RH Baby&child 355-111 User manual

COLE HOUSE CRIB
Page 1 of 12
TODDLER KIT (SOLD SEPARATELY)
1. Read all instructions before assembly crib. Keep instructions for future use.
2. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
3. Infants can suffocate in gaps between crib sides and a mattress that is too small.
Made in Vietnam
Model No: 355 - 111/112
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 12
COLE HOUSE CRIB
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89cm), the crib shall no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.

Page 3 of 12
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4
INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING
6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib is not more than 1 3/16 inches
(30mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.
COLE HOUSE CRIB

Page 4 of 12
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed must be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310mm) in length, 27 1/4
inches (690mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed must be at least 15 months of age
and must not weigh more than 50 lbs (22.7kg).
WARNING: ENTRAPMENT/STRANGULATION HAZARD
COLE HOUSE CRIB

Page 5 of 12
PARTS INCLUDED:
A
B
C
D
HARDWARE INCLUDED:
[2]
[2]
[1]
[1]
SIDE FRAME
STATIONARY SIDE RAILS
MATTRESS SUPPORT
CENTER STRETCHER
1
2
3
4
5
7
6
Long Bolts 5/16”x 2-1/4”8 pcs.
Short Bolts 5/16”x1-1/2”2 pcs.
2 pcs.
10 pcs.
4 pcs.
4 pcs.
1 pc.
Insert Head 6mm
L Pin 6mm
NO. ITEM DESCRIPTIONQTY.
COLE HOUSE CRIB
A
A
B
B
C
D
Spring Washer 5/16”
Flat Washer 5/16”
Allen Key 4mm

ASSEMBLY INSTRUCTIONS
Note:
- Bed must be assembled by at least two people.
- Please read instructions carefully before
assembling bed.
- Use the above parts and fittings list to identify
each component.
- Keep all packing materials until assembly is
complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps
are finished.
Page 6 of 12
COLE HOUSE CRIB
Attach the Stationary Side Rail (B) to the Side
Frame (A) with Long Bolt (1), Spring Washer (3),
and tighten using Allen Key (7).
DO NOT FULLY TIGHTEN AT THIS TIME.
STEP 1:
STEP 2:
A
A
4x
A
A
A
B
B
1
7
3
Position the Masstres support (C) between the Side
Frame (A).
Note: The Mattress support (C) should be at the
highest level when the child is born.
It must be at the lowest level before the child can
stand up. Before installing the Mattress support (C),
please ask the customer at which height they want
it installed.
C
C
Highest level
Lowest level
Top
Bottom
A
Middle level

Page 7 of 12
COLE HOUSE CRIB
STEP 3:
Position the Stationary Side rail (B)
between the Side Frame (A) and align
the holes.
STEP 4:
A
A
A
A
A
B
C
C
Insert L Pin (6) into empty openings the bottom
of the Mattress Support (C), and into the holes
on the Side Frame (A). Tighten with Insert Head
(5) and Allen Key (7).
4x
6
7
5

Page 8 of 12
After crib is completely assembled,
return to each bolt and tighten to
snug fit. DO NOT over tighten.
WARNING:
COLE HOUSE CRIB
STEP 5:
STEP 6:
A
A
A
A
D
D
A
B
Attach the Stationary Side Rail (B) to
the Side Frame (A) with Long Bolt (1),
Spring Washer (3), and tighten using
Allen Key (7).
Attach the Center Stretcher (D) on the top of
the Side Frame (A) with Short Bolt (2), Spring
Washer (3), Flat Washer (4), and tighten using
Allen Key (7).
1
7
7
3
2
3
4
4x
2x

Page 9 of 12
COLE HOUSE CRIB
8
9
10
11
Small Bolts 5/16”x 3/4”
4 pcs.
2 pcs.
6 pcs.
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm 1 pc.
PARTS INCLUDED:
E
[1] TODDLER RAIL
HARDWARE INCLUDED:
E
Long Bolts 5/16”x 2-1/4”
Spring Washer 5/16”

Page 10 of 12
COLE HOUSE CRIB
Remove Stationary Side Rail (B) from the crib by
carefully unscrew and remove the 4 long bolts
with spring washer on Left/Right sides of the
Stationary Side Rail (B) using Allen Key (11).
STEP 7:
If mattress support is not in the lowest position,
loosen all tightened bolts from side frames.
Spread front of crib open enough to remove
Mattress Support (C), and move it to the lowest
position.
STEP 8:
A
A
4x
4x
4x
A
B
B
B
A
A
11
11
B
Highest
level
Note: The Mattress Support (C) must be at the
lowest level for a toddler bed.
Middle
level
Lowest
level
C
C