RH Baby&child BELLINA CONVERSION CRIB TODDLER BED KIT User manual

BELLINA CONVERSION CRIB TODDLER BED KIT INSTRUCTIONS
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the
address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully
package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Page 1 of 7

Page 2 of 7
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION
HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could result
in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may
strangle a child.
● The mattress intended for use on the bed shall be a full-size crib mattress having minimum
dimensions of 51-5/8 inches (1310mm) in length, 27-1/4 inches (690mm) in width and 4 inches
(100 mm) in thickness, not exceeding 6 inches (152 mm) in thickness.
● If guardrails are used as the mattress containment means, guardrail(s) provided must be
used to avoid the formation of a gap between the mattress and the bed that could cause an
entrapment.
● DO NOT place bed near windows where cords from blinds or drapes may strangle a child.
● DO NOT place items with a string, cord, or ribbon around a child’s neck, such as hood
strings or pacifier cords.
● DO NOT suspend strings over a toddler bed for any pacifier cords.
● A child using the toddler or day bed shall be at least 15 months of age and shall not weigh
more than 50lbs (22.7kgs).

Page 3 of 7
WARNING: ADULT ASSEMBLY ONLY, OWING TO THE PRESENCE OF
SMALL PARTS, SHARP POINTS AND EDGES.
CAUTION
TODDLER BED: THE MINIMUM AGE SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALL NOT BE GREATER THAN 50LBS. (22.7 KG).
THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING
MINIMUM DIMENSIONS OF 51-5/8 IN. (1310MM) IN LENGTH, 27-1/4 IN(690MM)IN WIDTH AND 4 IN. (100MM)
IN THICKNESS NOT EXCEEDING 6 IN. (152MM) IN THICKNESS.
CARE INSTRUCTIONS:
• Dust often using a clean, soft, dry, lint- free cloth.
• Blot spills immediately, and wipe with a clean, damp cloth.
• We do not recommend the use of chemical cleaners, abrasives, or furniture polish on our lacquered finish.
A. BELLINA CONVERSION HEADBOARD
B. BELLINA CONVERSION END RAIL PANELS
C. BELLINA CONVERSION TODDLER BED KIT
D. MATTRESS SUPPORT
TODDLER CONVERSION KIT
ASSEMBLY HARDWARE IS
INCLUDED IN THE TODDLER
KIT BOX.
PART LIST
ALLEN WRENCH = 1PC
(EE) 1/4" x 1/2" BOLT = 2 PCS.
HARDWARE

Page 4 of 7
DETAIL B
DETAIL A
ASSEMBLY INSTRUCTIONS
STEP #1.
FRONT RAIL DISASSEMBLY.
STEP #1.1:
Remove the Front Rail Panel of the crib by loosening all the bolts
installed, as in DETAIL A.
STEP #1.2:
Gently tilt the Crib and release the bolts underneath the metal
brackets holding the Stabilizer Rails as in DETAIL B.
NOTE:
• Slightly loosen the bolt at the back of the Headboard that
enough to set the Toddler Tail in-between End Rail Panels.

Page 5 of 7
DETAIL C
STEP #2.
TODDLER RAIL ASSEMBLY.
STEP #2.1
On inside face of both End Rail Panels there is a cavity for the hook
which corresponds to the hook on both end of the Toddler Rail.
Align and insert the hook of the Toddler Rail into the cavity of the
End Rail Panel, as in DETAIL C.
STEP #2.2
Fill the holes located on the top of both end of the side panel by
inserting bolt (EE) provided.
EE
EE
HARDWARE
ALLEN WRENCH = 1PC
(EE) 1/4" x 1/2" BOLT = 2 PCS.

Page 6 of 7
E
STEP #3
MATTRESS SUPPORT HEIGHT ADJUSTMENT
NOTE: If mattress supports is not in the lowest position.
STEP #3.1
Loosen and remove all hardware (BB) on both sides of the frame of
mattress support.
STEP #3.2
Re-install the bolt on the third hole of the frame through the hole on the
arm support. Fasten the bolt with plain washers, lock washers &
hexagonal nut. Repeat procedure on the other arms of the mattress
support. See DETAIL D & DETAIL E.
DETAIL E
MATTRESS
SUPPORT
STABILIZER RAIL
LOCK
WASHER
HEX NUT
PLAIN
WASHER
ALLEN BOLT
(BB)
ALLEN
WRENCH
DETAIL D
HARDWARE
(BB) 1/4" X 1-1/4" BOLT = 8 PCS PLAIN WASHER = 8 PCS
LOCK WASHER = 8 PCS
HEX NUT = 8 PCS
ALLEN WRENCH = 1 PC 11 X 70
OPEN WRENCH = 1 PC
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)

Page 7 of 7
STEP #4
INSTALLATION OF STABILIZER RAILS
INTO THE SIDE PANEL.
STEP #4.1
On inside face of both End Rail Panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends of
the stabilizer rails into brackets, as illustrated in DETAIL F.
STEP #4.2
Once the stabilizer rails are set, gently tilt the toddler bed and
fasten the stabilizer rails with bolt, lock washer and plain washer.
See DETAIL G.
NOTE
After assembly, re-tighten all bolts to a snug fit.
DETAIL F
DETAIL G