Restoration Hardware RH Teen Laguna User manual

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the
address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the bunk bed is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bunk bed is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
All Restoration Hardware Bunk Beds are designed to meet the highest safety
standards and comply with all U.S. and Canadian Bunk Beds regulations.
1
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
IMPORTANT SAFETY INFORMATION FOR BUNK BED
WARNING
1. Follow the information on the WARNINGS appearing on the upper bunk end
structure and on the carton.
2. Always use the specified size mattress, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from
damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement
parts.
10.Use of a night light may provide added safety precaution for a child using
the upper bunk.
11.Use guardrails on both sides of the upper bunk.
12.If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed: for example, but not
limited to, hooks, belts, and jump ropes
15.Keep these instructions for future reference.
16.DO NOT remove warning label from bed.
Never allow a child under 6 years on upper bunk.
Use only mattress which is 74"-75" long and 52 1
2" -
53 1
2" wide on upper bunk.
Ensure thickness of mattress does not exceed 6"
and mattress is at least 5" below upper edge of
guardrails.
Use guardrails on both sides of upper bunk.
Prohibit horseplay on or under bed(s).
Prohibit more than one person on upper bunk.
Use ladder for entering and leaving upper bunk.
STRANGULATION HAZARD - Never attach or hang
items to any part of the bunk bed that are not
designed for use with the bed; for example, but not
limited to, hooks, bells, and jumpropes.
To help prevent serious or fatal injuries from entrapment of
falls:
DO NOT REMOVE THIS LABEL
2
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
PARTS INCLUDED
A [2] HEADBOARD & FOOTBOARD
B1 [1] LONG GUARD RAIL
B2 [1] SHORT GUARD RAIL
C [1] STORAGE
D [1] LOWER SIDE RAIL
E [2] UPPER SIDE RAILS
F1 [5] BED SLATS (LONG)
F2 [3] BED SLATS (SHORT)
G1 [1] LOWER PLATFORM PANEL (NARROW)
G2 [1] LOWER PLATFORM PANEL (WIDE)
H [2] UPPER PLATFORM PANELS
I [1] LADDER
COMPONENT IDENTIFICATION AND HARDWARE
7
Flat Head Phillips Screw
(M4x20mm) 22 pcs.
8
9
10
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 12 pcs.
2Curved Washer 12 pcs.
3Lock Washer 20 pcs.
4
5Wrench 1 pc.
Hex Nut 12 pcs.
6
Allen Bolt
(M8 x 40mm) 8 pcs.
Round Head Screw
(M4x25mm) 64 pcs.
Plain Washer
Allen Key 1 pc.
Metal bracket 3 pcs.
11
13
Phillips Screwdriver
(Not included) 1 pc.
14
Concealed metal bracket 2 pcs.
Flat Head Phillips Screw
(M3x15mm) 4 pcs.
A
B1
C
D
E
H
H
F1
F2
I
G1
G2
8 pcs.
12
B2
A
3
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
IMPORTANT
These bed parts can be cumbersome and heavy, therefore the assistance of two or more people is recommended in order to prevent personal injury
and ensure the bed parts are not damaged during the assembly process.
ASSEMBLY INSTRUCTIONS
1. Lay the headboard and footboard (A) on a flat surface.
2. Attach the long guard rail (B1) to the headboard (A), same to so attach the short guard rail (B2) to the footboard (A). Refer to FIGURE 1.
3. Attach the threaded rods (1) into the fixed nuts in the post of the headboard/footboard by turning them manually. See FIGURE 2 and FIGURE 3.
NOTE: The Short guard rail can be installed at either end of the Headboard or Footboard depending on your desired ladder location. When Short
guard raill (B2) install into the left of the Headboard or Footboard, refer to option A & B. In the opposite way, the guard rail will install into the right
of the Headboard or Footboard, refer to option C & D.
10
12
FIGURE 1
OPTION A OPTION B
OPTION C OPTION D
FIGURE 2
1
FIGURE 3
1
Fig.1
Fig.2
Fig.1
Fig.1
Fig.1
Fig.2
Fig.3
Fig.3
A
A
4
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
4. Fully remove all the drawers out of the storage (C). Attach the storage to the headboard (A/B1), as per illustration in FIGURE 4, FIGURE 5.
5. Attach the lower side rail (D) to the headboard as per illustration in FIGURE 6.
NOTE: Side panel is exchangeable for ladder placement on either side.
6. Bring the upper side rail (E) in upright position and align the threaded rods on the headboard to the corresponding holes in the end of the upper side
rail. Attach the upper side rail to the headboard, as in FIGURE 7. KEEP HOLDING THIS SIDE RAIL DURING NEXT STEP.
7. Repeat step 6 to attach the other upper side rail to the headboard. KEEP HOLDING BOTH UPPER SIDE RAILS DURING NEXT STEP.
C
B1
E
D
Fig.4
Fig.5
Fig.6
Fig.7
FIGURE 4
FIGURE 5
FIGURE 7
6
3
7
8
2
3
4
5
6
3
78
FIGURE 6
A
E
5
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
8. Align the threaded rods on the footboard (A/B2) to the corresponding holes at the end of the storage (C), lower side rail (D) and upper side rails
(E). Align the locator pins on the end of the storage and the side rails to the corresponding holes in the footboard. Insert the footboard into the
storage and the side rails.
9. Repeat step 4, 5, 6 and 7 to attach the storage and the side rails to the footboard.
E
A
D
B2
C
B1
A
6
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
10. Attach the Metal bracket (11) into the side rails and guardrails. Insert screw (10) provided to pass through hole on metal bracket (11) to the pre-drill
hole on side rails and guardrails. Refer to FIGURE 8.
11
10
FIGURE 8
7
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
11. Set the bed slats (F1, F2) on the upper bunk and lower bunk. Secure each slat by using screws (9) provided. See FIGURE 9.
12. For the purpose assembly, the both of Concealed metal bracket (12) were removed and put on hardware pack. At the headboard and footboard
have the holes pre-drilled, this is location of the ladder that you will install. Please determind the location of the ladder for your desired, then install
the Concealed metal bracket (12) into the holes pre-drilled and secure it by Phillips screws (13) provided. Refer to FIGURE 10.
13
FIGURE 10
Fig.10
Fig.9
9
Fig.9
F1
F2
FIGURE 9
8
Page

L A G U N A F U L L O V E R F U L L B U N K B E D I N S T R U C T I O N S
13. Hook the ladder (I) on the footboard simultaneously align the metal concealed bracket male on the ladder with the female bracket on the
footboard, Use screw (10) provided to fix the top of ladder with footboard. as per illustration in FIGURE 11 and FIGURE 12.
14. Place the platform panels (G1, G2, H) on the lower bunk and the upper bunk, then fix them with screws (9). See FIGURE 13.
15. Return the drawers to the storage. Assembly is complete.
Fig.12
Fig.11
H
H
G2
G1
Fig.13
Fig.13
10
no screw
FIGURE 12
FIGURE 11
FIGURE 13
9
9
Page