RH Baby&child ALEXANDRA TUFTED CRIB User manual

CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and wipe
with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
10640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING: Read all instructions before
assembling this product. KEEP
INSTRUCTIONS FOR FUTURE USE.
ALEXANDRA TUFTED CRIB INSTRUCTIONS
Page 1 of 10

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding.
Never add a pillow or comforter. Never place
additional padding under an infant.
WARNING: Failure to follow these warnings and the
assembly instructions could result in serious injury or death.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on
their backs to sleep, unless otherwise advised by your physician.
Strangulation Hazard:
●Strings can cause strangulation! DO NOT place items with a string around a
child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings over a
crib or attach strings to toys.
●To help prevent strangulation tighten all fasteners. A child can trap parts of the body
or clothing on loose fasteners.
●DO NOT place crib near window where cords from blinds or drapes may strangle a
child.
Fall Hazard:
●When child is able to pull to a standing position, set mattress to lowest position
and remove bumper pads, large toys and other objects that could serve as steps for
climbing out.
●When child is able to climb out or reaches the height of 35 in (90cm), the crib
shall no longer be used, and the child should be placed in a youth or regular bed.
●Check this product for damaged hardware, loose joints, missing parts or sharp edges
before and after assembly and frequently during use. DO NOT use crib if any parts
are missing, damaged or broken. Contact customer service at 1-800-762-1751 for
replacement parts and instructional literature if needed.
●DO NOT substitute parts.
●DO NOT uses a water mattress with this crib.
●If refinishing, use a non-toxic finish specified for children’s products.
●Follow warnings on all products in a crib.
●Never use plastic shipping bags or other plastic film as mattress covers because
they can cause suffocation.
●Infants can suffocate in gaps between crib sides and a mattress that is too small.
Page 2 of 10

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN
THIS CRIB MUST BE AT LEAST 27-1/4
INCHES BY 51-5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
WARNING
●Do not use this crib if the enclosed or attached instructions
cannot be strictly adhered to. Do not use this crib if the child is
able to climb out unaided or is taller than 35 in (90 cm). Do not
place cords, straps or similar items that could become wound
around the child’s neck in or near this crib. Ensure that the sides
are properly latched or locked in place when the crib is
occupied. The mattress used with this crib should not be more
than 6 in (15 cm) thick and should be of such length and width
that the gap between the mattress and the sides of the crib is
not more than 1-1/5 in (3 cm) when the mattress is pushed into
the corner of the crib.
●Parents should inspect the crib regularly before putting the
child in the crib each day and confirm that every component of
the crib is properly and securely in place.
Page 3 of 10

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION
HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could result in
serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may
strangle a child.
●The mattress intended for use on the bed shall be a full-size crib mattress having
minimum dimensions of 51-5/8 inches (1310mm) in length, 27-1/4 inches (690mm) in
width and 4 inches (100 mm) in thickness, not exceeding 6 inches (152 mm) in
thickness.
●If guardrails are used as the mattress containment means, guardrail(s) provided must
be used to avoid the formation of a gap between the mattress and the bed that could
cause an entrapment.
●DO NOT place bed near windows where cords from blinds or drapes may strangle a
child.
●DO NOT place items with a string, cord, or ribbon around a child’s neck, such as hood
strings or pacifier cords.
●DO NOT suspend strings over a toddler bed for any pacifier cords.
●A child using the toddler or day bed shall be at least 15 months of age and shall not
weigh more than 50lbs (22.7kgs).
Page 4 of 10

ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to
the Step number in which the part is used.
Step #1 First side rail and end panel assembly (Page 6)
Step #2 Mattress Support Arm assembly Stabilizer Rail assembly
Mattress height adjustment (Page 7)
Step #3 Installation of Stabilizer Rail into the end panels (Page 8)
Step #4 Second side rail assembly (Page 9)
Step #5 Toddler rail assembly (Page 10)
SIDE RAIL
END PANEL
MATTRESS SUPPORT
Page 5 of 10

