FE TP-A1 User manual

1
Instruction Manual
IP55 rating cover for
TP-A1 keypad “CTP-A1”
Thank you very much for purchasing the optional IP55 rating cover “CTP-A1” for TP-A1-XXX keypad.
This manual describes the installation procedure of this optional cover.By installing this cover with the
TP-A1-XXX keypad in the external surface of a switch cabinet, the keypad is protected from dust and water
splash, achieving IP55 ingress protection rating.
•Read through this manual in conjunction with the instruction manual of FRENIC HVAC, FRENIC AQUA, FRENIC Lift,
FRENIC Ace inverters and TP-A-XXX keypad,to become familiar with proper handling and correct use.
•Improper installation may result in not fulfilling IP55 rating. Please follow the installation procedures written in this manual.
•This cover can be used only in combination with TP-A1-XXX keypad. Do not attempt to use with other types, even from Fuji
Electric.
•Deliver this manual to the end user of this product.
•Failure to heed the information described in this manual may lead to a loss of any liability by Fuji Electric Europe GmbH.

Fuji Electric Europe GmbH IM-FEE-CTPA1-1001a-EN

2
1. Preliminary Checking
When opening the package of this product, check that:
§A plastic cover has been delivered with 2 gaskets and 2 metal positioners attached to the cover, as
shown in figure 1.
Figure 1. CTP-A1 cover appearance
§The cover has no apparent cracks or any deformation.
§4 fixing screws are already placed in the 4 fixing holes of the cover, as shown in figure 1.
These screws can rotate freely without falling apart.
§Metal positioners are in place.
Fixing screws
Gaskets
Metal positioner
Upper metal positioner
Fixing screws

3
2. Installation Procedure
1. Please refer to the drawing included in the Annex of this manual that describesthe installation holes of
the keypad and the optional cover CTP-A1.
2. Mark the holes on the surface where the keypad and cover will be installed, according to the drawing of
Annex I. One possible method is to attach this drawing to the surface of the panel. Please refer to figure
2abelow.
2a. Installation holes marked
2b. Installation holes drilled
Figure 2. Making the installation holes.
3. Drill the holes according to the diameters and tolerances described in the drawing of Annex. Refer to
figure 2b. After drilling, ensure that the surface is clean from shavings and remove the protection tape
(if any).
4. Ensure that the upper (small) metal positioner is loose by unfastening slightly the 2 fixing screws,as
shown in figure 3below.
Figure 3. Slightly unfastening the 2 screws of the upper metal positioner

4
5. Attach the TP-A1-XXX keypad to the CTP-A1 cover and move slightly down the upper metal positioner
until it interferes with the upper side of the keypad. Then fasten completely the 2 fixing screws, as shown
in figure 4below. Check that the keypad does not fall apart.
Figure 4. Fastening the 2 screws of the upper metal positioner
6. Attach the cover to the panel, as shown in figure 5.
Figure 5. Attaching the CTP-A1 cover.

5
7. Fix the CTP-A1 cover, by using the 4 M4 screws (already placed in the cover). Tighten the cover carefully
by using 4 M4 nuts and washers (not provided with the package), as shown in figure 6abelow. Tighten
the nuts until the gasket is completely compressed and can be hardly seen, as shown in figure 6bbelow.
The screws provided are suitable for a panel door thickness up to 2 mm. For panels thicker than 2 mm
please consult with Fuji Electric representative.
6a. Fixing nuts and washers (before fastening)
6b. Gasket compressed when fastened
Figure 6. Fixing CTP-A1 cover.
Procedure is completed. Figure 7 shows the appearance of the CTP-A1 cover after completing the installation.
Figure 7. CTP-A1 cover after completing the installation.

6
Annex
Installation holes drawing

7
Instruction Manual
IP55 rating cover for TP-A1 keypad “CTP-A1”
First Edition, May 2017
Copyright © 2017 Fuji Electric Europe GmbH
All rights reserved.
The purpose of this instruction manual is to provide accurate information about handling and installation of
CTP-A1 optional cover. Please feel free to send your comments regarding any errors or omissions you may have
found, or any suggestions you may have for generally improving the manual.
In no event will Fuji Electric Europe GmbH be liable for any direct or indirect damages resulting from the
application of the information in this manual.
All products and company names mentioned in this manual are trademarks or registered trademarks of their
respective holders.
The information contained herein is subject to change without prior notice for improvement.
No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Europe
GmbH.

8
Fuji Electric Europe GmbH
Goethering 58, 63067 Offenbach am Main, Germany
www.fujielectric-europe.com [e-mail]