Rev-a-shelf Ml-450sc-ws-1 User manual

This is a spring loaded

product that can cause

severe harm if not handled

properly during installation.

WARNING

TOOLS REQUIRED:

30–45 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

• Clean with a damp cloth and

wipe parts dry

• Lubricate pivot points as

needed

HEAVY DUTY APPLIANCE LIFT

A. B.

LEFT & RIGHT

Parts List

No. Description Qty

A 10 g x 16 mm Wood Screws 16

B 10 g x 13 mm Wood Screws 12

C Side-Mounting Brackets (L & R) 2

D Shelf 1

INSTALLATION INSTRUCTIONS: HEAVY DUTY APPLIANCE LIFT I-MLWHSHELF-0118

FIGURE A

A. Mark and pre-drill (2) 3 mm pilot holes

13 mm deep into the side support panel.

B. The rst hole should be 32 mm from

the front of cabinet and 114 mm down

from the top of the cabinet.

C. The second hole is parallel to the rst

hole location 267 mm toward rear of

cabinet.

D. Mount the side mounting bracket to

the cabinet support panel by aligning the

back middle hole and the front slot with

the holes that were pre-drilled.

E. Fasten with (2) 10 g x 16 mm wood

screws. Repeat this step for the other

side mount bracket. Wait until Step 5

to install the remaining screws in the

mounting plates to ensure the shelf

surface is level with mixer weight.

NOTE: The distance from top of

cabinet is determined by height and

length of the accessory. 114 mm will

allow adequate clearance for 419 mm

tall stand mixers. Side mounts can be

positioned higher if using lift for smaller

appliances.

STEP 1

INSTALLING SIDE

MOUNTING BRACKETS

DRILL 3 mm PILOT HOLES

267 mm

32 mm

114 mm

ENSURE PROPER

ALIGNMENT

USING A LEVEL

COUNTER TOP

STEP 2

MOUNTING THE

APPLIANCE LIFT SHELF

NOTE: Holes are pre-drilled to

ensure proper function of the

appliance lift.

From underneath the shelf, line-up the

pre-drilled holes in the shelf with the

slotted holes on the mounting plates.

Insert (6) 10 g x 13 mm wood screws into

the pre-drilled holes, but do not fully

tighten.

(See Fig B).

INSTALLATION INSTRUCTIONS: SHELF MOUNTING WORKSHEET

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

SHELF MOUNTING WORKSHEET

I-MLSHELF18-1017

NOTE: Holes are pre-drilled to

ensure proper function of the

mixer lift.

From underneath, line-up the

pre-drilled holes in the shelf with

the slotted holes on the mounting

plates. Insert (6) #10 x 1/2” wood

screws into the pre-drilled holes,

but do not fully tighten.

(See Fig A).

Adjust shelf side edges so they are

over the 90-degree bend of the

mounting plate and tighten screws

(See Fig B).

Note: Shelf cannot extend

past the outer surface of the

mounting plate.

This worksheet is for installing

Rev-A-Shelf’s maple or walnut

shelves to their appropriate mixer

lift mechanisms.

Note: Mixer Lift mechanism and

screws packaged separately.

Maple shelf is 11-3/4” x 20” and

designed for 18” face frame

cabinets.

Walnut shelf is 13-1/4” x 20”

and designed for 18” frameless

cabinets.

MOUNTING THE MIXER

LIFT SHELF

STEP 1

STEP 2

From underneath attach (6)

additional #10 x 1/2” (12 mm)

wood screws to remaining

(non-drilled) hole locations to

complete installation.

STEP 3

UNDERSIDE OF

MIXER LIFT SHELF

FRONT EDGE OF

MIXER LIFT SHELF

76 mm

216 mm

30 mm

508 mm

PRE-DRILLED HOLE

LOCATIONS

Mounting plate

outer surface

90° bend

327 mm

FIGURE B

Place a level on the shelf when

fully extended. With one hand

supporting the shelf, loosen the

screw in the front slots on each of

the cabinet mounting brackets.

The shelf surface should be “nose

up” until the appliance is added.

Once weighted, the shelf will

level out (See Fig D). Once in the

desired location, tighten the front

screws.

Place the appliance on the lift and

check for level in both directions.

Once satised, fasten the (12)

10 g x 16 mm wood screws into

the additional locations on side

mount brackets.

LEVEL ADJUSTMENT

Adjust shelf side edges so they are

over the 90-degree bend of the

mounting plate and tighten screws

(See Fig C).

Note: Shelf cannot extend

past the outer surface of the

mounting plate.

FIGURE D

STEP 3

STEP 5

LOOSEN SCREW

ADJUST VERTICALLY

INSTALLATION INSTRUCTIONS: SHELF MOUNTING WORKSHEET

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

SHELF MOUNTING WORKSHEET

I-MLSHELF18-1017

NOTE: Holes are pre-drilled to

ensure proper function of the

mixer lift.

From underneath, line-up the

pre-drilled holes in the shelf with

the slotted holes on the mounting

plates. Insert (6) #10 x 1/2” wood

screws into the pre-drilled holes,

but do not fully tighten.

(See Fig A).

Adjust shelf side edges so they are

over the 90-degree bend of the

mounting plate and tighten screws

(See Fig B).

Note: Shelf cannot extend

past the outer surface of the

mounting plate.

This worksheet is for installing

Rev-A-Shelf’s maple or walnut

shelves to their appropriate mixer

lift mechanisms.

Note: Mixer Lift mechanism and

screws packaged separately.

Maple shelf is 11-3/4” x 20” and

designed for 18” face frame

cabinets.

