Reverie 7T User manual

Reverie 7T™Power Base
Owner’s Manual and Reference Guide
REV: 2016-05-11
Manual Part No. D1103-301-7T
Copyright © 2016. All Rights Reserved.
Ascion LLC.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
2
Reverie 7T Power Base
Table of Contents
Safety Precautions.............................................................................................3
Parts List............................................................................................................9
Power Base Assembly Instructions ..................................................................10
App User Guide ...............................................................................................14
Wireless Remote Control...................................................................................17
Remote Control Operation Guide......................................................................18
Bluetooth®Pairing (Replacement Remote Control)...............................................20
Remote Control Emergency Power Down Feature............................................22
Troubleshooting.................................................................................................23
Warranty.............................................................................................................25
Warranty Information: Please see the warranty that came with your
product. Reverie 7T Power Base

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
3
Safety Precautions
SAFETY PRECAUTIONS
WARNING! IMPORTANT SAFETY INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY
BEFORE USING THIS PRODUCT.
SAVE THESE INSTRUCTIONS!
When using an electrical furnishing basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS FURNISHING)
DANGER: To reduce the risk of electric shock:
Always unplug this furnishing from the electrical outlet before cleaning.
WARNING:
To reduce the risk of burns, re, electric shock, or injury to persons:
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by or near children, invalids or
disabled persons.
• Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
• Never operate this furnishing if it has a damaged cord or plug, or if it is not working properly,
dropped or damaged, or dropped into the water. Return the furnishing to a service center for
examination and repair.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint,
hair and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not place remote in water or area of intense heat.
• Do not lift bed by wooden side rails.
• Excessive dropping of the remote may cause performance issues.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
4
Safety Precautions
WARNING: Risk of Injury:
Keep children away from extended foot support (or other similar parts).
WARNING: Risk of electric shock:
Connect this furnishing to a properly grounded outlet only.
See Grounding instructions.
GROUNDING INSTRUCTIONS:
This product must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER:
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or serviceman if you are in doubt as to whether the product is
properly grounded.
Do not modify the plug provided with the product. If it will not t the outlet, have a proper outlet
installed by a qualied electrician.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
5
Safety Precautions
This product is for use on a standard 120-volt circuit, and has a grounding plug that looks
like the plug illustrated in photo A (see Figure). A temporary adapter that looks like the
adapter illustrated in photo B and C can be used to connect this plug to a 2-pole receptacle
as shown in photo B if a properly grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet (photo A) can be installed by a
qualied electrician. The green colored rigid ear, lug or the like extending from the adapter
must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a metal screw.
This product is for use on a circuit having a standard rating of 120 volts and is factory equipped
with a specic electric cord and plug to permit connection to a proper electric circuit. Make sure
that the product is connected to an outlet having the same conguration as the plug. No adapter
should be used with this product. If the product must be reconnected for use on a different type of
electric circuit, the reconnection should be made by qualied service personnel.
Unauthorized modications could void the electrical portion of your warranty. Failure to use a
properly grounded outlet for this product or modication of the plug will compromise this important
grounding safety feature and may result in electrical shock, electrical re, or faulty operation of the
product.
FOR BEST RESULTS, YOUR POWER BASE SHOULD BE PLUGGED INTO A SURGE
PROTECTOR (not included).
WARRANTY PRECAUTION:
Do not open control box, motors or wireless remote controls (with the exception of the battery
compartment if equipped). The warranty is void if these units are tampered with. Any repair or
replacement of power base parts must be performed by an authorized technician.
IN-HOME USE AND HOSPITAL DISCLAIMER:
Your power base is strictly designed for in-home use only. It is NOT designed for hospital use
and is NOT designed to meet hospital standards. Do not use this base with TENT TYPE oxygen
therapy equipment or near explosive gases.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
6
Safety Precautions
WARNING!
DO NOT USE NEAR PEOPLE USING OR WEARING MEDICAL DEVICES. FOR HOUSEHOLD /
RESIDENTIAL USE ONLY. DO NOT USE OUTDOORS.
This product conforms to UL STD 962
IMPORTANT SAFETY FEATURES:
Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
If there is an overload weight condition on the head or foot mechanism, the control unit will
automatically stop all functions. Once the excess weight is removed the control unit will
automatically allow all functions to resume operation after 30 seconds.
As with any product that produces a vibrating motion, it is possible that some pacemakers may
interpret this motion as a false sense of movement and/or exercise. This may or may not affect
your pacemaker. If you have any concerns, please consult your physician. For more information
please contact customer service by calling 800-973-8374.
