Renu Electronics FP4043T User manual

Power (Base) 24VDC(±15%), 140mA, 3.36W (T-E module)
24VDC(±15%), 160mA, 3.84W (TN-E module)
Power
(With 1 Expansion)
24VDC(±15%)
,
190mA, 4.56W
(T
-
E module)
24VDC(±15%), 210mA, 5.04W (TN-E module)
Display 4.3” WQVGA color TFT with 4-wire analog resistive
touch screen
LEDs
1
RAM Memory 512MB
User Application
Up to 1GB that incl
udes user application,
alarms,
retentive memory and logic memory
Internal Datalog
50 MB
eMMC
4GB
RTC Built-in, date and time function
Expansion
It support 1 expansion slot
Weight Approx. 400gm
Panel Cutout 111.00mm(W) x 80.00mm(H)
Product
Dimensions 120.00mm(W) x 89.0mm(H) x 31.5mm(D)
Communication
Serial Port 1 x RS232, RS485#
USB Ports
1 USB Device and 1 USB Host
Ethernet 1 Ethernet Port
SD Card
Micro SD [High Capacity (4GB to 32GB)]
Speed Class:
[While inserting and removing SD card, please make
sure to TURN OFF the power to the unit.]
Environment & Approvals
Operating
Temperature -10° to 60°C*
Storage
Temperature -20° to 85°C
Humidity
10 to 90% (Non-Condensing)
Shock
IEC 60068
-
2
-
27
25g, 11ms, 6 shocks per axis, total 18 shocks (X, Y,
Z)
Vibration
IEC 60068
-
2
-
6
5 to 150Hz, 3g peak (X, Y, Z)
EMC
EN 55011 : 2009/A1 : 2010
EN 61131-2 : 2007
EN 61000-6-2 : 2005/AC : 2005
EN 61000-6-4 : 2007/A1 : 2011
Protection IP66 for front panel mounting
APPROVALS CE, UL (Class1 Div2) & RoHS
[# Note: FP4043Tx-E support one DB9 port that supports RS232 & RS485
levels on different pins. “Y” type cable can be used for separate RS232 and
RS485 levels simultaneously.]
(Part No.: REPL Part# EC-Y-FP)
[
*
Note:
For UL, operating temperature range is 0
°
to 50
°
C
.
]
SPECIFICATIONS
PRODUCT DIMENSIONS
Panel Cutout Dimensions: 111.00 x 80.00mm,
Panel Thickness: Maximum 6mm
Mounting Clamps: 4
QUICK START GUIDE
FP4043 Series
Product Code:
FP4043T: 4.3”, 480 x 272 pixels, WQVGA color TFT with 4-wire
analog resistive touch screen with 2 serial ports#, one USB Device
port & 1 USB Host port
FP4043TN: 4.3”, 480 x 272 pixels, WQVGA color TFT with 4-wire
analog resistive touch screen with 2 serial ports#, one USB Device
port, one USB Host port, 1 Ethernet port & SD card slot
FP4043T-E: 4.3”, 480 x 272 pixels, WQVGA color TFT with 4-wire
analog resistive touch screen with 2 serial ports#, one USB Device
port & 1 USB Host port. It supports 1 expansion module.
FP4043TN-E: 4.3”, 480 x 272 pixels, WQVGA color TFT with 4-wire
analog resistive touch screen with 2 serial ports#, one USB Device
port, one USB Host port, 1 Ethernet port & SD card slot. It supports
1 expansion module
[# Note: For more information about #, please refer specifications
section.]
User should follow the given sequence to configure and
use any Flexipanels series unit:
1.
Install FlexiSoft Software.
2.
Create a PZM application using FlexiSoft software.
3.
Connect programming cable.
4.
Download firmware i.e. driver for the HMI.
5.
Download application.
6.
Now FP unit is ready to use in the system.
GETTING STARTED

This section provides information regarding communication interfaces
supported by this product.
Serial Port
1 Physical Port : Com1-RS232, Com2-RS485
DB9 Female
Pin number
Signal
1 TX+
2 TXD
3 RXD
4 RX+
5 SG
6 NC
7 NC
8 TX-
9 RX-
Y Type Cable
Special “Y” cable for FP unit (two communication levels on one
port).
Cable Diagrams:
PC to unit programming cable: RS232 Pinout
WARNING:
-> This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D
or non- hazardous locations only.
-> WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless
power has been removed or the area is known to be non-hazardous.
-> WARNING – EXPLOSION HAZARD - Substitution of components may impair
suitability for Class I, Division 2.
-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not Recharge,
Disassemble or Dispose of in Fire.
-> The list of materials used in the construction of these devices with name of
sealed device - generic name of the material and the supplier's name and type
designation.
-> It is recommended that the user periodically inspect the sealed devices
used, for any degradation of properties and Replace the device if any
degradation is found.
Rev.
Description
Date
1.0
First Draft
24/03/2020
1.1
Combined FP4043Tx
-
E
information
01/09
/2020
1.2
FP4043 models combined
1
0
/02/2022
Note: Details shown here are subject to change. For latest version of
the product datasheet please scan the QR code.
REVISION HISTORY
2 Wire RS485
connections:
4 Wire RS485 connections:
USB Slave Port
1. USB Type C, compliant with USB 2.0 specification, self-
powered device.
2. Connector used: USB Type C Female connector.
USB Host Port
1. USB Host, compliant with USB 2.0 specification.
2. USB Host can handle only USB memory stick devices and
can source current up to 150mA only.
3. Connector used: Standard USB Type A Female connector.
Ethernet Port
1. Fully compliant with IEEE 802.3 / 802.3u standards.
2. 10/100Mbps support.
3. Connector used: Standard shielded RJ-45 female jack with
in-built speed and link activity indication LEDs.
Pin number
Signal
1 TX+
2 TX-
3 RX+
4 NC
5 NC
6 RX-
7 NC
8 NC
Earthing
The optimum method for Earthing electronic equipment is to earth
it separately from other high-power systems, to earth more than one
unit of electronic equipment with a single-point earth. The Earthing
marked terminal (see below) is provided on the unit.
[Note: Do not use an earth that has an unstable impedance, such as
painted screws or earth subject to vibration.]