STEP #1
1ST SIDE RAIL & END PANEL ASSEMBLY
Attach the the first side rail to the end panels by using Allen bolts (AA),
lock washers and plain washers. See Detail A.
HARDWARE NEEDED FOR STEP #1:
ALLEN WRENCH = 1PC
LOCK WASHERS 1/4" = 4 PCS
PLAIN WASHERS 1/4" = 4 PCS
(AA) 1/4" X 1-3/4" BOLT = 4 PCS
DETAIL A
(AA)
Page 6 of 10

LOCK
WASHER
B
C
DETAIL B
DETAIL C
HEX NUT
PLAIN
WASHER
ALLEN BOLT
(BB)
ALLEN
WRENCH
ALLEN WRENCH
OPEN WRECH
HEX NUT
LOCK WASHER
PLAIN WASHER
MATTRESS
SUPPORT
STABILIZER RAIL
HARDWARE FOR STEP #2:
LOCK WASHER = 8 PCS
PLAIN WASHER = 8 PCS
HEXAGONAL NUT = 8 PCS
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
OPEN WRENCH = 1 PC
ALLEN WRENCH = 1 PC
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
(BB) 1/4" X 1-1/4" BOLT = 8 PCS
STEP #2.1
Lay Mattress Support flat with Stabilizer Rail on each side.
NOTE:
On each end of the arm of the Mattress Support, there is a hole for the
bolt to pass through that corresponds to the holes located in the frame of
the Mattress Support.
STEP #2.2:
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
Mattress Support. See DETAIL B.
WARNING:
Set the Mattress Support to the desired height by adjusting the Support
Arms. The Mattress Support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the Mattress Support
should be at its lowest position.
STEP #2.3:
Install the Stabilizer Rail at ends of the arm support, as illustrated in
DETAIL C.
Page 7 of 10

DETAIL D
HARDWARE FOR STEP #3:
STEP #3
INSTALLATION OF STABILIZER RAILS INTO
THE END PANELS
(CC) 1/4" X 13/16 " BOLT = 4 PCS
LOCK WASHER = 4 PCS
PLAIN WASHER = 4 PCS
DETAIL E
(CC)
ALLEN WRENCH = 1 PC
STEP #3.1
On inside surface of both end panels are pre-installed
metal brackets, designed to hold the Stabilizer Rails. Set
both ends of the Stabilizer Rails into brackets, as illustrated
in DETAIL D.
STEP #3.2
Hold the mattress support and lay down the crib then
fasten the Stabilizer Rails with bolts (CC), plain washers
and lock washers provided, as illustrated in DETAIL E.
Page 8 of 10

STEP #4
2ND SIDE RAIL ASSEMBLY
Attach the second side rail to the end panels by using Allen
bolts (AA), lock washers and plain washers. See Detail F.
After assembly, re-tighten all bolts to a snug fit. DO NOT
OVER TIGHTEN.
HARDWARE NEEDED FOR STEP #4:
LOCK WASHERS = 4 PCS
PLAIN WASHERS = 4 PCS
(AA) 1/4" x 1-3/4" BOLT = 4 pcs
(AA)
DETAIL F
ALLEN WRENCH = 1 PC
Page 9 of 10

Page 10 of 10
STEP #5
TODDLER RAIL ASSEMBLY
STEP #5.1:
Remove the front rail panel of the crib by loosening all the bolts
installed.
STEP #5.2:
Gently tilt the crib and release the bolts underneath the metal
brackets holding the stabilizer rails.
STEP #5.3
Gently remove the mattress support and slightly loosen the bolt
at the back of the headboard that enough to set the toddler rail
in-between side rail panel.
NOTE: Fill the holes located on the top of both side rail panel by
inserting bolt (Ø1/4x1/2") provided. See Detail G.
STEP #5.4
On inside face of both side rail panels there is a cavity for the
hooks, which corresponds to the hooks on both ends of the
toddler rail. Align and insert the hooks of the toddler rail into the
cavity of the side rail panel. See Detail H.
-NOTE: If mattress support is not in the lowest position, unscrew
mattress support bolts and move the lowest position.
STEP #5.5
Repeat step #3. Installation of stabilizer rails into the side panel
(DETAIL E).
After assembly, re-tighten all bolts to a snug fit.
DETAIL H
H
G
DETAIL G
ALLEN BOLT
Ø1/4" X 1/2"
DETAIL E
HARDWARE FOR STEP #5
1/4" X 1/2" BOLT = 2 PCS