Repotec RP-PE801 User manual

1
Quick Installation Guide
8Port PoE+1Uplink/IEEE802.3at/100Mbps
Introduction
The PoE switch supports IEEE 802.3at standard for Power over Ethernet (PoE) with the
maximum power delivery up to 150 Watts. That makes it suitable to various applications that
demand for remote power feeding and meet high level requirement for power. The PoE
switch is totally equipped with 30 Watts per PoE port, which effectively helps allocate power
for connected
Key Features
•Compliant with IEEE 802.3at standard
•Supports Power over Ethernet on 8 ports of 10/100M
•Provides 135Watts (max) Power
•Supports Auto-MDI/MDI-X
•Support Non-Blocking Data Forward
•Supports Auto-Negotiation and feature of store-and-forward
•LED indicators for PoE activity
Package Contents
Before you start installing package contents:
•PoE Switch x 1
•Quick Installation Guide x1
•Power Cord x1
•Mounting Kits & Screw
•Rubber feet x4

2
Front Panel
LED indicators
For definitions of LED indicators, please refer to the following table:
LED
Status
Indication
PWR
On/Green
Power is On
Off
Power is off
UpLink
On/Green
Uplink port is in connection
Blink/Green
Receiving or transmitting data
Off
No device attached
ACT
Port1~8
On/Green
The Ethernet port is connecting with the device
Blink/Green
Receiving or transmitting data
Off
No device attached
PoE
Port1~8
On/Orange
PoE port is active
Off
PoE port is not active
Back Panel
Power Switch and Power Cord Connector
Hardware Installation
The setup of the switch can be performed using the following steps:
Step 1: Connect the Power Cord to the POE switch and then to a power outlet
Step 2: Connect a RJ-45 Ethernet cable from IEEE802.3af/at compliant devices (PD) to an
available PoE port
Note : Port 1 to Port 8 are used for connecting to PD or PoE splitter for end devices.

3
For cable selection, refer to the following table:
Network Speed
Cable Type
Max. Length
10M
Cat.3,4,5,5eUTP/STP
100 meters
100M
Cat. 5,5e UTP/STP
100 meters
Note :To prevent costly equipment damage and downtime, please consider installing a surge
uppression device or a UPS (Un-interrupted Power Supply).
Specifications
Standards
IEEE 802.3at
IEEE 802.3 10 BaseT
IEEE 802.3u 100 BaseTX
IEEE 802.3x Flow Control
Features
Number of Ports: 8 PoE/PSE ports+1 Up link port
MAC Address: 1k
Buffer Memory: 512 bits
Transmission Method: Store and Forward
Transmission Media
10 BaseT Cat 3,4,5 UTP/STP
100M BaseTx CAT 5 UTP/STP
LED Indicators
Per Port: Link/Act, PoE Act/Status
Per Unit: Power
Power Input/Output
Input: 100~240V/AC, 50~60 Hz
Output: 44-57V/DC Per Port Output- 30W
Max Per Port, 8 Ports at Full 15.4 W Output Supported
Power Consumption
135Watts(Max)
Dimensions: (L x W x H) /
Weight
282.2 x 178 x 44 mm / 1500g
Temperature
Operating: 0 ~ 40°C
Storage: -20~70°C
Humidity: 10~90%, Non-condensing
Safety Approvals
CE, FCC, EN 60950:2006
Regulatory
RoHS Compliant, CE/FCC

4
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022
class A for ITE, the essential protection requirement of Council Directive 2004/108/EC on the
approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information
in this document is not up-to-date. Please check with your local distributors for the latest
information. No part of this document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2013, All Rights Reserved.
(P/N: 41NE-PE801000-A00)