retrotouch RTS2030 User manual

INSTALLATION WARNINGS:
BEFORE COMMENCING INSTALLATION ISOLATE YOUR MAINS ELECTRIC SUPPLY
Read the instructions care fully before starting the installation process and keep them for future reference.This product must be
installed by a qualified electrician.This product should be installed in accordance with the relevant sections of the building regulations
code, and the current edition of the IEE Wiring Regulations (BS 7671:Requirements for electrical installations) and appropriate
statutory regulations.
Do not exceed the Maximum Power Rating detailed in the s.pecification over leaf.
Installation
Remove the glass panel of a
touch remote switch: Using a small
flat screwdriver remove the front
cover by placing the screw driver in
the location notch on the bottom
part of the cover and twist to unclip
the cover.
Wiring: Wire as described in the diagram opposite. Push
wires firmly into terminals and tighten terminal screws so that
wires are held securely. No bare wires should protrude from the
terminals. Ensure correct wires are connect to the correct
terminals, if incorrectly wired, this could damage the switch.
Fix screws: Use the screws supplied to attach switch to
backbox using a flat head screwdriver
Reattach the glass panel: Align the glass panel over the
switch and firmly push to click into place.
Power on: Once the power is on, wait 2 minutes for the
switch to power up, then touch the panel to turn on the light.
The remote (RTS2030 remote models only)
Pairing a remote
1.Touch & hold the dim down touch
area of the switch for 5 seconds and
wait for the beep.
2. Press and hold a button A (for 1
gang) or B (for 2 gang) on the remote
control and release after you hear a
beep.
Un-registering a remote:
Repeat steps for registering the remote.
When pressing and holding the remote
button, wait for two beeps and the
remote will be un-paired.
Factory reset: Press and hold the
switch for 5 seconds till you hear a
beep, continue to hold for a further 8
seconds until you hear another beep.The switch is now
back to factory settings.
twist to remove
75 3mm
60mm
75 3mm
INSTRUCTION MANUAL RTS2030
AB
C
For support visit www.retrotouch.com/support
lock here
first
Push
until click
Optional scene remote available, Can control up to 19
gangs and set up to 4 scenes.

RTS2030
For support visit www.retrotouch.com/support Retrotouch, PO Box 1099, Worth, Crawley, RH10 OAD
Tel: [phone] Fax: [phone] [e-mail] www.retrotouch.co.uk
RTS2030
INSTRUCTION MANUAL
LL 1
Neutral
Lamp
Live
LL 1 L 2
Neutral
Lamp
Lamp
Neutral
Wiring diagrams
1 Gang model 2 Gang model
Live
Guarantee
All items purchased, come with a 1 year warranty (from date of purchase). Please keep proof of purchase.
If any of our products become faulty within this 1 year period, please contact us. Please send product/s by recorded post,
as proof of dispatch as we cannot be held liable for products lost in the post. If the product is found to be faulty, a
replacement shall be sent within 7 working days from date received. In all cases, an identical replacement shall be sent,
however, if the product has been discontinued a suitable alternative shall be sent with the same or similar specification.
57mm
63mm
86mm
86mm
52.6mm
27mm
10mm
Specification
Voltage: 220~240V ~ 50/60Hz
Operating Power:
1 Gang (1-300W),
2 Gang (1- 600W),
Working Temperature: 0oC~40oC
Relative Humidity: 10% - 93%
Energy Consumption: <0.02W
Measurement: 86x86mm
Backbox depth: 35mm
life: 100,000 times at least (relay useful life)
Remote usage distance >20M
Remote battery: 27A 12vDC
Battery life : 1 year (dependent on usage)
Power: < 0.1mW
CE & RoHS Certified
TO TURN ON
Tap once around the circle
to turn on. Double tap to
go to max brightness
TO TURN OFF
Touch the switch panel
the circle to turn off
Using the dimmer
AB
C
USING THE REMOTE
Press A (for one gang) B (for two gang), light
turns on, press again to turns the light off.
press C or to dim up and down.
A = 1 gang
B = 2 gang
C = Dim up
= Dim down
DIM UP & DOWN
Touch & hold the down
arrow to dim down and the
up arrow to dim up.
Features
Microline Glass Panel
Touch & Remote control
Memory dimming feature (Remembers last
lighting setting)
Auto gradual dim up/down on power on/off.
Remote control upto 20m (RF 433Hz)
Background light (with indicator light)
Chrome surround
Trailing Edge Dimmer
Works with LED’s, Halogens, standard bulbs.
1010