Walnut shelf is 13-1/4” x 20”

and designed for 18” frameless

cabinets.

MOUNTING THE MIXER

LIFT SHELF

STEP 1

STEP 2

From underneath attach (6)

additional #10 x 1/2” (12 mm)

wood screws to remaining

(non-drilled) hole locations to

complete installation.

STEP 3

UNDERSIDE OF

MIXER LIFT SHELF

FRONT EDGE OF

MIXER LIFT SHELF

76 mm

216 mm

30 mm

508 mm

PRE-DRILLED HOLE

LOCATIONS

Mounting plate

outer surface

90° bend

327 mm

STEP 4

From underneath the shelf, attach

(6) additional 10 g x 13 mm wood

screws to remaining (non-drilled)

hole locations to complete

installation.

FIGURE C

FIGURE F

266 mm

56 mm

570 mm

TENSION

ADJUSTMENT

30 mm

32 mm

IDEAL

MEASUREMENTS

446 mm

39 mm

475 mm

114 mm

112 mm

LOWEST POINT

This appliance lift is equipped

with (3) adjustable spring tension

settings for 0-9 kg, 9- 13 kg, and

13-27 kg. The unit is shipped

with the spring settings set to

the middle setting. To adjust

tension, remove set bolt with a

10 mm open end wrench.

NOTE: DO NOT release holding

tension until after the set bolt

is in the desired location. With

the bolt removed, adjust to the

desired setting. Reinstall the

set bolt, and tighten securely.

Repeat with the opposite side

mounting bracket.

STEP 6

ADJUSTING APPLIANCE

LIFT SPRING TENSION

(REFER TO FIGURES E & F)

FIGURE E

1) 0–9 kg

2) 9–13 kg

3) 13–27 kg

RECOMMENDED SPRING

POSITION FOR VARYING

MIXER WEIGHT

Anything over 27 kg

will void the warranty.

! !

WARNING

RELEASING THE 12 MM BOX END WRENCH BEING USED TO HOLD

THE SPRING-LOADED SIDE-MOUNTING BRACKETS BEFORE SECURELY

FASTENING THE REMOVED BOLT CAN CAUSE SERIOUS INJURY

Other Rev-A-Shelf Indoor Furnishing manuals

Rev-A-Shelf

Rev-A-Shelf 4PIL-TRI-0216 User manual

Rev-A-Shelf

Rev-A-Shelf CVRI Series User manual

Rev-A-Shelf

Rev-A-Shelf 5CCSO Series User manual

Rev-A-Shelf

Rev-A-Shelf 4SH-15-1 User manual

Rev-A-Shelf

Rev-A-Shelf 4WKB-1 User manual

Rev-A-Shelf

Rev-A-Shelf RSLD-4BW-062 User manual

Rev-A-Shelf

Rev-A-Shelf Glideware User manual

Rev-A-Shelf

Rev-A-Shelf CRC-36CR User manual

Rev-A-Shelf

Rev-A-Shelf 445 Series User manual

Rev-A-Shelf

Rev-A-Shelf Wood Classics 447 Series User manual

Rev-A-Shelf

Rev-A-Shelf RV Series User manual

Rev-A-Shelf

Rev-A-Shelf GRP21891 User manual

Rev-A-Shelf

Rev-A-Shelf 448 Series User manual

Rev-A-Shelf

Rev-A-Shelf Closet User manual

Rev-A-Shelf

Rev-A-Shelf WLS Series User manual

Rev-A-Shelf

Rev-A-Shelf CO Series User manual

Rev-A-Shelf

Rev-A-Shelf 4WCDM Series User manual

Rev-A-Shelf

Rev-A-Shelf 548 Series User manual

Rev-A-Shelf

Rev-A-Shelf 1550DM1-343-FL User manual

Rev-A-Shelf

Rev-A-Shelf 9" Two-Tier Basket User manual

Rev-A-Shelf

Rev-A-Shelf 5300 Series User manual

Rev-A-Shelf

Rev-A-Shelf 448TP User manual

Rev-A-Shelf

Rev-A-Shelf 4WDBSC Series User manual

Rev-A-Shelf

Rev-A-Shelf CHDSL-996-SN-1 User manual

Popular Indoor Furnishing manuals by other brands

Regency

Regency LWMS3015 Assembly instructions

Furniture of America

Furniture of America CM7751C Assembly instructions

Safavieh Furniture

Safavieh Furniture Estella CNS5731 manual

PLACES OF STYLE

PLACES OF STYLE Ovalfuss Assembly instruction

Trasman

Trasman 1138 Bo1 Assembly manual

Costway

Costway JV10856 manual

moss DESIGN

moss DESIGN Caisson Credenza Assembly instructions

Aquaglide

Aquaglide FULL DECK 15.0 owner's manual

AREBOS

AREBOS AR-HE-SW30 user manual

Till-Hilft

Till-Hilft Fulda 87005.330 Assembly instructions

Twoey Outside

Twoey Outside 2010 quick start guide

Hettich

Hettich Easys 200 operating instructions

The bedboss

The bedboss RELAX 404 Series owner's manual

Oeseder Möbelindustrie

Oeseder Möbelindustrie Bern 991 720 Assembly instructions

Costway

Costway HW68469 user manual

Next ALIX A27743 Assembly instructions

BROSA

BROSA Hans Assembly guide

Prodigg

Prodigg MINIKA PBA015T-FUR installation manual

Rev-A-Shelf ML-450SC-WS-1 User manual

Popular Indoor Furnishing manuals by other brands