USER-SERVICEABLE PARTS:
This product is specically designed to have no maintenance by you, the user. Therefore, you are
encouraged not to open any motors, alter the wiring, adjust, modify or change the structure of the
product, as it will void the warranty.
POWER RATINGS:
INPUT: AC 120V - 60Hz, 1Amp
OUTPUT: DC 24V-3A
FUSE: 1.5A 250V
The input transformer voltage is AC120V (1.5 Amp) 60HZ, and the output voltage is DC24V
(3Amp). When there is a short-circuit, a fuse on the transformer will be blown in order to protect
the electrical equipment (Fuse: 1.5A). Should the above situation occur, the customer should
seek professional assistance by calling a licensed electrician or by contacting customer service at
800-973-8374.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
7
Safety Precautions
SMALL CHILDREN AND PETS WARNING:
After your Reverie 7T Power Base has been unboxed, immediately dispose of packaging as it can
smother small children and pets. To avoid injury, children and pets should not be allowed to play
on or under the power base.
Children should not operate this product without adult supervision. Close supervision is necessary
when this furnishing is used by, or near children, invalids, or disabled persons.
SAVE THESE INSTRUCTIONS:
Your Reverie 7T Power Base has been designed to provide you with the reliable
operation and durability you expect. This product has been inspected and tested prior to shipment.
RADIO FREQUENCY IS 433.92 MHZ
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void the user’s authority to
operate the device.
PRODUCT RATINGS
The lift motor in your Reverie 7T Power Base is NOT designed for continuous use. Reliable
operation and full life expectancy will be attained as long as the lift motor does not operate more
than two (2) minutes over an eighteen (18) minute period, or approximately 10% duty cycle. Any
attempt to circumvent or exceed this rating will shorten the life expectancy of this product and may
void the warranty. The recommended weight restrictions for your Reverie 7T Power Base is up to
850 lbs. total weight, including people and the mattress for all sizes of power bases. Lift speed will
vary due to weight and mattress conguration, as well as the mattress type. The weight must be
evenly distributed across the power base. This Product is not designed to support or lift 850 lbs of
total weight in the head or foot sections of your Reverie 7T power base alone, or in any unevenly
distributed fashion. Some mattresses are not designed for Power Bases because they do not
bend or ex well when adjusted. When using such a mattress with your Reverie 7T Power Base
the weight limits set forth herein do not apply, as the bending of the mattress requires signicant
force and puts signicant strain on the motors and the Power Base itself.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
8
Safety Precautions
Note: Exceeding the recommended weight restrictions could damage your power base
and void your warranty and using a mattress on top of your power base that is
not designed for adjustability may also void your warranty.
For best performance, you should enter and exit the Power Base while it is in the at or fully
lowered position.
DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION.
INTENDED USAGE
The electric power base should be installed with the head board brackets and/or the head
of the frame positioned close to a wall.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
9
Parts List for Reverie
7T Power Base
Note: Before discarding any packing materials, check the power base carton and verify the
following items in the parts list are included:
PARTS LIST
A. Wireless Remote Control (1)
B. Mattress Retainer Bracket (2)
C. Base Legs (4)
D. Inner Headboard Bracket (2)
E. Outer Headboard Bracket (2)
F. Retainer Bar Bolt (4)
G. Inner Headboard Bracket Bolt (4)
H. Outer Headboard Bracket Bolt (4)
I. Retainer Bar Plate (4)
J. 5/16 Inch Washer (16)
K. 5/16 Inch Locking Nut (8)
L. Allen Key ( 1)
M. Wrench (1)
N. 9-Volt Batteries (2)
O. 5V 1A Wall Charger Adaptor (1)
A. C.B.
E.
H.G. I.
D. F.
J.
M.
K.
N. O.
L.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
10
Power Base Assembly Instructions
IMPORTANT UNPACKING INSTRUCTIONS
To avoid damage to the power base, always
open the carton while the power base is
laying in the FLAT position on the oor.
OPEN FLAT
STEP 1
STEP 1A
Carefully lift the power base unit out of the
shipping carton, keeping the unit top side
down. For safety reasons, this should be
performed by 2 people.
Remove Head/Foot end rails
· Loosen cam lock at both corners.
· Loosen and remove hardware [bolts/nuts]
from the two inside slide brackets of each rail.
[see gure 1A,1B, and 1C]
· Gently detach the head and foot rails.
