assembly to the external of unit’s shell when
RNGBTCM001 is used to transmit data for a unit. The Bluetooth should be
welding to PCB of unit.
2.1 Bluetooth module
Part number
vender
description
HY-40R204IC
SHENGRUN
External antenna with IPEX
interface, with shielding case
The HY-40R204IC is fulfilled：Bluetooth V4.2 single mode compliant.
Transmit power :+5 dBm typical
Receiver sensitivity: -97dBm typical
Ultra low current consumption :Shutdown. No clocks running, no retention: 150
nA(Typical)
Programmable ARM Cortex-M3 processor for embedding full applications.
PCBA dimension size and figure

The detailed interface definition see HY-40R204IC specifications.
2.2 RF antenna
The antenna contains connection wire, antenna, protection case,nut. As
below.
The RF antenna figure
nut
Protection case
antenna

The antenna is assembly that should open hole on shell of unit, the hole size is
6.3mm as below.
Assembly hole size
2.3 Application note
The around antenna placement that is assembled on unit’s case should be
near metal and prevent material existence of electromagnetic radiation,
this will affect the transfer distance. Recommendation as below.
The fixed antenna nut should be fulfilled requirement of torque, the
excessive torque will lead to damage the teeth of antenna, the small torque
will cause that the antenna is loose. Recommendation torque is 0.3±
0.05N*m.
Attention to the electrostatic protection, prevent the soldering iron and the
equipment grounding bad; And the workbench, working environment,
packaging materials and from the human body Touch with static electricity,
etc., destroy IC ; Manual welding module solder iron temperature, should
pay attention to avoid the PCB copper stripping off; Soldering iron strictly
Grounding requirements, eliminating solder iron leak voltage and avoid
supply power Vcc switch instant turn on/ turn off state ,generate high
voltage, May be let the module to damaged; Recommended operating
voltage 2.4V~3.3V, operation temperature range -40℃~85℃. ESD ratings
as below table.

Attention to avoid the overall motherboard power supply circuit of bad
welding connected to short circuit or open circuit, causing the Bluetooth
chip, abnormal voltage, The software will fly and problems of IC was
damaged.
Use the module in the production and the transport process, please insure
module’s component protection, prevent the precision parts on the module
damaged.
The module is humidity sensitive components ( MSD level 3), if used in
SMT reflow soldering operations, please strictly follow the
IPC/JEDECJ-STD-020 regulation, completes the drying dehumidifying,
and for this module has second processing work after placed in the
functional test environment, the humidity of the chip is no guarantee that in
a certain ratio, The attention note show in below figure.
3. Label and FCC ID & IC
Label should contain model number and FCC ID and IC number.
The model number of Bluetooth communication module is RNGBTCM001.
FCC ID is 2ANPB-RIV1230RCH.
IC is 23590-RIV1230RCH.
MIC is TBD until MIC report finished.
The label size is 12mm*9.5mm, it should be pasted to shield case.
4. Antenna size, gain and test data information
For antenna size as section 2.2 antenna figure.
Individually tested antenna, tested data:
return loss is -10.2dB at 2.4GHz
VSWR is 1.65
Gain is 3.56dBi
Tested wave as below figures, measuring frequency 2.4GHz~2.5GHz.

Return loss VSWR
2.4GHz measured data
2.5GHz measured data
5. Statements
FCC/Industry Canada Statement (to be placed on End Products)Federal
Communications Commission (FCC) Statement
FCC Statements:
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
---- Reorient or relocate the receiving antenna.
---- Increase the separation between the equipment and receiver.
---- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
---- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Integration instructions for host product manufacturers according to KDB 996369
D03 OEM Manual v01
2.2 LIST OF APPLICABLE FCC RULES:
Compliance with §15.247 regulation
2.3 SPECIFIC OPERATIONAL USE CONDITIONS:
The module is typically use in industrial, household and general office / ITE
and audio & video, EV charging system end-products. The product must not
be co-located or operating in conjunction with any other antenna or
transmitters.
2.4 LIMIT MODULE PROCEDURES:
Not applicable as this radio module meets the Single-Modular transmitter
requirements.
2.5 TRACE ANTENNA DESIGNS:
The module was designed with the fixed PCB print antenna and the maximum
gain is about 3.56dBi between 2400-2500MHz, any changes or modifications

by the OEM integrator will require additional testing and evaluation.
2.6 RF EXPOSURE CONSIDERATIONS:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This product must be installed and operated with a
minimum distance of 20 cm between the radiator and user body.OEM
integrator shall equipped the antenna to compliance with antenna requirement
part 15.203& 15.204 and must not be co-located or operating in conjunction
with any other antenna or transmitters,otherwise, a Class II Permissive
Change (C2PC) must be filed with the FCC and/or a new FCC authorization
must be applied.
2.7 ANTENNAS:
The antenna of the module was deisgned as PCB printed on the PCBA board
and the best gain is about 3.56dBi between 2400-2500MHz. Modification the
antenna design may need additional testing and evaluation.
2.8 LABEL AND COMPLIANCE INFORMATION:
The final end product into which this RF Module is integrated has to be labeled
with an visible area and stating the FCC ID of the RF Module, such as
"Contains FCC ID: 2ANPB-RIV1230RCH". If the size of the end product is
smaller than 8x10cm, then additional FCC part 15.19 statement is required to
be available in the users’ manual: This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
The User's Manual for The finished product should include the following
statements:
Integrator is reminded to assure that these installation instructions will not be
made available to the end-user of the final host device.