Resolution CryptiX PINPad RE652 Series User manual
RE652 Series CryptiX™ PINPad™
Mounting Screw Holes
VHB Tape
VHB Tape
PINPad is a simple arming station that allows local
control of the Helix panel. It is battery powered and
requires no installation tools. Many can be installed
throughout the home to provide convenient system
control.
Features
• Secure 4 to 10 digit disarming
• Supports 1-button arming
• Small yet comfortable
• 5 year warranty
Enroll by placing the panel into wireless enrollment
mode and then sending an enrollment signal from the
PINPad. Alternatively, the PINPad can be enrolled
by scanning its bar code using the HeliLink app or
by entering its 8-character serial number on the
interactive service provider’s web portal.
Option for sending an Enrollment Signal
• Press 1and 3buttons simultaneously
Install using the 3M VHB® tape on the back of the
PINPad to adhere it to a wall.
• See Pro Tips for recommendations about using
3M VHB tape.
• Two #4 or #6 screws may be used instead of,
or in addition to, the 3M VHB tape.
Operate using the PINPad buttons. The PINPad LED
will blink when a button is activated.
Disarm by entering a valid 4-10 digit user code on
the number pad.
Arm Away by pressing the AWAY button until the
PINPad LED ashes red.
Arm Stay by pressing the STAY button until the
PINPad LED ashes red.
Trigger a panic alarm by pressing the STAY &
AWAY buttons together until the PINPad LED
ashes red.
Enrollment Buttons
Arm Stay Arm Away
PINPad LED
Use the Helix installation guide to verify proper system setup.
I
N
S
T
A
L
L
G
U
I
D
E
I
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
2.28 x 1.97 x 0.40 inches (5.8 x 5.0 x 1.0 cm)
0.70 ounces (20 grams)
3M VHB™ Tape or #4/#6 screws (Mounting screws not provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% relative humidity non-condensing
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic CR2032
4 to 6 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 1 uA (Quiescent)
Low Battery, Supervision
Certication
RE652
RE652-CE
UL634, ULC634, FCC, IC
EN50131-1, EN 60950-1, EN300 220, EN301 489, CE, RCM
Specications subject to change without notice.
47-0007-08 • RevB • 2016-09-21
Tech Support (877) 260-5578
www.ResolutionProducts.com
WARRANTY
Resolution Products, Inc. will replace products that are defective in
their rst ve (5) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE652
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the Resolution
Products, Inc. could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE652
CE DECLARATION OF CONFORMITY
Hereby, Resolution Products, Inc. declares that this RE652-CE is
in compliance with the essential requirements and other relevant
provisions of directive 1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
Pro Tips
3M VHB Tape works great if the surface is properly prepared and rm pressure is applied
for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
To replace the battery insert a screwdriver into the latch slot
on the bottom of PINPad and pop the cover off the wall plate.
Replace the battery and reinstall the cover on to the wall
plate.
Latch Slot
Table of contents
Other Resolution Keypad manuals
