Renu Electronics WP6101TN Plus User manual

Panel Cutout Dimensions: 256.00 (W) x 178.00(H)mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 6
Tighten the mounting screws evenly to a torque between
0.4N/m to maintain water and dust resistance.
Product Code: WP6 101 TN Plus
The WP6 Plus is a ThinClient with an inbuilt browser,
which connects to a remote Web server on its
network.
All WP6 devices are compliant with EMC directive
2014/30/EU and LVD directive 2014/35/EU and
certified for UL Class I Div. 2.
For More Information, Visit
https://www.renuelectronics.com
Power
24VDC (+20%, - 15%), 350mA ,
8.5W
Display
1024 x 600pixels , 10.1" Color TFT,
WQVGA Web Panel Analog
Resistive Touch Screen
Memory
eMMC: 4GB
RAM: 1GB
USB Ports
1 USB Slave and USB Host
Ethernet
1 Ethernet Port
Panel Cutout
256.00(W) x 178.00(H)mm
Dimensions
268.00(W) x 190.00(H) x 33.00(D)mm
Weight
Approx. 900gm
LED
1
Environment & Approvals
Operating Temperature
0 to 50°C
Storage Temperature
-20 to 85°C
Humidity
10 to 90% (Noncondensing)
Shock
IEC 60068-2-27
25g, 11ms, 6 shocks per axis, total
18 shocks (X, Y, Z)
Vibration
IEC 60068-2-6
5 to 150Hz, 3g peak (X, Y, Z)
EMC
EN 55011 : 2009/A1 :2010
EN 61131-2 : 2007
EN 61000-6-2 : 2005/AC : 2005
EN 61000-6-4: 2007/A1: 2011
Protection
IP66 for front panel mounting
Approvals
CE, UL & RoHS compliant
Default Product Settings
Network Settings
DHCP
Brightness
Full Scale
Screen Touch Beeper
On
Default Language
English
SPECIFICATIONS
PRODUCT DIMENSIONS
QUICK START GUIDE
WP6101TN Plus
PANEL CUTOUT DIMENSIONS
INTRODUCTION
Series
Display Size
4.3”
RIGHT SIDE
VIEW
BOTTOM VIEW
TOP VIEW
LEFT SIDE
VIEW
FRONT
VIEW
Supports Ethernet

Rev.
Description
Date
1.0
First Draft
11/06/2021
1.1
Added password information
14/10/2021
1.2
Renu Logo updated
19/05/2023
Renu Electronics Pvt. Ltd® reserves the right to change or
discontinue specifications and features without prior notice.
To view the latest and updated datasheets/manuals please visit
www.renuelectronics.com.
REVISION HISTORY
UL APPROVAL
To use the WP6 Plus as a browser, follow these steps to
connect the device to a Webserver. The Password for
configuring the device is admin@123.
[Note: For configuring new Password it must be at least
7 or more charterers with 1 capital letter (0-9, a-z, A-Z)]
1. Connect an Ethernet cable to the device.
2. Power up the device using 24VDC power supply by
connecting it to the device’s pluggable terminal
block.
3. If the browser or the firmware needs to be updated,
connect a USB flash drive to the device.
Settings
Description
Device Settings button. Settings for
Network, Calibration, Password and
Brightness can be accessed using this
button.
URLs Settings button.
Device Information button.
Earthing
The optimum method for Earthing electronic equipment
is to earth it separately from other high-power systems
and to earth more than one unit of electronic equipment
with a single-point earth. The Earthing marked terminal
(see below) is provided on the unit.
[Note: Do not use an earth that has an unstable
impedance, such as painted screws or an earth subject
to vibration.]
This section provides information regarding
communication interfaces supported by this
product.
RJ45/Ethernet Port
The WP6 Plus series devices come with an in-built
RJ45/Ethernet port. The RJ45 port is a shielded
female jack with link and activity LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
USB Slave Port (2.0)
The WP6 Plus comes with a Type C USB device
port.
Pin number
Signal
1
GND
5
D-
6
D+
7
D-
8
D+
12
GND
USB Host Port
The WP6 Plus devices supports one USB Host
port that connects to a USB 2.0 compatible USB
Flash drive.
This port can be used to upgrade the firmware and
the browser.
Pin number
Signal
1
VCC
2
D-
3
D+
4
GND
WARNINGS
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C and D or non-hazardous locations only.
WARNING –EXPLOSION HAZARD –Do not disconnect
equipment unless power has been removed or the area
is known to be non- hazardous.
WARNING –EXPLOSION HAZARD - Substitution of
components may impair suitability for Class I, Division 2.
The list of materials used in the construction of these
devices with name of sealed device - generic name of
the material and the supplier's name and type
designation.
It is recommended that the user periodically inspect the
sealed devices used, for any degradation of properties
and replace the device ifany degradation is found.
GETTING STARTED
MAIN SETTINGS
COMMUNICATION
CONTROL DRAWING NO# CNTL/DWG/FP6101/0218 VER.N O.: 1.00