Remove Side rails
· Loosen and remove hardware [bolts/nuts]
from the two inside U brackets of each rail
[see gure 1D and 1E]
· Gently detach the side rails
NOTE: THIS IS AN OPTIONAL STEP.
If the customer wants to t this bed base
inside their own bed frame, then remove all 4
side rails. If the customer does not want this,
then proceed to STEP 2.
Figure 1A
Figure 1C
Figure 1B
Figure 1D
Figure 1E

11
Power Base Assembly Instructions
STEP 3
STEP 4
STEP 5
STEP 2
Remove and extend the power cord from the
frame.
Remove the plastic packaging from the power
base.
Carefully rotate the power base over to the
topside up position, resting on all 4 legs.
Assembling power base legs: Open the
accessories box, take out the 4 legs,
and thread them in a clockwise direction into
the threaded holes in the frame.
NOTE: Tighten the legs securely to the frame.
Leave no space between the leg and frame.
WARNING:
POWER CORDS MUST NOT INTERFERE
WITH ANY POWER BASE MECHANISMS.
ATTENTION! Improper handling
DO NOT
lean the power base
against the installed
legs to ip it over.
CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
STEP 6
Plug the power cord into a grounded electrical
outlet.
NOTE: An electrical surge protection unit is
recommended (not included)
STEP 7
Briey activate all functions on the wireless
remote control to verify that all of the features
are operational. If your Reverie 7T Power
Base does NOT operate, please refer to the
Troubleshooting section beginning on page
23 of this manual.
NOTE:
ProGrip™ is a material
feature on the foot end
of the power base that
prevents the mattress
from sliding off the base
when operating the head
and foot lifts.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
12
STEP 10
Install the headboard brackets to the power
base. Place one bracket on the left-hand side
of the power base and one bracket on the
right-hand side of the power base.
NOTE: If the power base is to be set
up without a headboard, simply install a
mattress on the frame. If a headboard is to
be installed, proceed to step 10.
NOTE: It is important to position the bottom
of the headboard cross member a maximum
distance of 3 inches (76.2 mm) between the
headboard and the top of the mattress. Do
not exceed 3 inches (76.2 mm).
ATTENTION: For any King/Split King
conguration, do not add center retainer
bars for either base on head or foot.
When two Twin XLs or two Split California
Kings are put together, DO NOT install
retainer bars in the center head or center
foot sections of the bases.
Power Base Assembly Instructions
STEP 8
STEP 9
DO NOT NEED RETAINER BARS.
Only install at the customers request.
Customers should try the ProGrip feature rst
without corner retainer bars. If they nd there
are issues with the mattress not staying on the
base when elevated then we recommend the
customer installing 2 retainer bars at the foot
end of bed. See STEP 9 to install the corner
retainer bars.
Use the Retainer Bolts (F) and Retainer
Bar Plate (I) to fasten the Mattress Retainer
Bracket (B) to the power base.
NOTE: Use only a manual screwdriver to
install the retainer bolts. DO NOT use a
power screwdriver to tighten the bolts. DO
NOT over tighten the mattress retainer
hardware.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
13
Power Base Assembly Instructions
Headboard Bracket Installation
STEP 11
1. Use the remote control to raise the head of
the base in order to gain access to the power
base frame.
2. Remove plastic cap and place the Inner
Headboard Bracket (D) into the round tube
frame making sure the bracket inserted into
the round tube. This will create a box shape.
Place the Headboard Bracket Bolt (G) with a
5/16 Inch Washer (J) through the pre-drilled
hole in the round tube frame and pass it
through the Inner Headboard Bracket. Use
the 5/16 Inch Washer (J) and the 5/16 Inch
Bracket. Use the 5/16 Inch Washer (J) and
5/16 Inch (K) and tighten the bolt in place.
Repeat for the opposing side of the power
base frame.
3. Place the open side of the outer headboard
bracket (E) onto the exposed square tube
of the inner headboard bracket (D). This will
create a tight t between (D) and (E). Place
a Headboard Bracket Bold (G) with a 5/16
Inch Washer (J) through the Outer Headboard
Bracket (E) and into Inner Headboard Bracket
(D). Use a 5/16 Inch Washer (J) and 5/16 Inch
Locking Nut (K) and hand tighten to allow
for adjustment. Repeat same procedure for
opposing side of the power base frame.
4. Firmly tighten the headboard bolts (not
included) to the end of the headboard bracket
assembly.
5. Measure the distance of the center to center
mounting holes in the headboard.
6. Measure the distance of the center to center
mounting holes in the headboard bracket
assemblies.
