Resolution Products RE311 Mighty Mouse User manual

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 1 of 4
13-Ma -12
www.ResolutionProducts.com
RE311 Mighty Mouse™ DSC-Compatible Micro Door Sensor
Features
•Smallest Door/Window Sensor & Magnet in the Industr .
•Full-sized transmit range, AND…
•4-6 ear batter life on CR1632 batter .
•Invisible external antenna – gives great range and long life
•Low Batter indication.
Mounting
Antenna Routing Options
ireless
Security
Solutions
Run
a light coat of
permanent paste
glue on the
underside of the
antenna
wipe it down
with finger
Remove
High Bond
tape liners
Align
centering marks
Position
Antenna free and clear of sensor;
not inside cover or under sensor.
DON’T MOUNT
ON METAL,
It will severel
reduce transmit
range and
magnetic gap
A.
Fasten with paste glue, as above.
B. Or let it la on surface, nearl invisibl .
D.
Drill hole and
thread antenna down
C.
Route into trim gaps or
along side of trim
1.
2
.
½ inch or less
magnet gap
3.
4.
RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 2 of 4
13-Ma -12
www.ResolutionProducts.com
Enrolling in Panel
.
1. Pull out the red tab to power the sensor.
2. Put DSC panel in Wireless Enrollment Mode.
3. Open (alarm) the DWS that ou want to enroll.
4. Confirm ESN, Enter Zone # and Zone T pe on DSC Panel.
5. Ma also be enrolled via entering ESN.
Internal Picture
O
pen
(Alarm) the
Sensor
Sensor sends
enrollment
signal
Batter
Minus side up
Reed Switch
Antenna
Batter
contacts

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 3 of 4
13-Ma -12
www.ResolutionProducts.com
Opening Cover
Replacing Battery
TO CLOSE
slide cover jaw into hinge.
Tilt closed.
Insert
Screwdriver
in slot
Tilt cover open.
Hinge is in back awa
from antenna
Insert Screwdriver
in slot.
Twist.
Note small
retention post
RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 4 of 4
13-Ma -12
www.ResolutionProducts.com
Specifications
Magnet trip distance: 1 inch nominal
Supervisories: Hourl
Batter Life: 4+ ears
Mounting fastener: 3M VHB (Ver High Bond) Tape
Replacement Batter : CR1632
Temperature Range: 0F to 120F
Housing dimensions: 1.75 x 0.75 x 0.2 inches
Antenna dimension: 2 inches
Specifications subject to change without notice.
Notices
“GE”, “Hone well”, “DSC” and “Napco” are trademarks owned b General Electric Compan ,
Hone well International Inc., T co Safet Products Canada LTD, and NAPCO Securit S stems,
Inc., respectivel .
Resolution Products, Inc. products will function with one of either GE, Hone well, DSC or Napco
s stems. However, no Resolution product is produced b , endorsed b , nor is officiall associated
with GE, Hone well, DSC or Napco. Resolution recommends verif ing proper enrollment and
operation, per control panel installation instructions, at installation.
Warrant
Resolution Products, Inc. will replace products that are defective in their first ear.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
This device ma not cause harmful interference.
This device must accept an interference that ma be received, including
interference that ma cause undesired operation.
Changes or modifications not expressl approved b the Resolution Products, Inc. could
void the user's authorit to operate this equipment.
FCC ID: U5X-RE311
IC Notice
This device complies with Industr Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device ma not cause interference, and
2. This device must accept an interference, including interference that ma
cause undesired operation of the device.
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE311