APO DK-9827 MK-II User manual
MULTI-PURPOSE
DIGITAL ACCESS CONTROL KEYPAD
DK-9827 MK-II
Programming & Installation Manual
FOR ELECTRIC LOCK, INTER-LOCK
AND SECURITY SYSTEM INSTALLATIONS
By AEI P RO TE CT - O N SY ST EMS
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
APPLICATION HINTS FOR THE AUXILIARY FACILITIES
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4-6
························································································································· 6
··········································································· 6
·········································································· 7-9
······································································································ 10-26
············································································································· 10
····························································································· 10
············· 10
······························································································ 11
··················································································· 11
······································································································· 12
························································································ 13-14
·································································································· 15
··································································································· 16
·············································································· 17
····························································· 18-19
·················································································· 20
················································································ 21
··························································································· 22
······································································································ 22
··················································································· 23
·················································································································· 23
································································································ 23
·········································································································· 24-25
·········································································· 25
············································· 26-27
································································ 26
·········································································· 27
······························································································································ 28
············································································································ 29-31
······························································ 32-34
············································································································· 35
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
Output 1 Output 2 Output 3 Door Bell
3 Amp Solid State 1 Amp Relay NPN Open Collector 1 Amp Relay
KEY AL
K OR A
ON OFF
DAP
INTRODUCTION
DK-9827 is an universal, self-contained, weatherproof digital access control keypad oers eld proven reliability and
cost eective solutions for residential and commercial installations. It is designed for stand alone electric lock and
inter-lock systems and operates froma12 to 24V AC/DC power supply. It is virtually compatible with any electric
locking device. Apart from that it is also the perfect choice for controlling security systems, automatic operators and
machinery.
DK-9827 consists two application softwares of Single User Mode for the general Users, and Multi-User Mode for the
advanced Users. The system oersa4digit length user code with 10,000 combinations for each output in single user
mode; and 100 user codes for output 1 and 10 user codes each for output2and output3in length of 4-8 digits with
combinations of more than 100 million in multi-user mode. Operation options of Auto Code entry and Manual Code entry
are available in both two user modes. Programmed information that stored in the system are non-volatile in power failure.
The DK-9827 oers the following output facilities:
Normally Closed contact while the keypad is secured on the box. It is open while keypad is separated from the
box. Connect this N.C. terminal toa24 hour zone of an alarm system if necessary.
A Normally Open relay output dry contact with maximum rating of 30VDC/1A prepared as the triggering point of
a door chime.
TAMPER N.C.
DOOR BELL
CONNECTION FACILITIES
2
OUTPUT 1
5 Amp relay
OUTPUT 3
NPN Open Collector
DOOR BELL
1 Amp relay
OUTPUT 2
1 Amp relay
TAMPER
RELAY 1
RELAY 2
RELAY 3
( ) ( )
12 24V
AC/DC
EG
IN
TAMPER
N.C.
DOORBELL
N.O.
OUTPUT 1
N.C. COM N.O.
INT.
LOCK
O/P 1.
INHIB.
DU
OUT
( )
GND
DOOR
SENS
KEY
ACT
O/P
3
OUTPUT 2
N.C. COM N.O.
ON OFF
DAP
KEY AL
K OR A
DK-9827
5
( ) ( )
12 24V
AC/DC
EG
IN
TAMPER
N.C.
DOORBELL
N.O.
OUTPUT 1
N.C. COM N.O.
INT.
LOCK
O/P 1.
INHIB.
DU
OUT
( )
GND
DOOR
SENS
KEY
ACT
O/P
3
OUTPUT 2
N.C. COM N.O.
By AE I PR OTE CT - O N SY STE MS
O/P
3
KOR A
O/P
DOOR
SENS
( – )
GND
DU
OUT
O/P 1.
INHIB
INT.
LOCK
OUTPUT 2
N.C.
COM N.O.
TAMPER
N.C.
EG
IN
DOOR BELL
N.O.
( + ) ( – )
12V DC
( + ) ( – )
DOOD LOCK
K OR A
KEY ALARM
DAP
ON OFF
3
1 - 2 : TAMPER N.C.
3 - 4 : DOOR BELL
5 - 6 : 12V DC --
7 - EG IN --
8 - 9 : OUTPUT 1 --
Fail-Secure Electric
Lock in Default
11 : OUTPUT 3
12 : K OR A O/P --
i) KEYPAD ACTIVE OUTPUT (K)
ii) ALARM OUTPUT (A)
●
●
●
●
●
●
●
CONNECTION TERMINALS
K OR A
KEY ALARM
4
13 : DOOR SENS --
NOTE:
1) Door Auto Re-lock
2) Door Forced Open Alarm and Warning
3) Door Propped-up Warning
4) Inter-lock Control
14 : GND (-) --
15 : DU OUT --
16 : O/P 1 INHIB. --
17 : INT. LOCK
●
●
●
●
●
5
13 : DOOR SENS --
NOTE:
1) Door Auto Re-lock
2) Door Forced Open Alarm and Warning
3) Door Propped-up Warning
4) Inter-lock Control
14 : GND (-) --
15 : DU OUT --
16 : O/P 1 INHIB. --
17 : INT. LOCK
THE LED INDICATORS
MAINS (AMBER)
DOOR (GREEN & RED)
ALARM (RED)
AUX (GREEN)
BACK LIGHTING
THE PACIFIER TONES & THE LED INDICATING SIGNALS
NOTE:
*
**
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
●
●
●
●
18 - 19 - 20 : OUTPUT 2
●
6
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing –
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording Duress Codes – (No Default Codes)
4) Recording the Visitor Codes – (No Default Codes)
STANDARD PROGRAMMING SUMMARY CHART
7
(Default: Momentary, 1-second for all 3 outputs)
(default = 1 second)
(default = 1 second)
(Default: Fail-Secure)
(Default: 10 tries / 30 seconds)
(default)
G) Door Forced-Open Alarm – (Default: Disabled)
(default)
(default=1 second)
8
DU
OUT
( )
GND
DU
OUT
19
The Duress Output will switch to ( ) ground when duress code is entered. You may use it to turn ON an LED
lamp and /orasmall buzzer to notifyaguard; or connect it toa24 hour Normally Open protection zone of an
alarm system.
-
Only one connection option is recommended. Make sure that the sink current does not exceed the maximum
rating of 100mA.
(D) DURESS OUTPUT
(E) OUTPUT 2
OR
1.5K
LED
+12V
LOW POWER
PIEZO BUZZER
ALARM CONTROL PANEL
24 HOUR N.O.
PROTECTION
ZONE
(i)Shunting an N.C. Zone
Use the Normally Open (N.O.) output contact to shuntaNormally Closed (N.C.) protection zone of an
alarm system.
Set output contact to Start/Stop Mode (Programming Option 51).
( ii)Alarm System Arm-Disarm Control
Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.
Consult your alarm control panel manual for the appropriate output contact to be used in arm-disarm control.
Usually set output2to Momentary mode (Programming Option 501) for multi station systems and Start
/ Stop mode (Programming Option 51) for single station systems.
OR
ALARM CONTROL PANEL
REMOTE
ARM-DISARM
CONTROL
NO. OR N.C.
N.C.
N.C. MAGNETIC CONTACT
TO PROTECTION ZONE
OF AN ALARM CONTROL PANEL
OUTPUT 2
N.C. COM N.O.
OUTPUT 2
N.C. COM N.O.
(Default: 1 long beep)
I) User Code Entry Modes (Auto or Manual) – (Default: Manual)
(Default: ON)
(default)
K) Main LED Flashing ON-OFF – (Default: Flashing)
L) Egress Delay & Warning – (Default: Instant, No warning)
(default)
M) Delay Time to Start Door Propped-up Warning – (Default: OFF)
(default)
N) Exit Programming Mode
(default)
(default)
(default)
9
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
SETTING & PROGRAMMING
DAP
ON OFF
10
New Master Code
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
System Refresh (Complete Data Refresh) (Refresh Code 8901)
11
User ID Entry of Code
Output 1
Output 2
Output 3
NOTE:
●
●00-99
●0-9
●
●
●
Programming Example :
3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
3. Program an User Code 5 4 3 2 1 for output 2 ------- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
4. Program an User Code 9 2 7 0 5 3 for output 3 ---- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
Operaon (Manual Code Entry Mode)
NOTE:
12
Super User Code
NOTE:
●
●
●
●
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
13
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●
REMARK :
●
●
●
●
●
●
3)
NOTE:
●
●
●
●
14
User ID Duress Code
NOTE:
●
●0-9
●
●
For example:1 3 5 7
3 3 5 7 1 3 5 8
●
●
Programming Example :
3 2 8 9
2. Program 3 3 5 7 as 1st Duress Code:
Program 2 3 9 8 0 as 2nd Duress Code --- if more user needs duress code:
Operaon :
NOTE :
●
●
15
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
16
Deleng Examples:
3289
a)
b)
c)
d)
e)
f)
17
Time Length
A)
B)
C)
D)
NOTE:
●
● and 53
● and 63
Programming Options for Outputs 1, 2 & 3 (See “Programming Summary Chart” Secon D for more
informaon) :
Example:
8 3 2 18 3
5 4 3 2 15 4
Example:
5 4 3 2 15 4 3
9 2 7 0 5 39 2 7
18
Operaon :
8 3 2 1
5 4 3 2 1
9 2 7 0 5 3
NOTE:
●The purpose of the accelerated Code --
●
Super User Code
Super User Code
Super User Code
Programming Examples:
3 2 8 9
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 2 in Start / Stop Mode:
4. Set Output 3 in Start / Stop Mode with 3-digit Accelerated Start Code:
19
Type of Lock
Programming Codes for Type of Locks:
Important Note to Installer:
de-energized
(Default)
energized
20
Table of contents
Other APO Keypad manuals
APO
APO DK-9826 MK-II User manual
APO
APO DK-9866 MK-II User manual
APO
APO DK-9823 MK-II User manual
APO
APO DK-9821 MK-II User manual
APO
APO DK-9350 User manual
APO
APO DK-9520 MK-II User manual
APO
APO DK-9865 MK-II User manual
APO
APO DK-9522 MK-II User manual
APO
APO DK-9820 MK-II User manual
APO
APO DK-9330 A User manual
