REVELL KIT 1742 User manual

®
Á LIRE AVANT DE COMMENCER
• DÉGAGGEZ UN ESPACE POUR
TRAVAILLER.
• ÉTUDIEZ LES ÉTAPES DE MONTAGE
AVANT DE COMMENCER.
• CHAQUE PIÉCE EN PLASTIQUE PORTE
UN NUMÉRO DE PIÉCE.
• LISEZ LA RE MARQUE CONCERNANT
L´APPLICATION DES AUTO-COLLANTS,
´A L´ ÉTAPE 7 .
MISE EN GARDE:
POSITIONNEZ AVEC PRÉCAUTION
TOUTES LES PIÉCES DE CE MODÉLE
RÉDUIT, CAR VOUS NE POUVEZLES
EMBOîTER QU’UNE SEULE FOIS.
SHERMAN TANK
85174210200
READ BEFORE YOU BEGIN
• CLEAR A SPACE TO WORK ON
• STUDY THE ASSEMBLY DRAWINGS
BEFORE YOU BEGIN
• EACH PLASTIC PART IS IDENTIFIED BY
A PART NUMBER
• SEE NOTE ABOUT APPLYING
STICKERS IN STEP #7
CAUTION:
POSITION ALL PARTS IN THIS KIT
CAREFULLY. PARTS WILL ONLY SNAP
TOGETHER ONCE.
KIT 1742
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* APPLY STICKER
* APPLIQUEZ LES AUTO-COLLANTS
The Sherman M4A1 rock-
et launcher tank had a
cast iron hull and earned
the nickname “Sreamin
Mimi” from the shriek-
ing sound the missles
made as they left the “Cal-
liope” rocket launcher.
Your Revell model has
a movable turret, cannon
and launcher and rolls on
hidden wheels. Also in-
cluded is a scale U.S Army
Jeep with motorcycle and
three soldier gures and
authentic military peel
and stick decal markings.
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.
If you have any questions or comments, call our hotline at: [phone]
or, please write to:
Revell Inc Consumer Service Department, 1840 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85174210200), part number, description, your return address and phone number.
Visit our website: www.revell.com

Step 1
Step 2
1
HULL
TOP
2
HULL
BOTTOM
3
HULL
REAR
4
WHEEL
5
TREADS
6
WHEEL
7
TREADS
KIT 1742 Page - 1

Step 3
Step 4
8
CUPOLA
BOTTOM
10
CUPOLA
9A
CUPOLA
PIVOT
9
CUPOLA
PIVOT
12
CANNON
SHEILD
11
CANNON BARREL
13
MACHINE
GUN
15
ROCKET SIDE SUPPORT
14
CANNON
PIVOT
KIT 1742 Page - 2

1
13
2
Step 7 Sticker Placement Guide
NOTE: When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly
to lift edge of sticker & use a fingernail to lift sticker from sheet. Line up sticker on body and carefully press an edge
into place, slowly working sticker with a fingernail until sticker is fully on model.
REMARQUE : Pendant l’application des autocollants, éviter de toucher à la face collante pour ne pas laisser d’empreintes.
Plier légèrement la feuille d’autocollants pour relever le bord d’un autocollant, et le détacher de la feuille avec le
bout d’un ongle. Aligner l’autocollant sur la carrosserie, appuyer pour coller un de ses bords, et continuer de
l’appliquer lentement du bout de l’ongle jusqu’à ce qu’il soit complètement collé sur le modèle réduit.
Step 5
Step 6
TURN TURRET TO RAISE AND
LOWER GUN AND ROCKET
LAUNCHER
16
SHORT ROCKET
TUBES
BOTTOM
18
SHORT
ROCKET
TUBES
TOP
17
PIVOT
ARM
19
TUBE
SUPPORT
21
LONG
ROCKET
TUBES
TOP
20
LONG ROCKET
TUBES BOTTOM
COMPLETED ROCKET
ASSEMBLY
REPEAT fOR
OTHER SIDE
KIT 1742 Page - 3