Repotec RP-G1416D User manual

1
FCC Certifications
This Equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to the
EMC Directive 2004/108/EC, the Low Voltage Directive
2006/95/EC, and the RoHS Directive 2011/65/EU.
Company has an on-going policy of upgrading its products
and it may be possible that information in this document is not
up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright © 2013, All Rights Reserved.

2
Introduction
General Description
Easily boost your networking throughput, the rack-mountable
switch provides you 16/24* 10/100/1000Mbps Gigabit ports
that lead you to a real Gigabit connection. Users are now able
to transfer large and high bandwidth-needed files faster and
hence get a real efficiency improvement.
The switch offers users with fast and reliable network. The
store-and-forward architecture filters errors and forwards
packets in a non-blocking environment. Flow control ensures
the correctness of data transmitting. The 802.3x and
backpressure flow control mechanisms work respectively for
full and half duplex modes.
The switch features with easy installation and maintenance. It
supports N-Way auto-negotiation protocol, which detects the
networking speed (either 10/100/1000 Mbps) and the duplex
modes (Full or Half duplex mode) automatically and do an
immediately adjustment to advance the capability and
performance. Auto-MDI/MDI-X function alleviates the effort to
use crossover cables. Users need not to prepare crossover
cables for equipment connectivity. Also, rich diagnostic LEDs
are provided for users to get real-time information of the
connection status that helps to do quick response and
correction.
Unpacking Information
Thank you for purchasing this product. Before installation,
please verify that your package contains the following items.
1. One 16/ 24–Port Gigabit Ethernet Switch
2. One AC power cord
3. Wall mount kit
4. Rubber feet
5. User’s Manual

3
Key Feature
Complies with 10BASE-T specifications of the IEEE802.3
standard
Complies with 100BASE-TX specifications of the
IEEE802.3u standard
Complies with 1000BASE-T specifications of the
IEEE802.3ab standard
16/24 * 10/100/1000Mbps RJ-45 N-Way ports
Supports N-Way protocol for speed (10/100/1000Mbps)
and duplex mode (Half/Full) auto-detection
Supports MDI/MDI-X auto crossover
Supports full and half duplex operation on all ports
Supports back-pressure (half duplex) and flow control
(IEEE 802.3x)
Store-and-forward architecture filters fragment & CRC
error packets
Supports 8K bytes MAC address entries in whole system
256K (16-Ports model) / 512K(24-Ports Model) bytes
buffer memory
Support up to 9K (16-Ports model) / 10K (24-Ports Model)
jumbo frames
Supports extensive LED indicators for network
diagnostics
Rack mountable
Support EEE(802.3az) feature on/off push button for
power saving or performance mode.
Support power switch (On / Off)
Internal power supply
100~240VAC/50~60Hz universal input
FCC, CE Class B, LVD EN60950-1
RoHS compliant

4
Front Panel
The front panel consists of LED indicators and the ports. For
detailed LED definition, please refer to the next paragraph.
The front panel of the switch is shown as below:
16 port Model
24 port Model
LEDs Definition
Both the 16/24 port switches contain one power LED for the
device, Link/Act LEDs for each port that shows the activities
and information of the ports.
LED for the device
Power LED -
The switch provides a power LED for the device.
LED
Status
Operation
Power
Steady Green
Switch is ready to work
Blinking Green
Switch is under booting
Off
Switch is powered off
Port LEDs -
The switch provides one “Link/ACT” LED for each port.
LED
Status
Operation
Link/
ACT
Steady Green
Valid port connection
Blinking Green
Valid port connection and
there is data transmitting/
receiving
Off
Port disconnected

5
Rear Panel
The power receptacle and power on/off switch is located on
the rear panel of the switch:
16 port Model
24 port Model
Power Receptacle
To be compatible with the electric service standards around
the world, the switch is designed to afford the power supply in
the range from 100 to 240VAC, 50/60Hz. Please make sure
that your outlet standard to be within this range.
To power on the switch, plug the female end of the power
cord firmly into the receptacle of the switch and the other end
into an electric service outlet. After the power cord installation,
please turn on the back panel power switch to check if the
power LED is illuminated for a normal power status.