7. If the headboard brackets require adjustments,
loosen the bolts that are holding the outer
headboard brackets and move them to the
necessary distance. Reinstall the bolts and
rmly tighten.
Place your mattress on top of your power base.
Typical Reverie 7T Power Base is now
complete. If the power base is equipped with
a programmable setting or options, refer to the
Remote Control Guide for more information.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
14
App User Guide
Nightlight Feature
How to Download
the App Software
Your Reverie 7T Power Base has a Bluetooth
Accessory Module as standard equipment.
The Bluetooth Accessory Module allows you
to control your power base with your mobile
device using a free, downloadable app. The
module is compatible with the following devices:
iPhone 5 and 6 series
iPad 3, iPad mini, iPad Air
iPod Touch 5th generation
Wi is not required to operate this device
The LED light on the Bluetooth Accessory
Module serves as a nightlight that can be
controlled with the remote control or with the
mobile APP.
STEP 1
STEP 2
STEP 3
STEP 4
Please use any of the previously listed devices
to log into the APP Store.
Type “Reverie Remote” in the search column.
Select the reverie app.
Click install to download the app.
NOTE: Once the App is installed, when
you open the app the Bluetooth Module will
connect to your device automatically.
Reverie 2.0

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
15
App User Guide
Home Screen
• Key features, functions and settings are accessible
from the home screen.
- Settings, Preset List, Comfort Settings, Routines,
Bluetooth, Nightlight, Home Tab, Position Tab,
Massage Tab, and Alarm Tab.
• Reverie Presets – Zero Gravity, Anti-Snore, and Flat
are right at your ngertips.
• Comfort Setting – Press “New +” to program a unique
head, foot and/or massage combination.
• Routines – Press “New +” to program a set of saved or
new comfort settings into a series of timed positions.
Position Control
• Control your head and foot elevation.
• Select the part of the bed you would like to elevate or
lower (head or foot).
- Use your nger to slide the blue dot
along the curve to your desired elevation.
- Or press and hold the plus or minus
symbol to adjust elevation.
• Your position readout on a scale of 1-100 will appear
at the top of the screen and next to the head or foot
position.
• NOTE: Lumbar control is not available on the 7T
adjustable power base.
Massage
• Control your massage intensity and duration.
• Full body – Turns on the full body function.
• Wave – Select number of alternating pulses at the
head and foot of the bed.
• Head and Foot control – Select massage intensity in
the head and foot sections of the bed.
- Use your nger to slide the blue button to your
desired intensity.
- Or press and hold the plus or minus symbol to
adjust intensity.
• Timer – Select your desired massage duration.
• Stop – Turns the massage off.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
16
App User Guide
Alarm
• Create an alarm setting to raise and/or massage you
awake.
• Press “New +” to create a new alarm setting.
- Set time: Scroll to select the hour, minute and day.
- Repeat: Select the days of the week you would
like the alarm to activate.
- Bed control: Select nothing or select a new or
existing comfort setting or routine.
- Snooze: Enable snooze.
Settings
• Customize your app in settings.
• User Prole – Dene your user prole to get
recommendations on custom settings for you.
• Bluetooth – Shows the bed your app is connected to.
Shows nearby beds that you can connect to in order of
proximity.
• Help – Contact info for technical support.
• Mattress Congurator – Recongure your Reverie
Dream or Dream Supreme mattress with these
rmness guides.
• Factory Reset – Reset your app to original settings.
• Logout – Logout or create a new user.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
17
Wireless Remote Control
DISPLAY SCREEN
A. RAISE & LOWER
HEAD SECTION OF THE BASE
B. RAISE & LOWER
FOOT SECTION OF THE BASE
C. RETURN ALL SECTIONS TO FLAT
D. ANTI SNORE
E. ZERO GRAVITY
F. CUSTOM PRESETS
G. NIGHTLIGHT ON/OFF
H. MASSAGE WAVE PATTERN PRESET
I. INCREASE(+) & REDUCE(-) MASSAGE
INTENSITY ON HEAD SECTION OF THE BASE
J. INCREASE(+) & REDUCE(-) MASSAGE
INTENSITY ON FOOT SECTION OF THE BASE
K. STOP ALL MASSAGE FEATURES
L. MICRO USB CHARGING PORT

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
18
Remote Control Operation Guide
OPERATING INSTRUCTIONS:
HEAD AND FOOT ADJUSTMENTS (A,B)
• Adjusts the head and foot sections to the
desired positions.
