RH Baby&child BELLE UPHOLSTERED CONVERSION CRIB 195 -... User manual

BELLE UPHOLSTERED CONVERSION CRIB
Page 1 of 25
Made in Vietnam
Model No: 195 - 36/32
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
TODDLER BED CONVERSION KIT (SOLD SEPARATELY)
1. Read all instructions before assembly crib. Keep instructions for future use.
2. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
3. Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 25
BELLE UPHOLSTERED CONVERSION CRIB
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89cm), the crib shall no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.

Page 3 of 25
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4
INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING
6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib is not more than 1 3/16 inches
(30mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.
BELLE UPHOLSTERED CONVERSION CRIB

Page 4 of 25
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310mm) in length, 27 1/4
inches (690mm) in width and 4 inches (100mm) in thickness, not
exceeding 6 inches (152mm) in thickness.
If guardrails are used as the mattress containment means, the guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50 lbs (22.7kg).
WARNING: ENTRAPMENT/STRANGULATION HAZARD
BELLE UPHOLSTERED CONVERSION CRIB

Page 5 of 25
PARTS INCLUDED:
A
B
C
D
E
F
HARDWARE INCLUDED:
[1]
[1]
[1]
[1]
[1]
[2]
HEADBOARD
FOOTBOARD
LEFT SIDE RAIL
RIGHT SIDE RAIL
MATTRESS SUPPORT
STRETCHER BARS
A
D
C
B
F
E
1
2
3
4
12mm
5
6
Threaded Rod
5/16" x 2-1/2"
NO. ITEM DESCRIPTIONQTY.
Curved Slotted Washer
5/16" x 30 x 15 x 3mm
Hex Nut
5/16"x 12 x 12mm
Hex Wrench 12mm
Small Bolts 1/4" x 3/4"
Metal Bracket
BELLE UPHOLSTERED CONVERSION CRIB
4 pieces
2 pieces
4 pieces
4 pieces
4 pieces
1 piece

Page 6 of 25
7
8
9
10
11
12
13
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm
Long Bolts 5/16" x 2-1/2"
Short Bolts 6 x 32mm
Middle Bolts 6 x 40mm
Hex Nut 6 x 10mm
Spring Washer 1/4" x 10mm
Flat Washer 1/4" x 16mm
14 Cap Nut 6 x 10mm
15 Half Moon Washer
28 x 14.5 x 7.5mm 4 pieces
16 pieces
4 pieces
4 pieces
16 pieces
4 pieces
12 pieces
6 pieces
1 piece
10 mm
16 1 piece
Hex Wrench 10mm
BELLE UPHOLSTERED CONVERSION CRIB

ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the above parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
Page 7 of 25
2
C
D
STEP 1:
Attach Metal Brackets (2) to the Left/Right Side Rails (C, D)
using Small Bolts (1) and Allen Key (7) to tighten (as shown
in Diagram 1).
Then secure the Threaded Rod (3) into the Left/Right Side
Rails (C, D) (as shown in Diagram 2).
7
1
3
Diagram 1
Diagram 2
BELLE UPHOLSTERED CONVERSION CRIB

STEP 2:
Page 8 of 25
Raise the Footboard (B) up and place the rod into the
Left/Right Side Rails (C, D) at the bore holes' position.
Insert Curved Slotted Washer (4), Hex Nut (5) using
Hex Wrench (6) to tighten (as shown in Diagram 3).
Then attach the Footboard (B) to the Left/Right Side
Rails (C, D) by using Small Bolts (1) and tighten with
Allen Key (7) (as shown in Diagram 4).
6
5
4
3
2
C
B
D
7
1
Diagram 3
Diagram 4
BELLE UPHOLSTERED CONVERSION CRIB

STEP 3:
Page 9 of 25
Raise the Headboard (A) up and place the rod into the
Left/Right Side Rails (C, D) at the bore holes' position.
Secure the Threaded Rod (3 ) into the Headboard (A).
STEP 4:
A
A
D
C
3
3
BELLE UPHOLSTERED CONVERSION CRIB

Page 10 of 25
STEP 5:
STEP 6:
Attach the Headboard (A) to the Left/Right Side
Rails (C, D) using Long Bolt (8) and tighten with
Allen key (7).
8
7
5
6
4
3
Place the Crib down on a flat and smooth
surface.
Attach the Left/Right Side Rails (C, D) to
the Headboard (A) by inserting Curved
Slotted Washer (4), Hex Nut (5) and using
Hex Wrench (6) to tighten.
BELLE UPHOLSTERED CONVERSION CRIB