6
Installation
This switch can be placed on your desktop directly, or
mounted on the wall. The installation is a snap. Users can use
all the features of the switch with simply attaching the cables
and turning the power on.
Before installing the switch, we strongly recommend:
1. The switch is placed with appropriate ventilation
environment. A minimum 25mm space around the unit is
recommended.
2. The switch and the relevant components are away from
sources of electrical noise such as radios, transmitters
and broadband amplifiers.
3. The switch is away from environments beyond
recommend moisture.
Desktop Installation
You need to attach the provided rubber feet to the bottom of
the switch before installing for keeping the switch from
slipping. The recommend position has been square-marked.
1. Install the switch on a level surface that can support the
weight of the unit and the relevant components.
2. Plug the switch with the female end of the provided
power cord and plug the male end to the power outlet.
Wall mount Installation
1. Screw the two provided screws into the wall 150 mm
apart horizontally. Leave a small gap between the head of
the screw and the wall. The gap should be big enough for
the screw heads to slide into the screw slots and the
connection cables to run down the back of the switch.
2. Align the holes on the back of the switch with the screws
on the wall. Hang the switch on the screws.
Note: Do not mount the product vertically or it will be
dangerous. Please attach the product on the wall horizontally!
See the image below for reference:

7
Station Connection
Connect each station to the switch by twisted-pair cable. Plug
one RJ-45 connector into a RJ-45 port of the switch, and plug
the other RJ-45 connector into the station’s network adapter.
Power on the switch and then system is ready.
Switches Connection
Network Cables Installation
1. Crossover or straight-through cable: All the ports on
the switch support Auto-MDI/MDI-X functionality. Both
straight-through or crossover cables can be used to
connect the switch with PCs as well as other devices like
switches, hubs or router.
2. Category 3, 4, 5, 5e or 6 UTP/STP cable: To make a
valid connection and obtain the optimal performance.
Appropriate cables corresponding to different
transmitting/receiving speed is required. To choose a
suitable cable, please refer to the following table.
Media
Speed
Wiring
10/100/1000Mbps
10Mbps
Category 3, 4, 5
UTP/STP
100Mbps
Category
5 UTP/STP
1000Mbps
Category 5e, 6
UTP/STP

8
Product Specifications
Standard
802.3 Ethernet,
802.3u Fast Ethernet,
802.3ab Gigabit Ethernet ,
802.3x flow control for full duplex,
802.3az Energy Efficient Ethernet
support ,
802.1p CoS
Interface
16/24 * 10/100/1000Mbps auto
MDI/MDI-X RJ-45 switching ports
Cable
Connections
RJ-45 (10BASE-T): Category 3,4,5
UTP/STP
RJ-45 (100BASE-TX): Category 5
UTP/STP
RJ-45 (1000BASE-T): Category 5e, 6
or enhanced UTP/STP
Network Data
Rate
10/100/1000Mbps Auto-negotiation
Transmission
Mode
10/100Mbps: Full-duplex, Half-duplex
1000Mbps: Full-duplex
LED
Indications
Per Unit: Power and System status
Per Port: Activity/Link
Memory
8K MAC entries ;
256K (16-Ports model) / 512K
(24-Ports model) buffer Memory
Jumbo Frame
9K (16-Ports model) /
10K (24-Ports model) bytes
Emission
FCC, CE Class B
Operating
Temperature
0℃~ 50℃(32℉~ 122℉)
Operating
Humidity
10% - 90%(non-condensing)
Power Supply
Internal power supply 12V 1A
(16-Ports model) / 12V 1.67A
(24-Ports model)
100-240V/50-60 Hz universal input