• Zero Clearance feature allows for the
foundation to be placed on the oor without
legs and able to adjust all sections [head/
foot/lumbar] in a complete motion range
without any of the mechanical parts under
the bed touching the oor. Basically allows
you to use your adjustable bed without legs
if desired.
POWER BASE “FLAT” BUTTON (C)
• Levels the power base to the at position
when the button is pressed and held for at
least 3 seconds.
PROGRAMMABLE MEMORY
BUTTONS (F):
You can store 4 personalized memory
positions.
• To Set a Memory Position: When in desired
position, press and hold Memory button
for more than 5 seconds until the LED light
ashes 3 times to signal Memory position is
stored.
• To recall a Memory Position: Press 1 of the
4 presets.
WAVE MASSAGE PATTERN (H)
• Turns on both head and foot massage
motors to the wave 1 preset.
MASSAGE STOP BUTTON (K)
• Press to stop all massage features.
NOTE: The “FLAT” cycle can be
interrupted and canceled by pressing the
head or foot adjustment buttons (A, B).
NOTE:
All screens will timeout after 5 seconds,
15 seconds if screen is auto-refreshing
NOTE: The lowest setting will turn off the
corresponding massage unit.
NOTE: The massage feature is designed
to automatically shut off after 30 minutes of
continuous use.
ANTI SNORE (D)
• Raises the HEAD slightly for easier
breathing.
ZERO GRAVITY (E)
• Allows your legs to be lifted to a position
slightly above the chest, which enables
blood ow to easily circulate back to the
heart, thus reducing stress and fatigue.
NIGHTLIGHT ON/OFF (G)
• Toggle the lightbulb button for on/off
functions.
HEAD AND FOOT MASSAGE CONTROLS
(I,J)
• Turns on the corresponding massage unit
(starting at intensity 5 of 10)
• Slowly increases or decreases massage
intensity. To increase massage intensity,
press (+) button. To decrease massage
intensity, press (-) button.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
19
Remote Control Operation Guide
ADDITIONAL REMOTE
FEATURES:
• The Reverie 7T power base uses a
Bluetooth® remote control system.
• The included remote is already paired with
your power base, so should be operational
right out of the box. Please test some of the
feature to ensure functionality.
• Only replacement remote controls require
pairing instruction on following pages.
If you nd that your remote is not paired
with the bed, please follow those Bluetooth
pairing instructions.
NOTICE:
The changes or modications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
IMPORTANT NOTE:
• To comply with the FCC RF exposure
compliance requirements, no change to
the antenna or the device is permitted.
Any change to the antenna or the device
could result in the device exceeding the
RF exposure requirements and void user’s
authority to operate the device.
SAFETY:
• If there is an overload weight condition on
the head or foot mechanism, the control unit
will automatically stop all functions.
• The buttons are back-lit, when a button is
pressed, to aid the visibility of the remote in
low light environments.
• Customers can control the remote without
facing the receiver (best transmission range
is within 30 feet or 10 meters)
• The 7T remote is equipped with a
lithium-ion battery that can be recharged
anytime with the included Micro USB wall
charger adapter.
• Please fully charge your remote before
operating.
• The input transformer voltage is AC 120V
60 HZ, the output voltage is DC 24V 3A.
When there is a short circuit, a fuse on the
transformer will be blown in order to protect
the electrical equipment (Fuse: 1.5A).
NOTE: This power base may have minor
intermittent performance due to RF
Interference. This is a normal operation of
the power base and is not a defect.
THIS DEVICE COMPLIES WITH
PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY
NOT CAUSE HARMFUL
INTERFERENCE (2) THIS
DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED
OPERATION.
ATTENTION: When the above situation
occurs, the customer MUST seek
professional assistance.

CUSTOMER SERVICE: 800-973-8374
CUSTOMERSER[email protected]
20
Bluetooth® Pairing
Replacement Remote Control
STEP 1
STEP 4
STEP 5
STEP 6
STEP 2
STEP 3
If two beds are detected then you will be asked
to choose the bed type. [KING or SPLIT KING]
* See decision chart on next page.
If you choose SPLIT KING then you will be
asked if you want to control both sides.
If you choose OTHER then you will be shown a
list of all beds available and asked if you would
like to PAIR MULTIPLE BEDS.
If yes, scroll and select beds to pair.
Ensure the power base is plugged into a
functioning outlet.
Hold lightbulb button for 3 seconds.
If only one bed is discovered the remote will
automatically connect to that bed.
NOTE: If it cannot detect any beds then
will say BED NOT DETECTED.
NOTE:
Please remember to recycle all electronics.