STEP 7:
Page 11 of 25
Note: The Mattress Support (E) should be at the highest level
when the child is born. It must be at the lowest level before the
child can stand up. Before installing the Mattress support (E),
please ask the customer at which height they want it installed.
E
Attach scissor assembly bars to
the Mattress Support (E) using
Short Bolts (9), Hex Nut (11) and
Cap Nut (14). Tighten with Allen
Key (7) and Hex Wrench (16).
Next, insert the Small Bolts (9) in
the upper holes of the Mattress
Support (E) using Hex Nut (11) and
Cap Nut (14). Tighten with Allen
Key (7) and Hex Wrench (16).
79
11 16
14
Highest level
Lowest level
Middle level
11
79
14
16
BELLE UPHOLSTERED CONVERSION CRIB

STEP 8:
Page 12 of 25
F
F
F
Attach the Mattress Support (E) to
the Stretcher Bars (F) using Middle
Bolts (10), Flat Washer (13), Spring
Washer (12), Hex Nut (11) and Cap
Nut (14). Tighten with Allen Key (7)
and Hex Wrench (16).
16
1411
12
13
10
7
BELLE UPHOLSTERED CONVERSION CRIB

STEP 9:
Page 13 of 25
Secure the Mattress Support (E)
into the crib.
Then, insert Long Bolts (8) and
Half Moon Washer (15) and
tighten with Allen key (7).
F
E
7
815
BELLE UPHOLSTERED CONVERSION CRIB

STEP 10:
Page 14 of 25
After crib is completely assembled, return
to each bolt and tighten to snug fit.
DO NOT over tighten.
WARNING:
Carefully turn the Crib upright.
BELLE UPHOLSTERED CONVERSION CRIB

Page 15 of 25
PARTS INCLUDED:
G[1] TODDLER RAIL
G
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm
Long Bolts 5/16" x 2 1/2" 2 pieces
2 pieces
Half Moon Washer
28 x 14.5 x 7.5mm
1 piece
HARDWARE INCLUDED:
17
18
19
BELLE UPHOLSTERED CONVERSION CRIB

Page 16 of 25
STEP 11:
Place the Crib down on a flat and smooth surface.
Carefully unscrew and remove the 4 Long Bolts (8)
with Half Moon Washer (15) on the Stretcher Bars (F)
using Allen Key (17).
Remove the Mattress Support (E) from the crib.
17
F
E
8
15
BELLE UPHOLSTERED CONVERSION CRIB

Page 17 of 25
STEP 12:
Remove the 4 Hex nuts (5) with
Curved Slotted Washer (4) on the
Left/Right Side Rails (C, D) using
Hex Wrench (6).
STEP 13:
8
17
6
D
C
5
4
Remove the 4 Long Bolts (8) on
back of the Headboard (A) using
Allen Key (17).
BELLE UPHOLSTERED CONVERSION CRIB

Page 18 of 25
A
STEP 15:
6
5
4
3
C
B
B
D
7
1
STEP 14:
Remove the Headboard (A) from
the crib.
Remove the Footboard (B) from
the crib by carefully unscrew and
remove the 2 Small Bolts (1) and
2 Hex Nuts (5) with Curved Slotted
Washer (4) on the Footboard (B).
BELLE UPHOLSTERED CONVERSION CRIB

Page 19 of 25
STEP 16:
2
C
D
7
1
3
G
C
D
17
19
18
Remove Metal Bracket (2) from the Left/Right
Side Rails (C, D) by unscrew and remove the
Small Bolt (1) with Allen Key (7).
Next, remove the Threaded Rod (3) from the
post of the Left/Right Side Rails (C, D).
STEP 17:
Place the hooks of the Toddler Rail (G) into
the slots in the Left/Right Side Rails (C, D).
If ecessary, using a thick magazine or book
to protect the Toddler Rail (G), hammer with
a mallet or hammer until tight.
Then, insert Long Bolt (18) and Half Moon
Washer (19) with Allen Key (17) to tighten.
BELLE UPHOLSTERED CONVERSION CRIB

Page 20 of 25
STEP 18:
STEP 19:
Attach the Headboard (A) to the
Left/Right Side Rails (C, D) using
Long Bolt (8) and tighten with
Allen Key (17).
8
17
6
5
4
3
Attach the Left/Right Side Rails (C, D) to
the Headboard (A) by insert Curved
Slotted Washer (4), Hex Nut (5) and using
Hex Wrench (6) to tighten
BELLE UPHOLSTERED CONVERSION CRIB