Repotec RP-G108Q User manual

RP-G108Q
8-Port Gigabit Switch
Quick Installation Guide
V1.0

1
1.
Before You Start
Package Contents
1. RP-G108Q
2. Quick Installation Guide
3. AC Power Adapter (5 VDC, 1 A)
Installation Requirements
n A computer with a network adapter installed
n Cat-5e or Cat-6 Network Cable
n The surface must support at least 1,5 Kg for the Switch.
n The power outlet should be within 1.82 meters (6 feet) of the Switch.
n Make sure that it is securely connected to the power adapter.
n Make sure that there is proper heat dissipation from and adequate ventilation around the
Switch.
n Do not place heavy objects on the Switch
2.
Application

2
3.
Hardware Installation
Notice
The cable distance between 16/24 port Switch and other IEEE802.3 compatible network device should
not exceed 100 meter. Make sure the wiring is correct. It can be used Category 3/4/5 cable in 10 Mbps
operation. To reliably operate your network at 100Mbps, you must use an Unshielded/Shielded
Twisted-Pair (UTP/STP) Category 5 cable, or better Data Grade cabling. While a Category 3 or 4 cable
may initially seem to work, it will soon cause data loss. All kinds of IEEE802.3 compatible network device
(Hub, Switch, PC) can connect to Switch by using straight-through wires or crossover wires because of
Switch's auto MDIX function.
4.
LEDs
3. Connect the AC Power Adapter to
the RP-G108Q and then to a
power outlet.
4. Connect a CAT-5e or CAT-6
RJ-45 network cable from the
computer to RP-G108Q.
Power
Green: Power is on.
Not Illuminated: Power is off.
Loop
Red (Blinking): Loop detected
Not Illuminated: Nothing is detected on the port.
Link/ACT
Green(Solid): Link to another device.
Green(Blinking): Activity is occurring from the link
Not Illuminated: Nothing is detected on the port.

3
5.
Technical Specifications
Standards
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x Flow Control
Cables
Ethernet: Cat. 3,4,5, up to 100m
Fast Ethernet: Cat. 5, up to 100m
Gigabit Ethernet: Cat. 5, 5e,6, up to 100m
Data Transfer Rate
Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex)
Gigabit Ethernet: 2000Mbps (full-duplex)
Protocol / Topology
CSMA/CD / Estrela
Interface
8* 10/100/1000 Mbps RJ-45 ports
Data RAM Buffer
256K bytes
Jumbo Frame Support
9K bytes
Switch Fabric
16Gbps Forwarding Capacity
MAC Address Learning
Automatic Update
Filtering Table
8K entries per device
Temperature
Operating: 0° ~ 40° C (32° ~ 104° F)
Storage: -10° ~ 70° C (14° ~ 158° F)
Humidity
Operating: 10% ~ 90%
Storage: 5% ~ 90%
Diagnostic LEDs
Power, Link/ACT, Loop detection
Power Adapter
5V DC, 1A External Power Adapter
Dimensions
150 x 80 x 29.8 mm
Certification
FCC, CE Class B, LVD

RP-G108Q
8-Port Gigabit Switch
Guia de Instalação Rápida
V1.0
P/N:41AR-G108Q000-A00

1
1.
Antes de Iniciar
Conteúdo da Embalagem
4. RP-G108Q
5. Guia de Instalação Rápida
6. Adaptador Externo de Tensão (5 VDC, 1 A)
Requisitos Mínimos
n Computador com adaptador de rede instalado
n Cabo de rede Cat-5e ou Cat-6
n Superfície deve suportar no mínimo 1,5 Kg
n A tomada elétrica deve estar a no máximo 1,82 metros (6 feet) do Switch.
n Assegure-se de que o cabo de alimentação está adequadamente conectado.
n Assegure-se de que há ventilação adequada e dissipação de calor aproriada no entorno do
Switch
n Não coloque objetos pesados sobre o Switch
2.
Aplicação

2
3.
Instalação do Hardware
Aviso
The cable distance between the Switch and other IEEE802.3 compatible network device should not
exceed 100 meter. Make sure the wiring is correct. It can be used Category 3/4/5 cable in 10 Mbps
operation. To reliably operate your network at 100Mbps, you must use an Unshielded/Shielded
Twisted-Pair (UTP/STP) Category 5 cable, or better Data Grade cabling. While a Category 3 or 4 cable
may initially seem to work, it will soon cause data loss. All kinds of IEEE802.3 compatible network device
(Hub, Switch, PC) can connect to Switch by using straight-through wires or crossover wires because of
Switch's auto MDIX function.
4.
LEDs
1. Conecte o Cabo de
Alimentação ao RP-G108Q e
então a uma tomada elétrica.
2. Conecte o Cabo de Alimentação ao RP-G108Q e
então a uma tomada elétrica.
Power
Verde: Ligado.
Não Iluminado: Desligado.
Loop
Vermelho (Piscando): Loop é detectado
Não Iluminado: Nada é detectado na porta.
Link/ACT
Verde (Estático): Conectado a outro dispositivo.
Verde (Piscando): Link em atividade.
Não Iluminado: Nada é detectado na porta.

3
5.
Especificações Técnicas
Standards
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x Flow Control
Cabos
Ethernet: Cat. 3,4,5, up to 100m
Fast Ethernet: Cat. 5, up to 100m
Gigabit Ethernet: Cat. 5, 5e,6, up to 100m
Taxa de Transferência de
Dados
Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex)
Gigabit Ethernet: 2000Mbps (full-duplex)
Protocolo/Topologia
CSMA/CD / Estrela
Interface
8* 10/100/1000 Mbps RJ-45 ports
Data RAM Buffer
256K bytes
Suporte a Jumbo Frame
9K bytes
Switch Fabric
16Gbps Capacidade de Encaminhamento
Aprendizado de
Endereço MAC
Atualização automática
Tabela de Filtragem
8K entradas por dispositivo
Temperatura
Funcionamento: 0° ~ 40° C (32° ~ 104° F)
Armazenamento: -10° ~ 70° C (14° ~ 158° F)
Umidade
Funcionamento: 10% ~ 90%
Armazenamento: 5% ~ 90%
LEDs de Diagnóstico
Power, Link/ACT, Loop detection
Adaptador Externo de
Tensão
Adaptador Externo de Tensão 5V DC, 1A
Dimensões
150 x 80 x 29.8 mm
Certificação
FCC, CE Class B, LVD