RH Baby&child JAMESON CONVERSION CRIB User manual

11
/
1/12

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib shall no longer be used,
and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.
2/12

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height and, when it
is pushed firmly against any side of this crib, it does not leave a
gap of more than 3cm between the mattress and any part of any
other side of the crib.
3/12

IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in thickness, not
exceeding 6" (150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed shall be at least 15 months of
age and shall not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
4/12

PARTS IDENTIFICATION
For ease of identification, all parts are labeled to correspond
to the Step number in which the part is used.
Step 1 Side frame and storage assembly (Page 6)
Step 2 Mattress support assembly (Page 7)
Step 3 Headboard assembly (Page 8 and 9)
Step 4 Front rail assembly (Page 10)
Step 5 Hide unused holes (Page 11)
Step 6 Metal bed frame assembly (Page 12)
HEADBOARD
SIDE RAIL PANEL
MATTRESS SUPPORT
FRONT RAIL
STORAGE
5/12

STEP 1
STORAGE & SIDE RAIL PANEL ASSEMBLY
STEP 1.1
Fully remove the drawers from the storage.
STEP 1.2
Bring the storage and the side panels in upright
position. Align the locator pins on both ends of the
storage to the bore holes in the side panels. Refer
to DETAIL A and DETAIL B.
STEP 1.3
Attach the side panels to the storage by using Allen
bolts (AA) together with lock washers and plain
washers. Please see DETAIL A.
HARDWARE NEEDED FOR STEP 1
Allen Wrench = 1pc
(AA) 1/4" x 2 3/16" Allen Bolt = 4 pcs
(AA)
DETAIL A
DETAIL B
LOCATOR PIN
Lock Washers 1/4" = 4 pcs
Plain Washers 1/4" = 4 pcs
B
A
6/12

STEP 2
MATTRESS SUPPORT ASSEMBLY
STEP 2.1
Attach the support arms to the mattress support, using Allen bolts
(CC), lock washers and plain washers. See DETAIL B.
STEP 2.2
Hang the mattress support on both side panels by using Allen bolts
(CC), lock washers and plain washers to attach the support arms
into the fixed nuts in the side vertical rails of the side panels. See
DETAIL C.
WARNING:
Set the mattress support to the desired height by adjusting the
support arms. The mattress support should be at it's highest setting
for newborns, then adjusted to the lower positions as the child
grows and becomes mobile. Once the child is able to stand, the
mattress support should be at its lowest position.
HARDWARE NEEDED FOR STEP 2
(CC) 1/4" x 13/16 " Allen Bolt = 8 pcs
Lock Washer 1/4" = 8 pcs
Plain Washer 1/4" = 8 pcs
Allen Wrench = 1 pc
DETAIL B
DETAIL C
Support Arm
Plain Washer
Lock Washer
(CC)
Support Arm = 4pcs
Support Arm
(CC)
7/12

STEP 3
HEADBOARD ASSEMBLY
STEP 3.1
Insert the headboard to the back sides of the side
panels.
STEP 3.2
Use Allen bolts (AA), lock washers and plain
washers to attach the crib headboard to the side
panels. Please see DETAIL E and DETAIL F.
(AA)
(AA)
DETAIL F
DETAIL E
HARDWARE NEEDED FOR STEP 3
(AA) 1/4" x 2 3/16" Allen Bolt = 8 pcs
Lock Washers 1/4" = 8 pcs
Plain Washers 1/4" = 8 pcs
Allen Wrench = 1pc
E
F
No use
8/12

STEP 3
HEADBOARD ASSEMBLY
STEP 3.3:
Fix the storage to the headboard posts, using Allen bolts
(AA), lock washers and plain washers. See DETAIL G.
(AA)
DETAIL G
HARDWARE NEEDED FOR STEP 3
(AA) 1/4" x 2 3/16" Allen Bolt = 8 pcs
Lock Washers 1/4" = 8 pcs
Plain Washers 1/4" = 8 pcs Allen Wrench = 1pc
9/12

STEP 4
FRONT RAIL ASSEMBLY
STEP 4.1
Both ends of the front rail have holes for the bolt to pass through
that correspond to the holes on the posts for both side rail panels
with pre-installed nuts. Attach the front rail frame to the side rail
panels by using Allen bolts (BB) with lock washers and plain
washers. See DETAIL H.
STEP 4.2
Use Allen bolts (BB), lock washers and plain washers to fix the
storage to the front rail frame, as illustrated in DETAIL I.
After assembly, re-tighten all bolts for a snug fit. DO NOT OVER
TIGHTEN.
STEP 4.3
Return the drawers to the storage.
DETAIL H
(BB)
HARDWARE NEEDED FOR STEP 4
(BB) 1/4" x 1 1/4 " Allen Bolt = 6 pcs
Lock Washers 1/4" = 6 pcs
Plain Washers 1/4" = 6 pcs
Allen Wrench = 1pc
DETAIL I
(BB)
10/12