Restoration Hardware NICCOLO Instruction manual

NICCOLO FLOATING FLOOR MIRROR 24" (61 CM) X 80" (203 CM)
ASSEMBLY A ND I NSTAL L AT I ON I NSTRUCT I ONS
ENGLISH

N I CCOLO F LOAT I NG FLOOR M I RROR 24" (6 1 CM ) X 8 0 " (203 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING FLOOR MIRROR 24" (61 CM) X
80" (203 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Bracket (2)
(C) Clevis pin (4)
(D) Hair pin (4)
(E) Stainless steel screw (4)
(F) Steel screw (10)
(G) EZ mini anchor (14)
(H) Buffer (4)
(I) Aluminum hanger (2)
(J) Metal cord (2)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 172 lbs (78 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B) (F)
(C)
(G)
(D)
(I)
(H)
(E) (J)

N I CCOLO F LOAT I NG FLOOR M I RROR 24" (6 1 CM ) X 8 0 " (203 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (I) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (G).
. Insert the EZ mini anchors (G) into the holes on the wall.
5. Mount the aluminum hanger (I) into the wall using screws (F).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (H) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
H
H
H
H
FG
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
G
Wall
F
I
Plywood frame
Backside
Backside

N I CCOLO F LOAT I NG FLOOR M I RROR 24" (6 1 CM ) X 8 0 " (203 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
LEANING
1. Move the mirror into position close to the wall. Mark locations on
the wall approximately 5" (13 cm) above the set of metal brackets
attached on mirror. Move mirror away from the wall. Drill pilot holes
with a 3/32" (0.2 cm) drill bit if needed. Install EZ mini anchors (G)
into the holes, and then attach brackets (B) to the wall with the
screws (E) provided. (Figure 1).
2. Move the mirror into it's final position, taking care to line up the wall
brackets with the mirror brackets. Attach the metal cord (J) into
bracket with clevis pin (C) and hair pin (D). (Figure 2).
3. Important: Check to ensure that the wall brackets are firmly screwed
into the wall, the mirror brackets are firmly attached to the frame.
**NOTE: When leaning the mirror, we recommend installing the Anti-Tip Kit. When hanging, simply follow the instructions above. The Anti-Tip Kit is not
necessary.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
FIGURE 1
FIGURE 3
G
B
E
Wall
FIGURE 2
FIGURE 4
D
C
I
Mirror
Wall
H
H
H
H
Backside

NICCOLO FLOATING FLOOR MIRROR 42" (107 CM) X 78" (198 CM)
ASSEMBLY A ND I NSTAL L AT I ON I NSTRUCT I ONS
ENGLISH

N I CCOLO F LOAT I NG FLOOR M I RROR 42 " ( 107 CM ) X 78 " ( 198 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING FLOOR MIRROR
42" (107 CM) X 78" (198 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Bracket (2)
(C) Clevis pin (4)
(D) Hair pin (4)
(E) Stainless steel screw (4)
(F) Steel screw (6)
(G) EZ mini anchor (10)
(H) Buffer (4)
(I) Aluminum hanger (1)
(J) Metal cord (2)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 99 lbs (44 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B) (F)
(C)
(G)
(D)
(I)
(H)
(E) (J)

N I CCOLO F LOAT I NG FLOOR M I RROR 42 " ( 107 CM ) X 78 " ( 198 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (I) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (G).
4. Insert the EZ mini anchors (G) into the holes on the wall.
5. Mount the aluminum hanger (I) into the wall using screws (F).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (H) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
H
H
H
H
FG
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
G
Wall
F
I
Plywood frame
Backside
Backside

N I CCOLO F LOAT I NG FLOOR M I RROR 42 " ( 107 CM ) X 78 " ( 198 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
LEANING
1. Move the mirror into position close to the wall. Mark locations on
the wall approximately 5" (13 cm) above the set of metal brackets
attached on mirror. Move mirror away from the wall. Drill pilot holes
with a 3/32" (0.2 cm) drill bit if needed. Install EZ mini anchors (G)
into the holes, and then attach brackets (B) to the wall with the
screws (E) provided. (Figure 1).
2. Move the mirror into it's final position, taking care to line up the wall
brackets with the mirror brackets. Attach the metal cord (J) into
bracket with clevis pin (C) and hair pin (D). (Figure 2).
3. Important: Check to ensure that the wall brackets are firmly screwed
into the wall, the mirror brackets are firmly attached to the frame.
**NOTE: When leaning the mirror, we recommend installing the Anti-Tip Kit. When hanging, simply follow the instructions above. The Anti-Tip Kit is not
necessary.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
FIGURE 1
FIGURE 3
G
B
E
Wall
FIGURE 2
FIGURE 4
D
C
I
Mirror
Wall
A
H
H
H
H
Backside