RH Baby&child BELLINA Operation instructions

11
/
1/11

2/11
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation, tighten all fasteners. A child can trap parts of his/her body or clothing
on loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull himself/herself to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib should no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

3/11
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE
AT LEAST 27 1/4" X 51 5/8" WITH A HEIGHT
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing, or if there are any signs of damage.
Do not substitule parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no more than 6" (15cm) in height and, when
it is pushed firmly against any side of this crib, does not leave a
gap of more than 1 3/16" (3cm) the mattress and any other side of
the crib.

4/11
IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed should be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in height, not
exceeding 6" (152mm) in thickness.
·If guardrails are used to contain the mattress, the guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed should be at least 15 months of
age and should not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

HEADBOARD
END RAIL PANEL
STATIONARY FRONT
RAIL ASSEMBLY
MATTRESS SUPPORT
Step 1 Leg assembly to headboard and end rail panel
Headboard and end rail panel assembly (Page 6)
Step 2 Mattress support and stabilizer rail assembly
Mattress height adjustment (Page 7)
Step 3 Stabilizer rail & end rail panel assembly (Page 8)
Step 4 Stationary front rail assembly (Page 9)
Step 5 Toddler rail assembly (Page 10)
Step 6 Metal bed frame assembly (Page 11)
PARTS IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the
Step number in which the part is used.
5/11

(AA)
STEP 1
LEG ASSEMBLY TO HEADBOARD AND END RAIL PANEL
HEADBOARD AND END RAIL PANEL ASSEMBLY
STEP 1.1
Gently lay the headboard and end rail panel on their backs on
a clean and non-abrasive surface.
STEP 1.2
Align and insert the threaded rod of the legs into the hole on
the bottom of the headboard and end rail panel and turn
clockwise to tighten. See DETAIL A.
STEP 1.3
Bring the headboard and end rail panel in upright position.
NOTE:
On both end of the headboard are holes for the bolt to pass
through that correspond to the holes located on both ends of
the end rail panel with pre-installed nuts.
STEP 1.4
Align the hole of the end rail panel with the holes of the
headboard then insert allen head bolt into hole and tighten
with allen wrench provided. See DETAIL B.
DETAIL A
HARDWARE FOR STEP 1
Allen Wrench = 1 pc.
(AA) 1/4" x 1 3/4" Allen Bolt = 4 pcs.
Lock Washer = 4 pcs.
Plain Washer = 4 pcs.
DETAIL B
6/11

Lock Washer
B
C
STEP 2
MATTRESS SUPPORT ARM ASSEMBLY STABILIZER
RAIL ASSEMBLY MATTRESS HEIGHT ADJUSTMENT
STEP 2.1
Lay mattress support flat with stabilizer rail on each side.
NOTE:
On each end of the arm of the mattress support, there is a hole for the bolt
to pass through that corresponds to the holes located in the frame of the
mattress support.
STEP 2.2
Insert the allen bolt into the desired hole of the frame through the hole on
the arm support. Fasten the bolt with plain washers, lock washers and
hexagonal nuts provided. Repeat procedure on other arms of the mattress
support. See DETAIL C.
WARNING:
Set the mattress support to the desired height by adjusting the support
arms. The mattress support should be at its highest setting for newborns,
then adjusted to the lower positions as the child grows and becomes
mobile. Once the child is able to stand, the mattress support should be at
its lowest position.
STEP 2.3
Install the stabilizer rail at ends of the arm support, as illustrated in
DETAIL D .
DETAIL C
DETAIL D
Hex Nut
Plain Washer
Allen Bolt (BB)
Allen Wrench
Open Wrech
Hex Nut
Lock Washer
Plain Washer
Mattress Support
Stabilizer Rail
HARDWARE FOR STEP 2
(BB) 1/4" x 1 1/4" Allen Bolt = 8 pcs.
Plain Washer = 8 pcs.
Lock Washer = 8 pcs.
Hex Nut = 8 pcs.
Allen Wrench = 1 pc. 11 X 70
Open Wrench = 1 pc.
Allen Bolt (BB)
Allen Bolt (BB)
Allen Bolt (BB)
Allen Bolt (BB)
Open Wrench
7/11

STEP 3
INSTALLATION OF STABILIZER RAILS INTO
THE END RAIL PANELS DETAIL E
DETAIL G
DETAIL F
STEP 3.1
On inside face of both end rail panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends
of the stabilizer rails into brackets, as illustrated in DETAIL E.
STEP 3.2
Once the stabilizer rails are set, gently tilt the crib as
illustrated in DETAIL F, and then fasten the stabilizer rails
with allen bolt, lock washer and plain washer provided, as
illustrated in DETAIL G.
HARDWARE FOR STEP 3
(CC) 1/4" x 13/16" Allen Bolt = 4 pcs.
Lock Washer = 4 pcs.
Plain Washer = 4 pcs.
Allen Wrench = 1 pc.
8/11

STEP 4
STATIONARY FRONT RAIL ASSEMBLY DETAIL H
STEP 4.1
On both ends of the end rail panel are holes for the bolt to
pass through which correspond to the holes on the posts of
both end rail panel with pre-installed nuts. Align the holes of
the front rail panel into the end rail panels then engage allen
bolt in each hole and tighten with allen wrench provided, as
in DETAIL H AND DETAIL I.
After assembly, re-tighten all bolts to a snug fit. DO NOT
OVER TIGHTEN.
DETAIL I
HARDWARE FOR STEP 4
Allen Wrench = 1 pc.
(AA) 1/4" x 1 3/4" Allen Bolt = 4 pcs.
Lock Washer = 4 pcs.
Plain Washer = 4 pcs.
9/11

EE
STEP 5
TODDLER RAIL ASSEMBLY
DETAIL J
DETAIL K
STEP 5.1
Remove the front rail panel of the crib by loosening all the bolts
installed.
STEP 5.2
Gently tilt the crib and release the bolts underneath the metal
brackets holding the stabilizer rails.
STEP 5.3
Gently remove the mattress support and slightly loosen the bolt
at the back of the headboard that enough to set the toddler rail
in-between end rail panel.
NOTE: Fill the holes located on the top of the end rail panel by
inserting bolt (EE) provided.
STEP 5.4
On inside face of both end rail panels there is a cavity for the
hook which corresponds to the hook on both ends of the toddler
rail. Align and insert the hook of the toddler rail into the cavity of
the end rail panel, as in DETAIL J.
NOTE: If mattress support is not in the lowest position, unscrew
mattress support bolts and move the lowest position.
STEP 5.5
Repeat step 3. Installation of stabilizer rails into the end rail
panel (DETAIL K).
After assembly, re-tighten all bolts to a snug fit.
Allen Wrench = 1 pc.
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs.
HARDWARE FOR STEP 5:
EE
EE
10/11